1987 Ford Aerostar Drivetrains

Below you will find various in-demand Ford Drivetrains, components and accessories for your 1987 Aerostar. Advance Auto Parts has popular Aerostar parts like CV Axles and Joints, Drive Shafts and Axles, Universal Joints and more. You’ll also find aftermarket and OEM Drivetrains for other Aerostar model years including 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997 and more. Select a category of 1987 Ford Aerostar Drivetrains below and start saving instantly.

Popular 1987 Ford Aerostar Drivetrains Categories

Differential Oil

Axle Shaft Universal Joints

Drive Shaft Support Bolts

U-Joints

Rear Differential Cover Gaskets

Differential Open Unit and Components

Differential Covers

U-Joint Strap Kits

Differential Pinion Shaft Lock Bolts

Axle Shaft Bearing Assemblies

Differential Bearings

Differential Axle Shafts

Bearing Pullers

Drive Shaft Bearings

Axle Shaft Seals

Drive Shaft Slip Yoke Sleeves

OE CV Boot Kits

Differential Pinion Pilot Bearings

U-Joint Centering Yokes

Differential Cover Bolts

Axle Shaft Bearings

Transfer Case Output Shaft Seals

Differential Carriers

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Differential Spider Gear Kits

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Differential Clutch Packs

Differential Ring and Pinions

U-Joint U-Bolt Kits

CV Quick Boot Kits

Differential End Yokes

Spindle Lock Nuts

Differential Lock Assemblies

Differential Air System Seal Housings

Rear Differential Pinion Bearings

Differential Spools

Differential Carrier Bearings

Differential Lock Springs

Axle Nuts

Rear Housing Cover Gaskets

Transfer Case Output Shaft Bearings

Differential Pinion Bearing Kits

Axle Shaft Seal Retainers

Drive Shaft Seals

Complete Differentials

Differential Ring Gear Bolts

Bearing Race Drivers

Spindle Lock Nut Thrust Washers

Differential Carrier Bearing Shims

Spindle Retainers

Differential Crush Sleeves

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Gear Install Kits

Differential Cross Pins

Differential Side Gear Thrust Washers

Differential Pinion Bearing Baffles

Differential Pinion Gear Thrust Washers

Differential Drive Pinion Oil Deflectors

Auxiliary Shaft Bearings

Differential Carrier Bolts

Differential Pinion Gear Washers

Spindle Washers

Axle Pinion Repair Sleeves

Differential Pinion Bearing Spacers

Differential Lock Thrust Blocks

Essential Drivetrains for 1987 Ford Aerostars

from

$6.29

This universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles.
Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$13.29

SHAFT SEAL

from

$44.99

Product Features:

Spring kit for Dana Spicer 28, AMC Model 35 IFS, Dana Spicer 44 IFS and Dana Spicer 50 IFS
Allows for installation of positraction or locker

from

$4.29

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$6.99

Product Features:

Inner oil slinger for Dana Spicer 25, 27, 30, 44 and 50

from

$26.99

Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.

Product Features:

Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
Left hand thread

from

$18.99

1310 & 1330 U/joint strap, Dana 30, Dana 44, Model 35, & 9.25″ w/bolts.

Product Features:

u-joint strap kit
Fits Dana Spicer 30 and 44, AMC Model 35 and Chrysler 9.25″
1310 and 1330 u-joint size
Includes two straps and four bolts

from

$123.99

Product Features:

CLUTCH PACK KIT 8.8″ FORD 1 KIT PER UNIT

from

$405.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

Fits standard rotation Dana Spicer 30 without crush sleeve
7.20″ ring gear diameter
26 spline pinion
10 ring gear bolts
4.88 ratio

from

$1303.99

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years.

Product Features:

Fits Dana Spicer 30 with 27 spline axles
3.73 and up ratio only
Forged case and 8620 internals for added strength
Works with a variety of air delivery systems
Assembled in the USA

from

$6.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$5.99

This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$188.99

Yukon replacement standard open carrier case for Dana 30, 3.54 & down, 1.810″ tall. If purchasing this case for a D30 JK front, you will need to also purchase spider gear set YPKD30-S-27.

Product Features:

Standard open carrier case
Fits Dana Spicer 30
3.54 and down ratio only
Does not include spider gears

from

$121.99

Yukon replacement yoke for Dana 30, 44, 50, and Dana 300 with 26 spline and a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 44
26 spline
1310 u-joint size
3.219″ snap ring span
1.062″ cap diameter
Outside snap ring design
U-bolt style

from

$234.99

Yukon 1541H alloy 5 lug left hand rear axle for 7.5″ and 8.8″ Ford Ranger (right hand for Aerostar) with a length of 29-5/32″ inches and 28 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a C-clip axle.

Product Features:

Fits 1983-1992 Ford 7.5″ rear in Ford Ranger
Left hand side
28 spline
29 5-32″ long
5 lug

from

$3.99

Replacement pinion nut washer for Dana 25, 27, 30, 36, 44 & 53.

Product Features:

Pinion nut washer for Dana Spicer 25, 27, 30, 44 and 50

from

$3.93

Dorman’s Spindle Nut is manufactured for high corrosion resistance and a long service life. Depending on the application, it is also available in a kit that includes the nut, washer, and retainer.

Product Features:

Direct replacement for a proper fit every time
High quality steel construction
Conveniently available in many styles and in packs of different quantities
Dorman’s Spindle Nuts are constructed to strict engineering quality standards

from

$10.99

Dana 25, Dana 27, & Dana 30 side gear Thrust washer.

Product Features:

Side gear thrust washer for Dana Spicer 25, 27, 30 and AMC Model 35
1.560″ I.D.
Fits standard open differentials only

from

$111.99

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke.
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts.
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$155.99

Yukon replacement standard open spider gear kit for Dana 30 with 27 spline axles and with or without quick disconnect. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fit Dana Spicer 30 open differential with 27 spline axles
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$11.79

Formulated to meet the specific requirements of Toyota, Lexus, and scion vehicles equipped with conventional (non-CVT) transmissions that require the use of ATF T-IV. Recommended for service-fill in all Toyota, Lexus, and Scion automatic transmissions where ATF T-IV is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. IDEMITSU is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. IDEMITSU application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.

Product Features:

Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
Provides superior cleanliness, maintaining the transmission free of sludge and varnish deposits
Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
Advanced anti-wear technology provides maximum protection to gears and bearings
Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking

from

$10.49

Product Features:

SOLID SPACER FORD 8.8″ & 9″

from

$35.99

Product Features:

MINI INSTALL KIT FORD 8.8

from

$4.99

Product Features:

Oil baffle for Dana Spicer 30, Dana Spicer 44 IFS, Dana Spicer 50, AMC Model 35 IFS

from

$201.99

Product Features:

Fits standard rotation Dana Spicer 30
Finned polished aluminum

from

$138.99

Product Features:

Fits standard rotation Dana Spicer 30
Steel

from

$9.29

Our Spindle Nut is manufactured for high corrosion resistance and a long service life. Depending on the application, it is also available in a kit that includes the nut, washer, and retainer.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$3.99

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Upgrade your 1987 Ford Aerostar with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 1987 Ford Aerostar, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Ford or enhancing its overall performance, Drivetrains are key to keeping your Aerostar functioning at its best. At Advance Auto Parts, we offer a wide selection of 256 Drivetrains for the 1987 Ford Aerostar, designed to meet your needs without breaking the bank. From CV Axles and Joint replacements to Drive Shafts and Axles upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 1987 Ford Aerostar at great prices. Our Drivetrains inventory for this model ranges from just $0.99 to $1,566.99, with an average price of $131.02. Our 256 Drivetrains in stock come from 17 trusted brands, so you’re sure to find the right part for your 1987 Ford Aerostar without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1987 Ford Aerostar, we stock popular OEM and aftermarket Drivetrains from top names like Moog, Driveworks, Dorman, and more. Moog Drivetrains start at just $11.99 and boast an impressive 4 stars average rating from customers. Driveworks and Dorman also bring quality to the table, with Drivetrains available starting at $3.49, and at an average 4 stars rating. With 868 customer reviews and counting, our 1987 Ford Aerostar Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1987 Ford Aerostar is always ready to roll. We’re committed to providing you with everything you need to keep your Aerostar in top shape, all in one place. Start shopping confidently below for your 1987 Ford Aerostar!

Best-Selling CV Axles and Joints for 1987 Ford Aerostars

Enhance the driving experience in your Ford with 4 quality CV Axles and Joint components, starting at $23.99.

show more show less

from

$29.49

This CV joint boot kit contains the parts required to repair the CV joint on specified vehicles without removing the joint itself. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this CV joint boot kit contains the parts required to repair the CV joint on specified vehicles without removing the joint itself.
Ideal solution – this kit is a reliable replacement for original components that have failed due to wear.
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$35.99

Direct replacement – this CV joint boot kit contains the parts required to repair the CV joint on specified vehicles without removing the joint itself.
Ideal solution – this kit is a reliable replacement for original components that have failed due to wear.
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$23.99

Our CV Joint Boots provide various methods of eliminating the removal of the CV joint during installation. Uni-Fit boots can be stretched over the CV Joint and Quick Boots come in halves.

Product Features:

Direct replacement – this CV joint boot kit contains the parts required to repair the CV joint on specified vehicles without removing the joint itself.
Ideal solution – this kit is a reliable replacement for original components that have failed due to wear
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$42.99

Direct replacement – this CV joint boot kit contains the parts required to repair the CV joint on specified vehicles without removing the joint itself.
Ideal solution – this kit is a reliable replacement for original components that have failed due to wear.
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Most Popular 1987 Ford Aerostar Drive Shafts and Axles

Customize your Ford with 31 Drive Shafts and Axles products like Axle Shaft Seals, Axle Shaft Universal Joints, and Axle Shaft Bearings, all priced under $883.99.

show more show less

from

$5.49

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$20.29

This drive shaft bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this engine mount bolt matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this drive shaft bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$35.99

You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you’re getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.

from

$18.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$4.29

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$11.49

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$33.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$16.49

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$21.79

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$42.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1563TAV axle bearing and seal kit, TorringtonBrand, 2.250″ OD, 1.400″ ID. This axle bearing & seal kit services one side only.

Product Features:

Includes axle bearing and seal
Services one side
Torrington Brand
2.250″ O.D.
1.400″ I.D.

from

$37.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$34.99

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$111.99

Direct replacement – this differential end yoke matches the fit and construction of the original yoke.
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts.
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$17.26

Spindle Nut

from

$8.99

Ford 7.5″ C/clip, TracLoc & standard Open.

Product Features:

c-clip for Ford 7.5″
Fits standard open and Trac Loc applications
Not compatible with Auburn Gear positraction

from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings

from

$146.99

Yukon replacement yoke for Dana 30, 44, and 50 with 26 spline and a 1330 U/joint size. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 30 and 44
26 spline
1330 u-joint size
Outside snap ring design
3.625″ snap ring span
1.062″ cap diameter
Strap style

from

$125.99

Yukon replacement yoke for Dana 30, 44, and 50 with 26 spline and a 1330 U/joint size. 3.625″ snap ring span, 1.125″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 44
26 spline
1330 u-joint size
3.625″ snap ring span
1.125″ cap diameter
Outside snap ring design
U-bolt style

from

$289.99

Yukon replacement yoke for Dana 30, 44, and 50 with 26 spline and a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 30 and 44
26 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
Strap style

from

$182.99

Replacement redi-sleeve yoke saver for Dana 25, Dana 27, Dana 30, Dana 44, Dana 50 .Yukon Mighty seal.

Product Features:

Pinion Redi-sleeve
Fits Dana Spicer 25, 27, 30, 4 and 50

from

$86.99

Drive Shaft End Yoke

from

$64.99

AXLE SHAFT REPAIR BE

from

$47.99

7.5″ C/clip, AG positraction

Product Features:

C-clip
Fits Ford 7.5″ with Auburn Gear positraction

from

$44.99

SPICER U-JOINT

from

$40.99

BEARING

from

$36.49

AXLE BEARING

from

$12.70

Axle Seal

from

$6.99

Axle seal for 5707 OR 1563 bearing.Yukon Mighty seal.

Product Features:

Rear axle seal
2.250″ O.D.

from

$5.19

SHAFT SEAL

from

$3.93

Direct replacement for a proper fit every time
High quality steel construction
Conveniently available in many styles and in packs of different quantities
Dorman’s Spindle Nuts are constructed to strict engineering quality standards

from

$1.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

Top Picks for 1987 Ford Aerostar Universal Joints

Upgrade Ford Aerostars with top-quality Universal Joints parts, including 23 OEM and aftermarket selections for your 1987 model.

show more show less

from

$28.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles.

from

$19.99

Backed by superior materials and rigorous testing, MOOG Heavy Duty universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST — Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE — Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN — Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR — Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE — Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$11.99

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

For U-Joints 355, 372 & 534G
Contains two 1.81″ bolt center clamps and four 5/16-24 x 1-5/16″ cap screws

from

$32.99

Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$32.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$15.99

DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$6.29

Direct replacement – this universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles.
Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$26.99

Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
GREASABLE DESIGN — Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT — Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$5.29

Universal Joint

from

$18.99

1310 & 1330 U/joint strap, Dana 30, Dana 44, Model 35, & 9.25″ w/bolts.

Product Features:

u-joint strap kit
Fits Dana Spicer 30 and 44, AMC Model 35 and Chrysler 9.25″
1310 and 1330 u-joint size
Includes two straps and four bolts

from

$44.99

Yukon 1310 U/Joint with zerk fitting on cross. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring.

from

$59.99

Yukon 1310 to 1330 adapter U/Joint. The 1310 side has a 3.219″ span and 1.062″ caps. The 1330 side has a 3.625″ span and 1.062″ caps. Both sides are outside snap ring.

from

$34.99

1310 U-bolts, 5/16″ x 1-3/8″ Dana 30, Dana 44, 8.2″, 12P, 12T, VET, Model 20.

Product Features:

u-joint u-bolt kit
Fits AMC Model 20, Dana Spicer 30 and 44, GM 8.2″, 12 bolt passenger car and truck and 1963-1979 Corvette
1310 u-joint size
Includes two u-bolts and four nuts

from

$27.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$78.99

Yukon 1350 to 1410 conversion u/joint.

from

$27.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$109.99

Yukon 1310 to Mechanics 3R adapter U/Joint.

from

$121.99

Fits Dana Spicer 44
26 spline
1310 u-joint size
3.219″ snap ring span
1.062″ cap diameter
Outside snap ring design
U-bolt style

from

$53.99

1330 Yukon Lifetime U/Joint. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring.

from

$57.99

1310 Yukon Lifetime U/joint. 1.718″ snap ring span, 1.062″ cap diameter. Inside snap ring.

from

$111.99

Yukon 1350 to Mechanics 3R adaptor U/joint.

from

$29.99

from

$15.99

1330 U/joint U-bolts, 5/16″ X 1-9/16″, (7260 & 7290 BILLET).

Product Features:

u-joint u-bolt kit
Fits AMC Model 20, Dana Spicer 30 and 44, GM 8.2″, 12 bolt passenger car and truck and 1963-1979 Corvette
1330 u-joint size
Includes two u-bolts and four nuts

In-Demand Transfer Cases for 1987 Ford Aerostars

Select from 8 premium Transfer Cases parts for your 1987 Ford Aerostar, with prices ranging from $6.49 to $19.29.

show more show less

from

$15.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$10.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$6.49

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$19.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$18.99

CONE

from

$15.49

BEARING

from

$13.29

SHAFT SEAL

from

$11.29

CUP

Most Sold 1987 Ford Aerostar Differentials

Explore our best-selling Ford parts for the 1987 Aerostar among 184 OEM and aftermarket options starting from $0.99.

show more show less

from

$7.49

High-quality Differential Component Shim

Product Features:

SHIM KIT FITS-8.25-F7.5-AMC20-GM0

from

$112.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

FORD 7.5″ MASTER BEARING KIT

from

$350.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.Powertrax® = Extreme Traction Systems!

from

$444.99

from

$23.29

National« has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today┐s vehicles.

Product Features:

Design type: spring loaded; multi-lip
Temperature range: -20░F to 300░F / -29░C to 49░C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$10.49

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$23.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$5.99

Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$6.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$6.49

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

from

$109.99

DANA-30 FORD MASTER BRG KIT

from

$176.99

Product Features:

DANA-30 R/P 4.88 STD

from

$4.79

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$57.99

3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.

Product Features:

Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive

from

$6.99

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features:

35 spline
8 x 3.96″ bolt pattern
Cut to length design fits 40″-43.5″ applications
Fits Dana Spicer 60, 70 and 80

from

$5.99

This differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles.
Required replacement – when servicing the differential
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$11.99

Replacement ring gear bolt for Model 35, Dana 25, 27, 30 & 44. 3/8″ x 24.

Product Features:

Ring gear bolt for Dana Spicer 25, 27, 30, 44 and AMC Model 35
3/8″ x 24 thread

from

$12.99

Product Features:

Cover gasket
Fits Dana Spicer 30

from

$9.99

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
1/2″ head

from

$9.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$15.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$4.99

Product Features:

Oil baffle for Dana Spicer 30, Dana Spicer 44 IFS, Dana Spicer 50, AMC Model 35 IFS

from

$16.99

Product Features:

Brand may vary by location

from

$7.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$10.99

Dana 25, Dana 27, & Dana 30 side gear Thrust washer.

Product Features:

Side gear thrust washer for Dana Spicer 25, 27, 30 and AMC Model 35
1.560″ I.D.
Fits standard open differentials only

from

$9.99

Crush Sleeve for Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9 3/8″, 9″ & 9.75″. .480″ long.

Product Features:

Crush sleeve for AMC Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9″ and 9.75″
0.480″ tall

from

$9.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

from

$8.99

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

from

$5.99

Ford 7.5″ & 8.8″ ring gear bolt, standard Open & TracLoc. 7/16″ x 20.

Product Features:

Ring gear bolt for Ford 7.5″ and 8.8″
7/16″ x 20

from

$7.99

Pinion nut for Ford 7.5″, 8″, 8.8″, 9 3/8″ & 9″. 1 1/6″ socket, 3/4″ x 20 thread.

Product Features:

Pinion nut for Ford 7.5″, 8″ and 9″
3/4″ x 20 thread
1 1/6″ socket

from

$6.99

Pinion nut for Dana Spicer 25, 27, 30, 44, 50 and GM 7.75″
3/4″ x 16 thread

from

$1.99

Product Features:

Ford 7.5″, 8.8″ Ring Gear Bolt

from

$17.99

Replacement pinion seal for Dana 25, Dana 27, Dana 30, D36, Dana 44, & Dana 50 .Yukon Mighty seal.

Product Features:

Pinion seal
Fits Dana Spicer 25, 27, 30, 40 and 50

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

from

$156.99

Spindle nut washer for Dana 28, ’92 & down. This replaces Spicer part number 40075.

Product Features:

Spider gear kit
Fit Ford 7.5″ open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$38.49

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$27.99

8.25″ IFS, 8.5″, 12P, 7.5″ F, 8.8″ F, 8.25″ Chrysler pinion shim kit.

Product Features:

Pinion depth shims for GM 8.25″ IFS, 8.5″, 8.6″, 12 bolt passenger car, Ford 7.5″ and 8.8″, Chrysler 8.25″

from

$7.99

Dana 28 & Dana 30 pinion gear Thrust washer. Also fits AMC Model 35 with 1.560″ side gear bore only.

Product Features:

Pinion gear thrust washer for Dana Spicer 25, 27 and 30

from

$99.99

DiffrlCover

from

$3.29

from

$164.99

Yukon replacement standard open carrier case for Dana 30, 3.73 & up, 1.943″ tall. If purchasing this case for a D30 JK front, you will need to also purchase spider gear set YPKD30-S-27.

Product Features:

Standard open carrier case
Fits Dana Spicer 30
3.73 and up ratio only
Does not include spider gears

from

$99.99

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

Includes three quarts of Redline Shockproof oil

from

$137.99

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil

from

$96.99

2 piece solid spacer for Ford 8.8 and 7.5.

Product Features:

Crush sleeve eliminator kit for Ford 7.5″ and 8.8″

from

$69.99

Design type: spring loaded; multi-lip
Temperature range: -100°F to 450°F; -73°C to 232°C
Resistant to hydrocarbon/oxygenate blends and provides superior performance
Provides excellent dry running capabilities, low coefficient of friction and excellent resistance to chemicals
Delivers quality and reliable performance for every type of repair

from

$18.99

Product Features:

CARRIER SHIM – DANA 30

from

$16.99

Product Features:

PINION SHIM-DANA 30,35.50

from

$6.99

Product Features:

D30 PRE-LOAD SPACER (SHIM PACK)

Top-Rated Drivetrains Brands For Your 1987 Ford Aerostar

Shop for the best-rated brands offering Drivetrains and other products for your 1987 Ford Aerostars. Below you’ll find some of our best rated Drivetrains from Moog, Driveworks, and Dorman, and more. Drivetrains from these brands that fit a 1987 Aerostar start at just $3.49 and are rated as high as 4 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular Moog 1987 Ford Aerostar Drivetrains

When it comes to maintaining or upgrading your 1987 Ford Aerostar, using quality Drivetrains is essential to ensure durability and a perfect fit. Moog ticks all of those boxes. We offer a wide selection of Moog Drivetrains, specifically designed for the 1987 Ford Aerostar. With over 7 Moog brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $11.99, with an average price of just $25.85. Plus, with over 184 customer reviews and an average rating of 4 stars, you can trust that our Moog Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from
$19.99

(82)

Greaseable Premium Universal Joint

“Great product”

from
$27.99

This product is not rated

Greaseable Super Strength Universal Joint

“”

from
$27.99

This product is not rated

Non-Greaseable Super Strength Universal Joint

“”

Popular Driveworks 1987 Ford Aerostar Drivetrains

Driveworks auto parts is one of the highest quality Drivetrain brands in the market. Any 1987 Ford Aerostar owner should feel confident when installing genuine Driveworks parts in their vehicle. To ensure the best fit and performance for your 1987 Aerostar, Advance Auto Parts carries a full inventory of 11 Driveworks Drivetrains. Plus you will be keeping your Ford in peak condition while saving money because prices on these Driveworks Drivetrains range from $4.29 to $19.29, plus, with more than 98 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from
$6.49

This product is not rated

Taper Bearing Cup

“”

from
$7.29

This product is not rated

Taper Bearing Cup

“”

from
$16.99

This product is not rated

Tapered Roller Bearing

“”

FAQs for 1987 Ford Aerostar Drivetrains

Which Drivetrains are best-sellers for 1987 Ford Aerostars?

Out of 256 Drivetrains that fit 1987 Ford Aerostars, the following parts are the top sellers:

Universal Joint (10265714) – $15.99
Oil Seal (5441617) – $5.49
Non-Greaseable Super Strength Universal Joint (10087061) – $32.99

What’s the price range for 1987 Ford Aerostar Drivetrains?

Drivetrain prices for the 1987 Ford Aerostar start at $0.99 and go up to $1,566.99 for the most premium parts.

What’s the average price of a Drivetrain for a 1987 Ford Aerostar?

The average price for Drivetrains for the 1987 Ford Aerostar is $131.02. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Ford Aerostar model years?

Yes, we currently carry Drivetrains for 11 model years of Ford Aerostars between 1986 and 1997. Drivetrains are bought most frequently for the following model years: 1997, 1996, 1995, 1994, 1993, 1992, 1991, 1990, and 1989.

What are the cheapest Drivetrains for my 1987 Ford Aerostar?

The cheapest 1987 Ford Aerostar Drivetrains we carry in stock are:

Differential Ring Gear Bolt (10282257) – $0.99
Ring Gear Bolt (20520509) – $1.99
Axle Seal (10593098) – $1.99
Differential Cross Shaft (10282201) – $2.79
Differential Crush Sleeve (10282338) – $2.99

What are the top-rated Drivetrains that fit the 1987 Ford Aerostar?

Out of 868 reviews by customers, our 1987 Ford Aerostar Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 1987 Ford Aerostar and their top-rated products:

Universal Joints
- Universal Joint (10855076) – $28.99
- Greaseable Premium Universal Joint (10086900) – $19.99
- Universal Joint Strap Kit (10086946) – $11.99
Spindles
- Universal Joint (10855076) – $28.99
- Greaseable Premium Universal Joint (10086900) – $19.99
- Universal Joint Strap Kit (10086946) – $11.99
Differentials
- Universal Joint (10855076) – $28.99
- Greaseable Premium Universal Joint (10086900) – $19.99
- Universal Joint Strap Kit (10086946) – $11.99

What types of Drivetrains do you sell for my 1987 Ford Aerostar?

As of 2/5/25, these are some of the most in-demand types of Drivetrains for a 1987 Ford Aerostar:

Can I get help with 1987 Ford Aerostar Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Ford Drivetrains and more.

What is your return policy for Ford Aerostar Drivetrains?

Advance Auto Parts keeps returns simple. For new Ford Aerostar Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1987 Ford Aerostar Drivetrains

Dorman – Help – U-Joint Bolt Kit (Part No.81004)

FAG US – SHAFT SEAL (Part No.SS2480)

Yukon Gear – Spring Kit For Dana 28, Model 35IFS, Dana 44IFS & Dana 50IFS With Grizzly, Detroit, Tt Or Pl (Part No.33263)

Driveworks – Oil Seal (Part No.S-2146)

Yukon Gear – Dana 25 / 27 / 30 / 44 / 50 Inner Oil Slinger Replacement (Part No.33012)

Yukon Gear – Dana 30 & Dana 44 Power Lok Bolt, Left Hand, & 8.75" Chrysler & 55P (Part No.33234)

Yukon Gear – 1310 & 1330 U/Joint Strap, Dana 30, Dana 44, Model 35, & 9.25" With Bolts (Part No.41195)

Motive Gear – Differential Clutch Pack (Part No.F8.8CPK)

Yukon Gear – High Performance Ring & Pinion Replacement Gear Set For Dana 30 In A 4.88 Ratio (Part No.24022)

Yukon Gear – Zip Locker For Dana 30 With 27 Spline Axles, 3.73 & Up (Part No.34016)

Felpro – Differential Cover Gasket (Part No.RDS 55393)

Dorman – Help – Differential Shaft Lock Bolt (Part No.81048)

Yukon Gear – Replacement Standard Open Carrier Case For Dana 30, 3.54 & Down (Part No.20025)

Yukon Gear – Replacement Yoke For Dana 30, 44, 50, And 300 With 26 Spline And A 1310 U/Joint Size (Part No.41018)

Yukon Gear – 1541H Alloy 5 Lug Left Hand Rear Axle For 7.5" And 8.8" Ford Ranger (Part No.21181)

Yukon Gear – Dana 25 / 27 / 30 / 36 / 44 / 53 Pinion Nut Washer Replacement (Part No.33163)

Dorman – Axle Spindle Nut (Part No.K4030212888DOR)

Yukon Gear – Dana 30 Side Gear Thrust Washer (Part No.33284)

Dorman – Differential Pinion Yoke Assembly (Part No.697-542)

Yukon Gear – Replacement Standard Open Spider Gear Kit For Dana 30 With 27 Spline Axles (Part No.16073)

Idemitsu – Type TLS Automatic Transmission Fluid – 1 qt (Part No.10106-042K)

Motive Gear – Differential Pinion Solid Spacer Kit w/Shims (Part No.4104)

Motive Gear – Differential Gear Install Kit (Part No.F8.8IK)

Yukon Gear – Replacement Oil Baffle For Model 35 IFS Front, Dana 25, 27, 30, 44 IFS & Disconnect And Dana 50 (Part No.33002)

Yukon Gear – Polished Aluminum Replacement Cover For Dana 30 Standard Rotation (Part No.32021)

Yukon Gear – Steel Cover For Dana 30 Standard Rotation Front (Part No.32316)

Dorman – Spindle Nut (Part No.05170)

Dorman – Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (sold by each) (Part No.615-072)

Dorman – Uni-Fit C.V. Joint Boot Kit Outer up to 3.58 In. Diameter (Part No.614-001)

Dorman – Uni-Fit C.V. Joint Boot Kit Inner up to 3.58 In. Diameter (Part No.614-002)

Dorman – Help – Universal C.V. Joint Boot Kit Front Outer (Part No.03680)

Dorman – Split CV Boot – With Quick Drying Adhesive (Part No.614-700)

Driveworks – Oil Seal (Part No.S-8660S)

Dorman – Help – Driveshaft Flange Bolts (Part No.80992)

Spicer – Universal Joint (Part No.5-1310X)

National – Multi Purpose Seal (Part No.2146)

Driveworks – Oil Seal (Part No.S-2146)

National – Multi Purpose Seal (Part No.1990)

National – Shaft Repair Sleeve (Part No.99106)

Driveworks – Axle Repair Bearing (Part No.S-RP-5707)

National – Bearings (Part No.HM88649)

Yukon Gear – R1563Tav Rear Axle Bearing And Seal Kit (Part No.10004)

National – Bearings (Part No.307-L)

National – Shaft Repair Sleeve (Part No.99166)

Dorman – Differential Pinion Yoke Assembly (Part No.697-542)

Dorman – Spindle Nut (Part No.K1002831650DOR)

Yukon Gear – Ford 7.5" C/Clip, Tracloc & Standard Open (Part No.33080)

Yukon Gear – The Carrier Bearing Puller (Part No.56072)

Yukon Gear – Replacement Yoke For Dana 30, 44, And 50 With 26 Spline And A 1330 U/Joint Size (Part No.41019)

Yukon Gear – Replacement Yoke For Dana 30, 44, And 50 With 26 Spline And A 1330 U/Joint Size (Part No.41020)

Yukon Gear – Replacement Yoke For Dana 30, 44, And 50 With 26 Spline And A 1350 U/Joint Size (Part No.41021)

Yukon Gear – Replacement Redi-Sleeve Yoke Saver For Dana 25, Dana 27, Dana 30, Dana 44, Dana 50 (Part No.30222)

Spicer – Drive Shaft End Yoke (Part No.2-4-6111X)

FAG US – AXLE SHAFT REPAIR BE (Part No.DR0148K)

Yukon Gear – 7.5" C/Clip, Ag Positraction (Part No.33079)

Spicer – SPICER U-JOINT (Part No.5-1310-1X)

FAG US – BEARING (Part No.6206-2RSR)

FAG US – AXLE BEARING (Part No.FC67147)

Autopart International Inc – Axle Seal (Part No.K40212055475API)

Yukon Gear – Axle Seal For 5707 Or 1563 Bearing (Part No.30196)

FAG US – SHAFT SEAL (Part No.SS2468)

Dorman – Axle Spindle Nut (Part No.K4030212888DOR)

Pro-King – Axle Seal (Part No.721A074)

Spicer – Universal Joint (Part No.5-153X)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.369)

MOOG Driveline Products – Universal Joint Strap Kit (Part No.530-10)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.269)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.280)

Driveworks – Universal Joint (Part No.DW-369)

Dorman – Help – U-Joint Bolt Kit (Part No.81004)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.430)

Neapco – Universal Joint (Part No.1-5900)

Yukon Gear – 1310 & 1330 U/Joint Strap, Dana 30, Dana 44, Model 35, & 9.25" With Bolts (Part No.41195)

Yukon Gear – 1310 U/Joint With Zerk Fitting On Cross (Part No.42008)

Yukon Gear – 1310 To 1330 Adapter U/Joint (Part No.42005)

Yukon Gear – Dana 44, 8.2", 12P, 12T, Vet, And Model 20 U-Bolts (Part No.41198)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.230)

Yukon Gear – 1350 To 1410 Conversion U/Joint (Part No.42006)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.255)