from

$337.99

Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$17.79

Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:

Precision Machined
Case Hardened
Give Accurate Alignment
2 Per Set

from

$57.99

Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Silicone beading on both sides of each gasket
Complete with manifold end seals and distributor gasket
For OE replacement, high performance street, drag race and oval track use
Creates Tight Leak proof Seal

from

$165.99

Magnum Pushrods from COMP Cams offer an affordable solution for your .080″ wall chromemoly pushrod needs. Designed to withstand the stresses of a high performance engine, Magnum Pushrods are head-treated for extended durability and have precision formed, reinforced ends. Magnum Pushrods are black-oxide finished with their part number and length laser etched onto the surface for easy identification.

Product Features:

3/8″ Diameter, 7.800″ Length
Magnum Pushrods for Small Block Chevy
One-piece .080″ wall chromemoly steel tubing
Heat-treated for extended durability and guide plate compatibility
Precision formed and reinforced pushrod end

from

$159.99

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

Complete Kit: Includes Retainers And Locks
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Includes Superior Quality Steel Retainers
Includes 7 deg. Heat-Treated Valve Stem Locks
Retainers and Locks Black Oxide Coated
Non-Rotator Style: Dyno Tested and Street Proven
Great Match to Edelbrock Camshaft Kit

from

$12.99

Spectre’s Chevrolet V8 water neck fits 1966 – 1995 Chevy V8 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes bolts.

Product Features:

Fits 1966 – 1995 Chevy V8 engines
Includes bolts
Chrome plated
Designed for OEM fit
Easy to install
O-ring/gasket not included

from

$255.99

Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:

Twisted Snout Water Pump Design For Updated Style
Street Performance
Heavy Duty Shaft w/5/8 in. Pilot
Six-Blade Stamped Steel
Anti-Cavitation Impeller
100 Percent Leak Tested

from

$35.49

Edge molded rubber water outlet gasket is reusable, great for engines that require regular disassembling for maintenance. Incorporates solid aluminum carrier for strength and rigidity. Can be used with OE replacement or aftermarket chrome water outlets. Requires no gasket sealer.

Product Features:

Edge Molded Rubber Water Outlet Gasket Is Reusable
Requires No Gasket Sealer
Solid Aluminum Carrier For Strength/rigidity
Reusable – Ideal for Engines That Are Frequently Taken Apart & Reassembled

from

$43.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$10.99

Spectre’s Intake Bolt and Washer Set is engineered to provide premium quality hardware for Chevrolet 265-400 and Chrysler 273-440 small block engines. Measuring 3/8 inch-16 by 1 inch, these grade 5 bolts feature a corrosion resistant zinc-plated finish and hex heads to ensure easy installation. This kit includes 12 bolts and washers.

Product Features:

Designed for Chevrolet 265-400 and Chrysler 273-440 small block engines
3/8 inch-16 by 1 inch bolts
Kit includes 12 bolts and washers
Manufactured from high quality steel
Bolts feature hex heads

from

$35.99

Mr. Gasket Performance Oil Pan Gaskets are manufactured from a high-density cork /rubber blend gasket material to provide excellent sealing and durability. Comes complete with molded rubber front/rear oil pan seals. For original equipment replacement and high performance street use.brbrFits Chevrolet 265,283,302,307,327,350,400 Gen I Small Block.

Product Features:

Manufactured from high-density cork /rubber blend gasket material
Provides excellent sealing and durability
Complete with molded rubber front/rear oil pan end seals where applicable
For OE replacement and high performance street use

from

$395.99

HYDRAULIC – Mutha’ Thumpr: High performance street/strip, needs 9:1 compression, 2500+ stall, intake, gears and headers, rough idle.

Product Features:

HYDRAULIC – Mutha’ Thumpr: High performance street/strip, needs 9:1 compression, 2500+ stall, intake, gears and headers, rough idle.
287/304 Advertised Duration, 235/249 Duration @ .050″, .510″/.495″ Lift, 107 Lobe Separation
Valve spring upgrade required

from

$75.99

These grade 8 alloy steel, longer length bolts are designed to compensate for thread length lost when using head bolt washers. This allows increased torque and clamping. Set of 16 does one cylinder head.

Product Features:

Cylinder Head Bolts
Longer-Than-Stock
High Quality Grade 8 Alloy
Increase Torque Settings
Higher Clamp Loads On Gasket

from

$32.49

Secure the harmonic balancer or dampener on your Chevy. Works on original equipment, high performance street, drag or circle track applications. Features a heat treated black oxide coated Grade 8 alloy steel bolt for strength with a tall hex head to prevent wrench from slipping. An extra thick parallel ground washer provides accurate, uniform torque, and a lock washer is also included.

Product Features:

Heat treated black oxide coated Grade 8 alloy steel
Tall hex head bolt to prevent wrench from slipping
Extra thick parallel ground washer provides accurate, uniform torque
Washers Provides More Accurate And Uniform Torque
Grade 8 Alloy Steel

from

$144.99

Includes: 2 short chrome valve covers 2 valve cover gaskets 1 chrome push-on breather 1 chrome dipstick & tube 1 chrome timing chain cover 1 chrome timing tab 1 rubber grommet for valve cover PCV hole 1 breather grommet.

Product Features:

Chrome Plated Steel
Comes W/valve Cover Gaskets

from

$19.99

It’s easy to overlook the small details. For engine builders focused on the larger components like camshafts, cylinder heads and pistons, small parts are often forgotten until the final stages of engine assembly. COMP Cams Engine Finishing Kits include those often missing parts like woodruff keys, cylinder head alignment dowels, cam bolts, and timing cover and oil pump dowel pins that are so crucial to properly assembling your engine.

Product Features:

Includes parts such as woodruff keys, cylinder head alignment dowels, cam bolts, timing cover and oil pump dowel pins
Available for various engine applications

from

$15.99

Roller cam lobes are ground flat rather than tapered like a flat tappet cam; it is necessary to provide some means of holding the cam back to the rear of the engine. The thrust button rides between the front of the timing gear and the back of the front cover and can be shimmed for proper end play of the cam. COMP Cams has both the solid nylon button and the roller thrust bearing available for the ultimate in performance.

Product Features:

.810″ Length
Ride between the front of the timing gear and the back of the timing cover
Can be shimmed to achieve proper endplay
Solid nylon and roller thrust bearing styles available

from

$32.49

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 195 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$433.99

These COMP Cams Ultra-Gold Aluminum Roller Rocker Arms with a 3/8″ stud diameter and 1.6 ratio are designed for Chevrolet V8 265-400 applications. The new modern design features of these Ultra-Gold Rockers are proven to withstand extremely aggressive spring pressure and valve lift. Designed specifically for high performance street and race engines, the Ultra-Gold Aluminum Rocker Arms are precision CNC-machined to strict tolerances. Developed to meet the demands of professional engine builders, these rockers include features never before possible in an aluminum rocker arm.

Product Features:

CNC-machined, lightweight design removes weight and yields unrivaled quality and ratio accuracy
Designed for high performance street and race engines
Precision-sorted trunion bearings withstand elevated valve spring pressure and valve lift
Additional clearance, up to 1.650″ O.D. valve spring

from

$44.99

Product Features:

Replacement Gasket Set For PN[4242]

from

$64.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$937.99

BIG BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.

Product Features:

Cam and lifter kit for Big Block Chevy engines
CL-Kit includes cam, lifters, assembly lube, instructions and decals
HYDRAULIC – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.
295/312 Advertised Duration, 243/257 Duration @ .050″, .522″/.507″ Lift, 107 Lobe Separation
Valve spring upgrade required

from

$1152.99

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Product Features:

Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
Best with aftermarket converters and more rear gear.
Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.