from

$157.99

K&N’s replacement air filters are designed to increase horsepower and acceleration while providing excellent filtration. We make over 1,200 different replacement air filters for the majority of vehicles on the road. These filters are washable and reusable and are custom designed to fit into your existing factory air box. Their drop-in design means adding performance is simple. With most vehicles you simply remove the disposable air filter and replace it with a K&N. See applicable instruction sheet for details. Our stock replacement air filters for street vehicles are covered by our famous K&N Million-Mile Limited Warranty and will be the last air filter your vehicle will ever need.

Product Features:

This is the last air filter your vehicle will ever need!
Designed to boost horsepower and rate of acceleration
Can be cleaned and used again
High air flow with exceptional filtration
Lasts up to 50,000 miles before cleaning is required depending on driving conditions
Works with original equipment manufacturer vehicle electronics
Emissions legal in all 50 US states
Will NOT void vehicle warranty
Million Mile Limited Warranty®

from

$87.99

Made from heavy gauge steel, this chrome plated rear end cover comes complete with bolts and gaskets.

Product Features:

Chrome plated steel for looks
Includes bolts and gasket

from

$44.99

These brackets are made from heavy gauge steel, polished to a high luster, then chrome plated for lasting beauty. Similar in design to original equipment units.

Product Features:

Fits Small Block Ford 1965-’69 – OEM Style
Polished To High Luster
Chrome Plated For Lasting Beauty

from

$620.99

MSD is excited to offer two Ready-to-Run distributors for two classic Ford engines! These distributors are the answer to weak breaker points or rebuilt aftermarket models. Inside the billet housing there is a high-output ignition module. When the maintenance-free magnetic pick-up signals the module to fire, up to 7.5 A is sent to the coil where a powerful spark is created. This improved spark output results in quick starts, snappy throttle response and terrific drivability. The distributors are equipped with a vacuum advance canister for cruising economy. Plus, there is a mechanical advance assembly that is mounted on top of the distributor shaft making it easy to adjust the advance to meet your needs. Another great feature of the Ready-to-Run distributors is their simple installation! All you need to do is connect three wires and you’ll be cruising!

Product Features:

Simple and clean three wire installation
CARB E.O. Approved
Does not require an MSD Ignition Control
Supplied w/small dia. cap w/HEI style terminals; race and rotor
Will accept PN[8441] Cap-A-Dapt
Nylon pads ensure smooth operation of the advance weights
Advance weight pins are staked and tig welded to the plate
Mech. advance assem. can be locked out for crank trigger systems

from

$101.99

Product Features:

MINI SPOOL – DANA 44, 30 SPL.

from

$379.99

The Edelbrock part #41603 Classic Series Valve Covers are designed for Ford 221-351W V8 1962-95 applications and have a Black finish. Edelbrock first made these aluminum valve covers in the late ’50s and they’re still a classic. Made of heavy-gauge sand-cast aluminum, Overall height is measured from base to top at the highest point. Edelbrock classic valve covers can be machined to accept breathers if desired.

Product Features:

Small Block Ford 221-351W 62-95
Tall
Black Aluminum
Set Of Two

from

$404.99

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.

Product Features:

Good blend of efficiency and performance.
Perfect choice for performance street rebuilds.
Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

from

$33.99

Product Features:

Service Part
Makes Connections Quick And Easy

from

$577.99

RngPnn

from

$376.99

Edelbrock #88433 Water Pump Ford 1970-78 302 & 1970-87 351w v8 black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cool

Product Features:

Standard Impeller Rotation
0.625 in. Pilot Shaft
0.750 in. Ball/Ball Bearing
5.70 in. Block To Hub Height
Black Finish

from

$1087.99

Product Features:

Complete Single For Flat Tappet
60cc Combustion Chamber Volume
170cc Intake/60cc Exhaust Runner Volume
2.02 in. Intake/1.60 in. Exhaust Valve Diameter
0.625 in. Deck Thickness

from

$86.99

Regain horsepower and economy for your street machine with new contact and condenser kit. Large tungsten contacts provide crisp coil firing and perform solidly up to 5,000 RPM. Condenser’s special winding protects from pitting of point contacts. Heavy duty 23 ounce points.

Product Features:

High Performance Points and Condenser
With Integral Conductor

from

$95.99

Product Features:

Made of Superior Hyper-Flex+ Material
Maintain Proper Caster Alignment

from

$34.99

Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Manufactured from high-density cork/rubber blend gasket material
Provides excellent sealing and durability
For OE replacement, high performance street, drag race and oval track use

from

$414.99

Burnished aluminum. GM/MAC- style throttle linkage. Electric choke installed from factory. Easy tuning with 2 piece design. Smooth secondary transition. Both timed for full vacuum ports. Includes PCV outlet.

from

$476.99

Rocker Arms,FS/FW 1.6 7/16 Ultra Pro Mag

from

$149.99

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

Easy Installation
Improved Fuel Economy
Reduced Maintenance
Accurate Timing
Improved Performance
Provides A Simple Conversion
No Moving Parts To Wear Out

from

$141.99

Product Features:

Use W/ Valve Springs Part #5722, 5796
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$74.99

Replace your stock black engine pulleys with chrome plated steel pulleys from Mr. Gasket.

Product Features:

Triple Groove
Chrome Plated
Diameter: 5.90″

from

$85.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets

from

$395.99

2500-6500 RPM high-performance street engines. Single-plane low-rise intake good for high RPM. Ideal for applications with limited hood clearance. For top-end HP and adequate throttle response. Available in cast or polished.

Product Features:

2500 to 6500 RPM High Performance Street Engines
Single-Plane Low-Rise Intake Good for High RPM
Ideal for Applications with Limited Hood Clearance
For Top-End HP and Adequate Throttle Response

from

$117.99

Product Features:

PINION YOKE
CAST:1310
U-BOLT STYLE

from

$112.99

Will replace distorted and worn-out original rubber mounts to maintain car body and truck cab to bed alignment. Original rubber mounts are so soft they often crack, distort, and crush so badly they often fall off and aluminum body mounts are too harsh for street use that they tend to break and cause other components to break. Energy’s specially formulated Hyper-Flex polyurethane cab and body mounts combine the best qualities of both: they’re soft enough for a smooth ride, yet rugged enough for the most demanding road or track. Most sets have a strong zinc plated steel ring molded into them – for added durability and when the application requires it.

Product Features:

Assures Longer Lasting Cab to Bed Alignment
Replace to Restore Ride Height
Gain Durability
Stronger Than Original Rubber Mounts

from

$80.99

Rancho® high-performance steering stabilizers are a simple and affordable way to enhance a vehicle’s performance. Rancho® steering stabilizers are ideal for off – road driving, towing/hauling and street performance applications. Rancho® steering stabilizers are engineered for vehicles with oversized wheels and tires which reduce wheel shimmy, bump steer and vibration. They are available in single and dual configurations with bracket kits available for vehicles without OE mounts. Rancho® steering stabilizers are made with a liquid metallic finish which provides a premium long lasting finish along with a boot that protects the shock rod and oil seal. Rancho® steering stabilizers are covered by our limited lifetime warranty that guarantees your investment. Check our website to find the Rancho® steering stabilizers RS5000¿ part numbers for your vehicle.

Product Features:

Black powder coated for visual appeal
CNC cut or bent
Steel thickness
Direct bolt to factory steering linkage
Designed for dual steering stabilizer

from

$153.99

The Monro-Magnum steering stabilizer stops vibration before it gets to the driver. Acting as a horizontal shock absorber, Monro-Magnum steering stabilizers help reduce vibrations that travel through the steering system to the driver.

Product Features:

Half inch Piston Rod: Heavy-duty nitrocarburized rod for long service life
All Weather Fluid: Contains special modifiers to reduce friction and ensure smooth rod reaction.
Full Displaced Valving: Better valving range on both the compression and extension cycles of the unit for a smooth comfortable ride.
Micro-Cellular Gas Design: Allows unit to be mounted horizontally.
Sintered Iron Piston: Stronger than traditional metals, enhances durability for longer service life.
Special Seal: ‘Self-lubricating’ fluid seal designed to retain gas without excessive wear or friction.