1999 Chevrolet Blazer Performance Engines
More 1999 Chevrolet Blazer Performance Engines
Find your specific 1999 Chevrolet Blazer original or aftermarket Performance Engines below. Order your parts online and have delivered to your home or pick up in-store at Advance Auto.
Essential 1999 Chevrolet Blazer Performance Engines
B & M – Torque Converter, Holeshot 3000 (Part No.70421)
from
$789.99
The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, New turbine hub and dual pattern drive lugs on some GM Holeshots.
Product Features:
See More
Product Features:
- Furnace Brazed Impeller
- Steel Alloy Pump Drive Tube
- Heavy Duty Needle Bearing
- Between Stator and Turbine
- Furnace Brazed Turbine
B & M – Torque Converter, Nitrous Holeshot 3000 (Part No.20481)
from
$766.99
Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.
Product Features:
See More
Product Features:
- 2800-3200 RPM
- Small And Big Blocks
- Serious Performance
- Furnace Brazed
- Fully Balanced
B & M – Torque Converter, Nitrous Holeshot 3600 (Part No.20482)
from
$665.99
Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.
Product Features:
See More
Product Features:
- 3400-3800 RPM
- Small And Big Blocks
- Serious Performance
- Furnace Brazed
- Fully Balanced
B & M – Torque Converter, Holeshot 2000 (Part No.70417)
from
$544.99
The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, new turbine hub and dual pattern drive lugs on some GM Holeshots.
Product Features:
See More
Product Features:
- Furnace Brazed Impeller
- Steel Alloy Pump Drive Tube
- Heavy Duty Needle Bearing
- Between Stator and Turbine
- Furnace Brazed Turbine
Edelbrock – Street Tunnel Ram Small Block Chevy Intake Manifold (Part No.7110)
from
$631.99
For 3500 to 7500 PRM. Use where low-end torque is not a prime factor. Great for engines with slightly modified heads. HEI ignition will not clear manifold. Street machines, street rods, pro-street and marine.
Product Features:
See More
Product Features:
- For 3500 to 7500 RPM
- Use Where Low-End Torque is Not a Prime Factor
- Great For Engines w/Slightly Modified Heads
- Top Has Vacuum Outlet for Power Brakes
- Will Accept Forward and Sideways Mounted Carbs
- Carburetor Center-to-Center Dimensions 8.875 in
- HEI Ignition Will Not Clear Manifold
- For Street Mach.; Street Rods; Pro-Street; Marine
Mr. Gasket – Intake Manifold Bolts (Part No.957G)
from
$25.99
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes sixteen (16) 3/8 inch-16 x 1-1/4 inch bolts & washers
Product Features:
See More
Product Features:
- Zinc plated Grade 5 steel
- Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
- Ideal For Minimal Space
- 12-Point Head And Flange
- Zinc Plated For Protection
Edelbrock – C-26 Small Block Chevy Dual-Quad Intake Manifold (Part No.5425)
from
$504.99
Product Features:
See More
- Designed for 1500 to 5500 RPM Performance
- Low Profile for Hood Clearance on Most Vehicles
- Air-Conditioning/Front Oil Tube Bosses Included
- Stock Alternator Brackets Do Not Fit
- Use Edelbrock Fuel Line Kit PN[8088] w/Our Carbs
- Carburetor Center-to-Center Dimensions = 6-7/16 in
- Use Edelbrock Linkage Kit PN[7094] w/Our Carbs
- Best Matched with Edelbrock 500 cfm Carburetors
Weiand – X-CELerator; Intake Manifold (Part No.7547-1)
from
$259.99Product Features:
- 2000-6500 RPM Power Band
- Single Plane/Open Plenum Design
- No Provision For Divorced Or Hot Air Choke
- Square Flange Carburetor Mounting
Edelbrock – Intake Manifold Gasket for 1965-1990, Mark IV B/B Chevy, Rec Port (Part No.7208)
from
$30.99
Edelbrock part #7208 Intake Gaskets for 1965-1990, Mark IV 396-402-427-454-555, Rectangular Port 6 Bolt Flange with no crossover allow for optimum flow and performance. Any gasket can create a seal, but a good gasket can do it with less clamping force, an
Product Features:
See More
Product Features:
- 1.82″x2.46″
- Rectangular Port Style
- .060″ Thick
- Two Piece Configuration
- Composite Material
Mr. Gasket – Intake Gasket Set – Standard Duty – Big Block Chevy With Stock Rectangle Ports – 1.75"W X 2.50"H (Part No.108)
from
$29.99
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. Comes complete with front & rear manifold end seals. For original equipment replacement, high performance street, drag race and oval track.
Product Features:
See More
Product Features:
- Manufactured from cellulose/nitrile composition gasket material
- Provides excellent sealing and durability
- Die-cut for an excellent fit
- Can be trimmed if necessary for modified port applications
- Complete with manifold end seals & distributor gaskets if applicable
- For OE replacement, high performance street, drag race and oval track use
FEL-PRO Performance – Lower Intake Manifold Gasket Set: 5 Piece Set (Part No.1210)
from
$44.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
- ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
- REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
- EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
Mr. Gasket – Ultra Seal: Intake Gasket (Part No.5817)
from
$42.99
Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.
Product Features:
See More
Product Features:
- Manufactured from cellulose/nitrile composition gasket material
- Provides excellent sealing and durability
- Silicone beading on both sides of each gasket
- Complete with manifold end seals and distributor gasket
- For OE replacement, high performance street, drag race and oval track use
- Creates Tight Leak proof Seal
FEL-PRO Performance – Lower Intake Manifold Gasket Set: 1 Piece (Part No.1257)
from
$26.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
- ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
- REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
- EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
Mr. Gasket – Intake Manifold Bolts (Part No.6091)
from
$32.09
These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.
Product Features:
See More
Product Features:
- Features 12-point Smaller-than-standard Bolt Head
- Thick Flat Washers Distribute Optimum Clamp Load
- Ideal Use Where Space Is Minimal On Race Manifolds
- Bolts And Washers Zinc Plated For Protection
- Zinc Plated For Protection
Mr. Gasket – Intake Bolt Kit (Part No.5004)
from
$61.99
Finish your custom engine job with these show quality grade 5 chromed bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1-1/4 inch bolts and (12) 3/8 inch AN washers.
Product Features:
See More
Product Features:
- Chrome plated
- Grade 5
- AN washers with no exposed shoulder for a professional appearance
- Ideal For Street Rods/Machines
FEL-PRO Performance – Engine Timing Cover Gasket (Part No.2335)
from
$20.29
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Steel core gasket construction
- Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Timing Cover Gasket Set (Part No.94)
from
$21.79
Mr. Gasket Performance Gaskets are a low density material that conforms well to irregular flange surfaces and has very good crush resistance at high flange pressures. Intended for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit.
Product Features:
See More
Product Features:
- Includes Timing Cover Gasket and Water Pump Gaskets
- Won’t shrink or stick and provide an airtight leak proof seal
- Engineered specifically for big block Chevys and ideal for high performance and race applications
- Ensures optimum torque retention ideal crush resistance and excellent sheer strength using minimal clamp force yet still releases easily
Mr. Gasket – Timing Cover Gasket Set (Part No.90)
from
$21.99
Mr. Gasket Performance Timing Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.
Product Features:
See More
Product Features:
- Manufactured from high-density cork/rubber blend gasket material
- Provides excellent sealing and durability
- For OE replacement, high performance street, drag race and oval track use
Edelbrock – Front Timing Cover Gasket Set #6997 For Small-Block Chevy, With Front Seal (Part No.6997)
from
$17.99
Product Features:
See More
- For Small-Block Chevy
- One Piece Configuration
- Includes Front Cover Gasket & Front Seal
- Includes Necessary Gaskets & Crankshaft Oil Seal
- For Replacement Or Installation
FEL-PRO Performance – Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts (Part No.1002)
from
$68.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
- Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
- Raises combustion sealing force to roughly three times that of standard head gaskets.
- Steel wire rings for the greatest combustion seal strength.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Mls Head Gasket (Part No.3151G)
from
$114.99
Our unique Multi-Layered steel head gasket embossment formation process optimizes the embossment radius, reduces stress points, enhances gasket conformability, and provides uniform clamp load distribution. This all results in superior surface contact between block and cylinder head. All head gasket layers/spacers go through an additional process to significantly reduce forming induced stress. Advantages are reduced brittleness in material, increased flexibility and deformation retention. This stabilizes the gasket, resulting in reduced cylinder bore distortion and improved combustion seal fro the extreme cylinder pressures found in high compression, supercharged and turbocharged applications. A proprietary polymer coating ensures the micro-seal of engine coolant and oil fluids.
Product Features:
See More
Product Features:
- Gasket bore – 4.540 inch: Compressed thickness – .040 inch
- Manufactured from 3-layer premium grade stainless steel and state of the art laser cutting
- Optimized sealing embossments seals extreme cylinder pressure
- Provides excellent stability and reduces cylinder bore distortion.
- Proprietary polymer coating ensures the micro seal of engine coolant and oil fluids.
- Ideal for supercharged, turbocharged, nitrous oxide and extreme compression ratio engines
- For high-performance street, drag race and oval track use
Mr. Gasket – Head Gasket (Part No.1131G)
from
$32.99
Mr. Gasket Steel Shim Cylinder Head Gaskets are for high performance street machines, drag racing and oval track racing. With today’s extreme compression ratios you need stronger more durable gaskets. Mr. Gasket steel shim gaskets are made from .020 inch steel shim stock which is thinner than most composite gaskets increasing engine compression. Stress formed embossments will seal the extreme cylinder pressure.
Product Features:
See More
Product Features:
- Manufactured from .020″ steel shim stock.
- Thinner than composition head gaskets – increases engine compression.
- Stress formed embossments seal extreme cylinder pressures.
- For high performance street, drag race and oval track use.
Mr. Gasket – Head Gasket (Part No.1130G)
from
$32.99
Mr. Gasket Steel Shim Cylinder Head Gaskets are for high performance street machines, drag racing and oval track racing. With today’s extreme compression ratios you need stronger more durable gaskets. Mr. Gasket steel shim gaskets are made from .020 inch steel shim stock which is thinner than most composite gaskets increasing engine compression. Stress formed embossments will seal the extreme cylinder pressure.
Product Features:
See More
Product Features:
- Manufactured from .020″ steel shim stock.
- Thinner than composition head gaskets – increases engine compression.
- Stress formed embossments seal extreme cylinder pressures.
- For high performance street, drag race and oval track use.
Edelbrock – Cylinder Head Gasket Set for Chevrolet (Part No.7310)
from
$58.99
Product Features:
See More
- 4.125 in. Cylinder Bore Diameter
- 0.039 in. Thickness
- 8.7cc Volume
- Charcoal Color
- Two Piece Configuration
FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1047)
from
$72.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
- NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
- SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
- STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
- DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
FEL-PRO Performance – Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts (Part No.1003)
from
$39.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
- NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
- SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
- STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
- DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1004)
from
$52.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
- Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
- Raises combustion sealing force to roughly three times that of standard head gaskets.
- Steel wire rings for the greatest combustion seal strength.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Mls Head Gasket (Part No.3132G)
from
$102.99
Our unique Multi-Layered steel head gasket embossment formation process optimizes the embossment radius, reduces stress points, enhances gasket conformability, and provides uniform clamp load distribution. This all results in superior surface contact between block and cylinder head. All head gasket layers/spacers go through an additional process to significantly reduce forming induced stress. Advantages are reduced brittleness in material, increased flexibility and deformation retention. This stabilizes the gasket, resulting in reduced cylinder bore distortion and improved combustion seal fro the extreme cylinder pressures found in high compression, supercharged and turbocharged applications. A proprietary polymer coating ensures the micro-seal of engine coolant and oil fluids.
Product Features:
See More
Product Features:
- Gasket bore – 4.165 inch: Compressed thickness – .040 inch
- Manufactured from 3-layer premium grade stainless steel and state of the art laser cutting
- Optimized sealing embossments seals extreme cylinder pressure
- Provides excellent stability and reduces cylinder bore distortion.
- Proprietary polymer coating ensures the micro seal of engine coolant and oil fluids.
- Ideal for supercharged, turbocharged, nitrous oxide and extreme compression ratio engines
- For high-performance street, drag race and oval track use
Popular 1999 Chevrolet Blazer Performance Engines Categories
1999 Chevrolet Blazer Performance Engines
Maybe you’re in the middle of a full rebuild of that 1999 Chevrolet Blazer. Maybe you just need a couple of Performance Engines. Either way, Advance Auto Parts has 6 different Performance Engines in our inventory ranging from $20.29 to $709.99. That means you can find the exact parts or products you need to keep that 1999 Chevrolet Blazer running smoothly.
Performance Engines are only as good as their brand. We stock 4 different brands to make sure you have plenty of trusted parts to choose from for your 1999 Chevrolet Blazer. FEL-PRO Performance, Edelbrock, and Mr. Gasket are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!
We know you’ll find the perfect Performance Engines for your 1999 Chevrolet Blazer, but don’t take our word for it – read our customer ratings and reviews and buy with confidence.
So if you’re in the market for aftermarket Performance Engines to keep your 1999 Chevrolet Blazer rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!
Performance Engines Brands To Make Your 1999 Chevrolet Blazer Last
Simple repair, complete replacement, or a full rebuild. No matter the job, your 1999 Chevrolet Blazer demands trusted brand parts and products to keep it running. Many trusted brands of Performance Engines make up Advance Auto Parts’ inventory, and all are ready to help make your Blazer the best it can be. Be sure to browse some of our top Performance Engines brands and parts.
Popular Mr. Gasket Performance Engines
We carry Mr. Gasket parts in our stock across Performance Intake Manifold Hardware categories, plus more. For a 1999 Chevrolet Blazer, our most popular Mr. Gasket Performance Engines include:
FAQs for 1999 Chevrolet Blazer Performance Engines
What are the most purchased Performance Engines for the 1999 Chevrolet Blazer?
Out of 6 Performance Engines for the 1999 Chevrolet Blazer, the most popular in our inventory are:
from
$27.99
This product is not rated
Intake Manifold Gasket for 1985-1995, Chevy V6 200-229-262
Performance Engine Intake Manifold Gaskets
from
$20.29
This product is not rated
Engine Timing Cover Gasket
Performance Engine Timing Cover Gasket Sets
