1989 Ford Aerostar Drivetrains

Below you will find various in-demand Ford Drivetrains, components and accessories for your 1989 Aerostar. Advance Auto Parts has popular Aerostar parts like Drive Shafts and Axles, Differentials, Transfer Cases and more. You’ll also find aftermarket and OEM Drivetrains for other Aerostar model years including 1988, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997 and more. Select a category of 1989 Ford Aerostar Drivetrains below and start saving instantly.

Please Select your Vehicle to See Exact Fit Parts

Popular 1989 Ford Aerostar Drivetrains Categories

Differential Oil

Axle Shaft Universal Joints

Drive Shaft Support Bolts

U-Joints

Transfer Case Gaskets

Rear Differential Cover Gaskets

Differential Open Unit and Components

Differential Covers

U-Joint Strap Kits

Differential Pinion Shaft Lock Bolts

Axle Shaft Bearing Assemblies

Differential Bearings

Differential Axle Shafts

Drive Shaft Bearings

Axle Shaft Seals

Drive Shaft Slip Yoke Sleeves

OE CV Boot Kits

Differential Pinion Pilot Bearings

U-Joint Centering Yokes

Differential Cover Bolts

Axle Shaft Bearings

Transfer Case Output Shaft Seals

Differential Carriers

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Differential Spider Gear Kits

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Differential Clutch Packs

Differential Ring and Pinions

U-Joint U-Bolt Kits

CV Quick Boot Kits

Differential End Yokes

Spindle Lock Nuts

Differential Lock Assemblies

Differential Air System Seal Housings

Differential Spools

Differential Carrier Bearings

Differential Lock Springs

Rear Housing Cover Gaskets

Differential Pinion Bearing Kits

Axle Shaft Seal Retainers

Differential Seals

Complete Differentials

Differential Ring Gear Bolts

Bearing Race Drivers

Spindle Lock Nut Thrust Washers

Differential Carrier Bearing Shims

Input Shaft Seals

Spindle Retainers

Differential Crush Sleeves

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Gear Install Kits

Differential Cross Pins

Differential Side Gear Thrust Washers

Differential Pinion Bearing Baffles

Differential Pinion Gear Thrust Washers

Axle Shaft Studs

Differential Drive Pinion Oil Deflectors

Differential Carrier Bolts

Spindle Washers

Drive Shaft End Yokes

Differential Pinion Bearing Spacers

Differential Bolts

Differential Lock Thrust Blocks

Axle Pinion Repair Sleeves

Essential Drivetrains for 1989 Ford Aerostars

from

$13.99

Product Features:

O-ring for seal housing
Fits Dana Spicer 30 and AMC Model 35

from

$10.99

Replacement pinion nut for Model 20 & 35, Dana 30 JK, 44 JK front, Ford 10.25″, 10.5″ & some 9.75″. 7/8-20 thread, 1 1/8 socket.

Product Features:

Pinion nut for Jeep JK front, Jeep Liberty front, Ford 9.75″, 10.25″, 10.5″ and AMC Model 20 and Model 35
7/8″ x 20 thread
1 1/8″ socket

from

$10.49

Product Features:

SOLID SPACER FORD 8.8″ & 9″

from

$37.99

DIFF COVER KIT

from

$22.49

This drive shaft bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this engine mount bolt matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this drive shaft bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$639.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect. Does not fit Std. JK Carrier. Use YC D706008

Product Features:

Fits Dana Spicer 30 with 27 spline axles
Made from 9310 steel for added strength
Replaces the spiders in a standard carrier case

from

$175.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. Includes side seals. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

Fits AMC Model 35 IFS
Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

from

$5.19

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$6.99

Axle seal for 5707 OR 1563 bearing.Yukon Mighty seal.

Product Features:

Rear axle seal
2.250″ O.D.

from

$38.99

You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.

from

$6.79

This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$8.99

Ford 7.5″ C/clip, TracLoc & standard Open.

Product Features:

c-clip for Ford 7.5″
Fits standard open and Trac Loc applications
Not compatible with Auburn Gear positraction

from

$19.49

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$279.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 30 rear
Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

from

$188.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M86610 race
All steel construction

from

$4.99

Product Features:

Oil baffle for Dana Spicer 30, Dana Spicer 44 IFS, Dana Spicer 50, AMC Model 35 IFS

from

$59.99

Product Features:

Super carrier shim kit for Ford 7.5″, GM 7.5″, 7.625″, 7.6″ IFS, 7.6″ IRS, 7.75″, 8.2″, 8.2″ Buick, Oldsmobile and Pontiac and GM 8.5″ front and rear
Interlocking design makes installation much easier

from

$67.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 in

Product Features:

Trac Loc spring
Fits Ford 7.5″

from

$18.99

Product Features:

CARRIER SHIM – DANA 30

from

$125.99

Yukon replacement yoke for Dana 30, 44, and 50 with 26 spline and a 1330 U/joint size. 3.625″ snap ring span, 1.125″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 44
26 spline
1330 u-joint size
3.625″ snap ring span
1.125″ cap diameter
Outside snap ring design
U-bolt style

from

$31.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.

Product Features:

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$6.49

This differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles
Required replacement – when servicing the differential
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$289.99

This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$26.99

Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.

Product Features:

Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
Left hand thread

from

$230.99

Product Features:

FRD 10BLT 8.8 R/P 3.73 MGP

from

$10.99

Standard Open & TracLoc pinion gear thrust washer for 7.5″ Ford.

Product Features:

Pinion gear thrust washer
Fits Ford 7.5″

from

$34.49

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$109.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.2″ & 8.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits GM 7.5″, 7.625″ 8.2″ and 8.5″
Includes carrier bearings and races and “super” carrier shim kit

Upgrade your 1989 Ford Aerostar with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 1989 Ford Aerostar, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Ford or enhancing its overall performance, Drivetrains are key to keeping your Aerostar functioning at its best. At Advance Auto Parts, we offer a wide selection of 241 Drivetrains for the 1989 Ford Aerostar, designed to meet your needs without breaking the bank. From Drive Shafts and Axle replacements to Differentials upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 1989 Ford Aerostar at great prices. Our Drivetrains inventory for this model ranges from just $1.29 to $1,566.99, with an average price of $131.95. Our 241 Drivetrains in stock come from 18 trusted brands, so you’re sure to find the right part for your 1989 Ford Aerostar without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1989 Ford Aerostar, we stock popular OEM and aftermarket Drivetrains from top names like National, Dorman, Driveworks, and more. National Drivetrains start at just $11.99 and boast an impressive 4.3 stars average rating from customers. Dorman and Driveworks also bring quality to the table, with Drivetrains available starting at $3.49, and at an average 4.2 stars rating. With 861 customer reviews and counting, our 1989 Ford Aerostar Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1989 Ford Aerostar is always ready to roll. We’re committed to providing you with everything you need to keep your Aerostar in top shape, all in one place. Start shopping confidently below for your 1989 Ford Aerostar!

Best-Selling Drive Shafts and Axles for 1989 Ford Aerostars

Enhance the driving experience in your Ford with 17 quality Drive Shafts and Axle components, starting at $5.19.

show more show less

from

$22.49

Direct replacement – this engine mount bolt matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this drive shaft bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$38.99

from

$7.99

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$24.99

Manufactured with premium-grade steel, National cylindrical bearings are designed and engineered to meet OE specifications.

Product Features:

STRONG AND DURABLE: Controlled heat treatment process for strength and durability
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for durability and performance
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
Professional technicians know they can depend on National

from

$18.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$19.99

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$42.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1563TAV axle bearing and seal kit, TorringtonBrand, 2.250″ OD, 1.400″ ID. This axle bearing & seal kit services one side only.

Product Features:

Includes axle bearing and seal
Services one side
Torrington Brand
2.250″ O.D.
1.400″ I.D.

from

$6.99

Ford 7.5″, 8″, 8.8″, & 9″ axle stud.

Product Features:

Axle stud for Ford 7.5″, 8.8″ and 9″
1/2″ x 20 thread
1 7/8″ long
29/64″ shoulder length

from

$8.99

Ford 7.5″ C/clip, TracLoc & standard Open.

Product Features:

c-clip for Ford 7.5″
Fits standard open and Trac Loc applications
Not compatible with Auburn Gear positraction

from

$121.99

Yukon replacement yoke for Dana 30, 44, 50, and Dana 300 with 26 spline and a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 44
26 spline
1310 u-joint size
3.219″ snap ring span
1.062″ cap diameter
Outside snap ring design
U-bolt style

from

$314.99

Yukon flange yoke for Ford 7.5″ passenger and truck (4.3″ OD). All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 7.5″
28 spline
Round companion flange
4.3″ O.D.

from

$182.99

Replacement redi-sleeve yoke saver for Dana 25, Dana 27, Dana 30, Dana 44, Dana 50 .Yukon Mighty seal.

Product Features:

Pinion Redi-sleeve
Fits Dana Spicer 25, 27, 30, 4 and 50

from

$86.99

Spicer end yokes deliver the same quality and reliability you expect from your original equipment parts. That is because they are OE parts, manufactured to the same standards and specifications as the end yokes that were installed in your vehicle in the first place.

Product Features:

Genuine OE quality. Tested and proven.
Built to meet OE standards set by Dana
Tested and validated to rigorous OE specifications
Latest production upgrades ensure genuine Spicer parts are as good or better than the OE parts they replace

from

$77.99

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$47.99

7.5″ C/clip, AG positraction

Product Features:

C-clip
Fits Ford 7.5″ with Auburn Gear positraction

from

$6.99

Axle seal for 5707 OR 1563 bearing.Yukon Mighty seal.

Product Features:

Rear axle seal
2.250″ O.D.

from

$5.19

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

Most Popular 1989 Ford Aerostar Differentials

Customize your Ford with 182 Differentials products like Differential Oil, Rear Housing Cover Gaskets, and Rear Differential Cover Gaskets, all priced under $1,566.99.

show more show less

from

$35.99

Valvoline MaxLife Multi-Vehicle ATF is a full-synthetic formulation with advanced additives to prevent the major causes of transmission breakdown and help extend transmission life. Developed to help prevent leaks, maximize transmission performance, reduce transmission wear, and maintain smooth shifting longer than conventional fluids. It is suitable for use in a broad range of ATF applications including most Ford, GM, Toyota, Honda, Nissan, Hyundai, BMW, Mercedes, Volvo, VW & Audi. Recommended for use in the following applications: GM DEXRON-II, DEXRON-III, DEXRON-VI, Ford MERCON LV, Toyota/Lexus Type T, T-II, T-IV, WS, Honda/Acura, ATF-Z1, Nissan/Infiniti Matic-D, Matic-J, Matric-K, Matic-S, Hyundai/Kia SP-II, SP-III, SP-IV, SPH-IV, BMW 7045E, ETL 8072B, LA2634, LT71141, Allison C-4, Mercedes Benz NAG-1, Volvo 1161521, 1161540, 97340, 1273.41, and VW/Audi G-052-025-A2, G-052-162-A1. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.

Product Features:

Formulated with full-synthetic base oils and long life friction modifiers to help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks in high mileage transmissions
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$16.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

CONSISTENT PERFORMANCE — Matched cup and cone components ensure consistent performance
PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION — Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN — Engineered to meet OE specifications
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$11.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$10.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$7.99

High-quality Differential Component Shim

Product Features:

SHIM KIT FITS-8.25-F7.5-AMC20-GM0

from

$350.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.Powertrax® = Extreme Traction Systems!

from

$23.49

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Design type: spring loaded; multi-lip
Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$6.79

Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$7.49

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Validated for fit, form and function
Unsurpassed quality you can trust

from

$6.99

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

from

$505.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.Powertrax® = Extreme Traction Systems!

from

$109.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

DANA-30 FORD MASTER BRG KIT

from

$37.99

DIFF COVER KIT

from

$123.99

Product Features:

CLUTCH PACK KIT 8.8″ FORD 1 KIT PER UNIT

from

$57.99

3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.

Product Features:

Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive

from

$44.99

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

Includes three quarts of conventional oil

from

$6.99

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features:

35 spline
8 x 3.96″ bolt pattern
Cut to length design fits 40″-43.5″ applications
Fits Dana Spicer 60, 70 and 80

from

$6.49

Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles
Required replacement – when servicing the differential
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$11.99

Replacement ring gear bolt for Model 35, Dana 25, 27, 30 & 44. 3/8″ x 24.

Product Features:

Ring gear bolt for Dana Spicer 25, 27, 30, 44 and AMC Model 35
3/8″ x 24 thread

from

$12.99

Product Features:

Cover gasket
Fits Dana Spicer 30

from

$9.99

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
1/2″ head

from

$9.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$4.99

Product Features:

Oil baffle for Dana Spicer 30, Dana Spicer 44 IFS, Dana Spicer 50, AMC Model 35 IFS

from

$10.99

Dana 25, Dana 27, & Dana 30 side gear Thrust washer.

Product Features:

Side gear thrust washer for Dana Spicer 25, 27, 30 and AMC Model 35
1.560″ I.D.
Fits standard open differentials only

Top Picks for 1989 Ford Aerostar Transfer Cases

Upgrade Ford Aerostars with top-quality Transfer Cases parts, including 9 OEM and aftermarket selections for your 1989 model.

show more show less

from

$15.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION — Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN — Engineered to meet OE specifications
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$11.49

Design type: spring loaded; multi-lip
Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$15.49

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$17.49

Product Features:

Brand may vary by location

from

$19.49

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$18.99

Transfer case gasket warped and cracked? This replacement gasket restores a tight seal to prevent fluid leaks on certain vehicle years, makes and models.

Product Features:

Product Features:

Direct replacement – this transfer case gasket matches the fit and performance of the original gasket on specific vehicle applications
Effective fix – restores a tight seal in the transfer case after original gasket fails
Durable construction – built for reliable longevity, free of defects in materials and workmanship
Trustworthy quality – backed by team of designers and engineers in the United States

from

$13.29

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$11.29

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$10.49

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

In-Demand Universal Joints for 1989 Ford Aerostars

Select from 23 premium Universal Joints parts for your 1989 Ford Aerostar, with prices ranging from $6.99 to $289.99.

show more show less

from

$31.99

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$35.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE – Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN – Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR – Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE – Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$25.99

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

For U-Joints 355, 372 & 534G
Contains two 1.81″ bolt center clamps and four 5/16-24 x 1-5/16″ cap screws

from

$33.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$41.49

Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASEABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$15.99

Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$6.99

This universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles
Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$27.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$18.99

1310 & 1330 U/joint strap, Dana 30, Dana 44, Model 35, & 9.25″ w/bolts.

Product Features:

u-joint strap kit
Fits Dana Spicer 30 and 44, AMC Model 35 and Chrysler 9.25″
1310 and 1330 u-joint size
Includes two straps and four bolts

from

$44.99

Yukon 1310 U/Joint with zerk fitting on cross. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring.

from

$59.99

Yukon 1310 to 1330 adapter U/Joint. The 1310 side has a 3.219″ span and 1.062″ caps. The 1330 side has a 3.625″ span and 1.062″ caps. Both sides are outside snap ring.

from

$34.99

1310 U-bolts, 5/16″ x 1-3/8″ Dana 30, Dana 44, 8.2″, 12P, 12T, VET, Model 20.

Product Features:

u-joint u-bolt kit
Fits AMC Model 20, Dana Spicer 30 and 44, GM 8.2″, 12 bolt passenger car and truck and 1963-1979 Corvette
1310 u-joint size
Includes two u-bolts and four nuts

from

$31.49

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$78.99

Yukon 1350 to 1410 conversion u/joint.

from

$27.99

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASEABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$109.99

Yukon 1310 to Mechanics 3R adapter U/Joint.

from

$53.99

1330 Yukon Lifetime U/Joint. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring.

from

$57.99

1310 Yukon Lifetime U/joint. 1.718″ snap ring span, 1.062″ cap diameter. Inside snap ring.

from

$289.99

Yukon replacement yoke for Dana 30, 44, and 50 with 26 spline and a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 30 and 44
26 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
Strap style

from

$111.99

Yukon 1350 to Mechanics 3R adaptor U/joint.

from

$44.99

from

$31.99

from

$15.99

1330 U/joint U-bolts, 5/16″ X 1-9/16″, (7260 & 7290 BILLET).

Product Features:

u-joint u-bolt kit
Fits AMC Model 20, Dana Spicer 30 and 44, GM 8.2″, 12 bolt passenger car and truck and 1963-1979 Corvette
1330 u-joint size
Includes two u-bolts and four nuts

Most Sold 1989 Ford Aerostar CV Axles and Joints

Explore our best-selling Ford parts for the 1989 Aerostar among 4 OEM and aftermarket options starting from $27.99.

show more show less

from

$31.99

This CV joint boot kit contains the parts required to repair the CV joint on specified vehicles without removing the joint itself. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this CV joint boot kit contains the parts required to repair the CV joint on specified vehicles without removing the joint itself
Ideal solution – this kit is a reliable replacement for original components that have failed due to wear
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$36.49

Direct replacement – this CV joint boot kit contains the parts required to repair the CV joint on specified vehicles without removing the joint itself
Ideal solution – this kit is a reliable replacement for original components that have failed due to wear
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$27.99

Our CV Joint Boots provide various methods of eliminating the removal of the CV joint during installation. Uni-Fit boots can be stretched over the CV Joint and Quick Boots come in halves.

Product Features:

Direct replacement – this CV joint boot kit contains the parts required to repair the CV joint on specified vehicles without removing the joint itself
Ideal solution – this kit is a reliable replacement for original components that have failed due to wear
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$44.99

Direct replacement – this CV joint boot kit contains the parts required to repair the CV joint on specified vehicles without removing the joint itself
Ideal solution – this kit is a reliable replacement for original components that have failed due to wear
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Top-Rated Drivetrains Brands For Your 1989 Ford Aerostar

Shop for the best-rated brands offering Drivetrains and other products for your 1989 Ford Aerostars. Below you’ll find some of our best rated Drivetrains from National, Dorman, and Driveworks, and more. Drivetrains from these brands that fit a 1989 Aerostar start at just $3.49 and are rated as high as 4.3 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular National 1989 Ford Aerostar Drivetrains

When it comes to maintaining or upgrading your 1989 Ford Aerostar, using quality Drivetrains is essential to ensure durability and a perfect fit. National ticks all of those boxes. We offer a wide selection of National Drivetrains, specifically designed for the 1989 Ford Aerostar. With over 3 National brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $11.99, with an average price of just $14.99. Plus, with over 36 customer reviews and an average rating of 4.3 stars, you can trust that our National Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from $16.99

(25)

Multi-Purpose Bearing

“Smooth”

from $15.99

(9)

Bearing

“as advertised”

from $11.99

(2)

Bearing Race

“Reasonable price and woks well. front diff 2006 Escalade esv”

Popular Dorman 1989 Ford Aerostar Drivetrains

Dorman auto parts is one of the highest quality Drivetrain brands in the market. Any 1989 Ford Aerostar owner should feel confident when installing genuine Dorman parts in their vehicle. To ensure the best fit and performance for your 1989 Aerostar, Advance Auto Parts carries a full inventory of 3 Dorman Drivetrains. Plus you will be keeping your Ford in peak condition while saving money because prices on these Dorman Drivetrains range from $3.49 to $22.49, plus, with more than 7 customer reviews and an impressive 4.2 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from $5.49

(3)

Spindle Nut 3/4 In.-16 and M20 In.-1.0 Hex Size 1-1/16 In. and 27mm

“Fit just like the original.”

from $3.49

(3)

Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In.

“Same as oem”

from $22.49

(1)

Driveshaft Flange Bolts

“This item appears to be correct and my review is more of a bashing of AA help desk who apparently does not answer questions as you are lead to believe”

FAQs for 1989 Ford Aerostar Drivetrains

Which Drivetrains are best-sellers for 1989 Ford Aerostars?

Out of 241 Drivetrains that fit 1989 Ford Aerostars, the following parts are the top sellers:

Greaseable Premium Universal Joint (10086900) – $35.99
Universal Joint (10265714) – $15.99
Universal Joint Strap Kit (10086946) – $25.99

What’s the price range for 1989 Ford Aerostar Drivetrains?

Drivetrain prices for the 1989 Ford Aerostar start at $1.29 and go up to $1,566.99 for the most premium parts.

What’s the average price of a Drivetrain for a 1989 Ford Aerostar?

The average price for Drivetrains for the 1989 Ford Aerostar is $131.95. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Ford Aerostar model years?

Yes, we currently carry Drivetrains for 10 model years of Ford Aerostars between 1986 and 1997. Drivetrains are bought most frequently for the following model years: 1997, 1996, 1995, 1994, 1993, 1992, 1991, 1990, and 1988.

What are the cheapest Drivetrains for my 1989 Ford Aerostar?

The cheapest 1989 Ford Aerostar Drivetrains we carry in stock are:

Differential Ring Gear Bolt (10282257) – $1.29
Ring Gear Bolt (20520509) – $1.99
Differential Crush Sleeve (10282338) – $2.99
Differential Cross Shaft (10282201) – $2.99
Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (21260547) – $3.49

What are the top-rated Drivetrains that fit the 1989 Ford Aerostar?

Out of 861 reviews by customers, our 1989 Ford Aerostar Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 1989 Ford Aerostar and their top-rated products:

Spindles
- Spindle Nut 3/4 In.-16 and M20 In.-1.0 Hex Size 1-1/16 In. and 27mm (21260519) – $5.49
- Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (21260547) – $3.49
Differentials
- Spindle Nut 3/4 In.-16 and M20 In.-1.0 Hex Size 1-1/16 In. and 27mm (21260519) – $5.49
- Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (21260547) – $3.49
Universal Joints
- Spindle Nut 3/4 In.-16 and M20 In.-1.0 Hex Size 1-1/16 In. and 27mm (21260519) – $5.49
- Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (21260547) – $3.49

What types of Drivetrains do you sell for my 1989 Ford Aerostar?

As of 3/1/26, these are some of the most in-demand types of Drivetrains for a 1989 Ford Aerostar:

Can I get help with 1989 Ford Aerostar Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Ford Drivetrains and more.

What is your return policy for Ford Aerostar Drivetrains?

Advance Auto Parts keeps returns simple. For new Ford Aerostar Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1989 Ford Aerostar Drivetrains

Yukon Gear – O-Ring For Dana 30 & Model 35 Zip Locker Seal Housing (Part No.34005)

Yukon Gear – Ppinion Nut 7/8-20 Thread, 1 1/8 Socket (Part No.33146)

Motive Gear – Differential Pinion Solid Spacer Kit w/Shims (Part No.4104)

ATP – DIFF COVER KIT (Part No.111103)

Dorman – Help – Driveshaft Flange Bolts (Part No.80992)

USA Standard Gear – Spartan Locker for Dana 30 Differential with 27 Spline Axles, Includes Heavy-duty Cross Pin Shaft (Part No.17000)

Yukon Gear – Minor Install Kit For Model 35 IFS Differential For Ranger And Explorer (Part No.12068)

Schaeffler – Shaft Seal (Part No.SS2468)

Yukon Gear – Axle Seal For 5707 Or 1563 Bearing (Part No.30196)

Spicer – Universal Joint (Part No.5-1310X)

Dorman – Help – Differential Shaft Lock Bolt (Part No.81048)

Yukon Gear – Ford 7.5" C/Clip, Tracloc & Standard Open (Part No.33080)

Driveworks – Taper Bearing Cone (Part No.S-HM-88649)

Yukon Gear – Pinion Install Kit For Dana 30 Rear Differential (Part No.13017)

Yukon Gear – Bearing Race Driver (Part No.56022)

Yukon Gear – Replacement Oil Baffle For Model 35 IFS Front, Dana 25, 27, 30, 44 IFS & Disconnect And Dana 50 (Part No.33002)

Yukon Gear – Super Carrier Shim Kit For Ford 7.5", GM 7.5", 8.2" & 8.5" (Part No.55001)

Yukon Gear – Trac Loc Spring For Ford 7.5" (Part No.33514)

Motive Gear – Differential Carrier Shim Kit (Part No.1116)

Yukon Gear – Replacement Yoke For Dana 30, 44, And 50 With 26 Spline And A 1330 U/Joint Size (Part No.41020)

Spicer – Universal Joint, Greaseable 1310 Series OSR (Part No.5-153X)

Dorman – Help – Pinion Crush Sleeves (Part No.81056)

Dorman – Axle Shaft (Part No.630-230)

Yukon Gear – Dana 30 & Dana 44 Power Lok Bolt, Left Hand, & 8.75" Chrysler & 55P (Part No.33234)

Motive Gear – Performance Differential Ring and Pinion (Part No.F888373)

Yukon Gear – Standard Open & Tracloc Pinion Gear And Thrust Washer For 7.5" Ford (Part No.33296)

Schaeffler – Bearing – TRB (Tapered Roller Bearing) (Part No.KT36)

Yukon Gear – 8.5" & 8.2" GM Carrier Installation Kit (Part No.57008)

Dorman – Help – Driveshaft Flange Bolts (Part No.80992)

Spicer – Universal Joint (Part No.5-1310X)

Driveworks – Oil Seal (Part No.S-2146)

National – Wheel Bearing (Part No.5707)

Driveworks – Axle Repair Bearing (Part No.S-RP-5707)

National – Tapered Roller Bearing Cone (Part No.HM88649)

Yukon Gear – R1563Tav Rear Axle Bearing And Seal Kit (Part No.10004)

Yukon Gear – Ford 7.5", 8", 8.8", & 9" Axle Stud (Part No.33175)

Yukon Gear – Ford 7.5" C/Clip, Tracloc & Standard Open (Part No.33080)

Yukon Gear – Replacement Yoke For Dana 30, 44, 50, And 300 With 26 Spline And A 1310 U/Joint Size (Part No.41018)

Yukon Gear – Flange Yoke For Ford 7.5" Passenger And Truck (4.3" Od) (Part No.41045)

Yukon Gear – Replacement Redi-Sleeve Yoke Saver For Dana 25, Dana 27, Dana 30, Dana 44, Dana 50 (Part No.30222)

Spicer – Differential End Yoke (Part No.2-4-6111X)

Schaeffler – Axle Shaft Repair Bearing (Part No.DR0148K)

Yukon Gear – 7.5" C/Clip, Ag Positraction (Part No.33079)

Yukon Gear – Axle Seal For 5707 Or 1563 Bearing (Part No.30196)

Schaeffler – Shaft Seal (Part No.SS2468)

Valvoline – MaxLife Multi-Vehicle Automatic Transmission Fluid, 1 Gallon (Part No.773775)

National – Multi-Purpose Bearing (Part No.A-6)

National – Bearing Race (Part No.LM501314)

Driveworks – Taper Bearing Cone (Part No.S-LM-501349)

Motive Gear – Differential Pinion Shim Kit (Part No.1100)

Powertrax – Lock Right Locker (Part No.2210-LR)

National – Differential Pinion Seal (Part No.5778)

Dorman – Help – Differential Shaft Lock Bolt (Part No.81048)

Felpro – Axle Housing Cover Gasket Oval Shaped 10 Bolt Hole Gasket (Part No.RDS 55393)

Motive Gear – Differential Pinion Nut (Part No.379570S)

Powertrax – No-Slip Traction System (Part No.9204302700)

Motive Gear – Differential Master Bearing Kit – Timken (Part No.R30FRMKT)

ATP – DIFF COVER KIT (Part No.111103)

Motive Gear – Differential Clutch Pack (Part No.F8.8CPK)

Yukon Gear – 3 Qt – 80W90 Conventional Gear Oil With Posi Additive (Part No.15003)

Yukon Gear – 3 Qt – Penzoil 80W90 Conventional Gear Oil (Part No.15002)

Yukon Gear – Cover Bolt For Ford 7.5", 8.8" & 9.75" (Part No.33554)

Dorman – Help – Pinion Crush Sleeves (Part No.81056)

Yukon Gear – Replacement Ring Gear Bolt For Model 35, Dana 25, 27, 30 & 44 – 3/8" X 24 (Part No.33038)

Yukon Gear – Replacement Cover Gasket For Dana 30 (Part No.23003)

Yukon Gear – Dana 25, 27, 30, 44, Model 20 And Model 35, GM 7.5", 8.2", 8.5", 12P, 12T, C9.25 Rear Cover Bolt (Part No.33286)

National – Bearing Race (Part No.M86610)

Yukon Gear – Replacement Oil Baffle For Model 35 IFS Front, Dana 25, 27, 30, 44 IFS & Disconnect And Dana 50 (Part No.33002)

Yukon Gear – Dana 30 Side Gear Thrust Washer (Part No.33284)

National – Bearing (Part No.M88048)

National – Multi-Purpose Seal (Part No.1990)

National – Bearing Race (Part No.HM88610)

Driveworks – Tapered Roller Bearing (Part No.S-M-802048)

Driveworks – Taper Bearing Cone (Part No.S-HM-88649)

Dorman – Transfer Case Gasket (Part No.926-476)

Schaeffler – Shaft Seal (Part No.SS2480)

Schaeffler – Cup (Part No.M88010)

Schaeffler – Bearing Cone (Part No.KLM11949)

Spicer – Universal Joint, Greaseable 1310 Series OSR (Part No.5-153X)