2001 Ford E-350 Super Duty Fluids and Chemicals

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• MAXLIFE TECHNOLOGY PREVENTS engine breakdown with 40% better wear protection than the industry standard
• REFRESH AGING SEALS AND PREVENT LEAKS with seal conditioners
• REDUCE SLUDGE, DEPOSITS, CORROSION, AND RUST with added detergents – keep motors clean inside
• ENHANCED FRICTION PERFORMANCE HELPS MAXIMIZE POWER with advanced friction-fighting agents
• MEETS OR EXCEEDS ALL REQUIREMENTS of ILSAC GF-6A, API SP, API SN with SN PLUS, API SN
• MaxLife Technology: Valvoline High Mileage with MaxLife Technology is specially formulated to maximize engine life in vehicles with over 75,000 miles, providing superior protection against wear, friction, heat, and deposits.
• Synthetic Blend Composition: This motor oil features a unique combination of synthetic and premium conventional oils, ensuring optimal performance and protection for high-mileage engines.

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• Seal conditioners rejuvenate aging engine seals to help stop and prevent oil leaks
• Extra wear protection helps prevent future engine wear
• Extra detergents help keep older engines cleaner by bonding with and removing sludge and deposits
• Anti-oxidants help prevent oil breakdown preventing engine-clogging sludge and deposit formation
• Advanced Synthetic Blend Formulation: Valvoline High Mileage with MaxLife Technology features an advanced synthetic blend that provides superior protection for engines with over 75,000 miles.
• API SN with SN PLUS Specification: Meets the API SN with SN PLUS specification, offering protection for gasoline direct-injected engines from low-speed pre-ignition, making it suitable for both high mileage and newer cars.

High Performance Motor Oil API LICENSED MOTOR OIL Royal Purple High Performance Motor Oil combines premium base oils with proprietary additive technologies to create a high performance synthetic engine oil that optimizes performance and protection. Royal Purple High Performance Motor Oils carry the current API and ILSAC engine oil licenses, as well as the GM dexos1 gasoline engine oil approval. ILSAC GF-6 AND GM DEXOS1 Modern gasoline direct injection (GDI) engines have achieved levels of power and fuel economy never before possible in passenger car engines. As a result, smaller engines operate at much higher loads across all engine speeds. This has caused increased wear in critical areas of the engine, and created a destructive phenomenon called low-speed pre-ignition (LSPI). The unique, state-of-the-art additive technology in Royal Purple High Performance engine oils is designed specifically to address these issues, and help engines maintain performance and reliability.

Product Features:

• Better Wear Protection
• Increased Protection against Low Speed Pre-Ignition
• Increased Fuel Efficiency
• Better Protection for Vehicle Exhaust Emissions Equipment
• Improved Compatibility with Fuels Containing Ethanol
• Superior Corrosion Protection
• Made in USA

Prestone® DOT 3 Motor Vehicle Brake Fluid delivers enhanced performance vs. DOT standards, benefitting all vehicles calling for DOT 3. This synthetic fluid starts with a higher dry boiling point than the DOT minimum standard to protect against overheating, brake fade and performance decline due to water absorption. This extended life (50,000 mile) fluid is also formulated to prevent corrosion of all metals within the braking system.  This formula is safe to use in all DOT 3 braking systems (ABS, disc or drum) and can mix with any DOT 3 fluid.  It is recommended to only use the DOT fluid specified for your car, as using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 50,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with High Grade Formula*
• Protects against performance decline due to water absorption. Prevents corrosion of all metals within the braking system.
• Synthetic, Extended Fluid Life Formula

Pentosin DOT 4 LV is a special brake fluid of highest DOT 4 performance levels and extremely low viscosity at cold temperatures. It offers safety against vapor lock; it has excellent resistance to absorbing and retaining water and provides superior corrosion resistance. Pentosin DOT 4 LV Brake Fluid is ideal for all modern vehicles with ESP and ABS. DOT 4 LV can be used in all vehicles that require DOT 4 fluid. High safety margin against vapor lock. Long-term resistance to absorbing and retaining water. Superior corrosion resistance. Low viscosity fluid provides excellent flow performance at low temperature.

Product Features:

• Safety against vapor lock
• Provides superior corrosion resistance
• Highest DOT 4 performance levels and extremely low viscosity at cold temperatures.

Prestone® MAX DOT 3 Motor Vehicle Brake Fluid is our highest grade formula, maximizing performance vs. DOT standard. Prestone MAX is our best brake fluid at protecting against overheating and brake fade. With 100,000 mile fluid life, our longest life fluid has 2X more miles between replacement than regular Prestone DOT 3. Prestone MAX has superior performance in severe braking conditions when compared to regular Prestone DOT 3, which means even more piece of mind about the braking system. This synthetic fluid starts with our highest dry boiling point giving our best protection against performance decline due to water absorption. Prestone MAX DOT 3 is safe to use in all DOT 3 braking systems, ABS, disc or drum, and can mix with any DOT 3 fluid. Mixing Prestone MAX with other fluids will lower the performance rating for miles and boil points, for best results replace completely with Prestone MAX DOT 3. It is recommended to only use the DOT fluid specified for your car. Using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 100,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with Our Highest Grade Formula. Prevents corrosion of all metals within the braking system.
• Superior Protection in Extreme Braking Conditions
• Synthetic, Long Life Formula – 2X Longer than regular Prestone DOT 3

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Today’s advanced engine technology requires advanced protection. Valvoline Advanced Full Synthetic, the motor oil designed to protect today’s sophisticated engines, contains premium anti-wear additives, superior antioxidants and extra detergents. It protects 40% better against wear, resists oil breakdown 10-times better, and defends 25% more against deposits than industry standards for maximum performance and engine longevity. And with an exceptional range of temperature protection your engine will ready for extreme weather. Valvoline invented motor oil 150 years ago, and we’ve been reinventing it ever since. Get Valvoline Advanced Full Synthetic and give your engine the advanced protection proven to maximize engine life.

Product Features:

• ADVANCED PROTECTION AGAINST the four main causes of engine breakdown: wear friction heat and deposits
• 40% BETTER WEAR PROTECTION vs. industry standard as tested in the Sequence IVB engine test
• 25% BETTER DEPOSIT PROTECTION with superior engine cleaning detergents as tested in the GMOD engine test
• EXCEPTIONAL HIGH/LOW TEMPERATURE PROTECTION defends your motor no matter the weather conditions
• MEETS OR EXCEEDS ALL REQUIREMENTS of ILSAC GF-6A, API SP, API SN with SN PLUS, API SN, GM dexos 1 Gen 3
• Enhanced Oil Stability: Resists oil breakdown 10-times better than industry standards, providing consistent performance and reliability.
• Premium Additives: Contains premium anti-wear additives, superior antioxidants, and extra detergents for maximum performance and engine longevity.

Quaker State Full Synthetic Motor Oil SAE 5W-30 contains the most powerful formulation in the Quaker State portfolio. This product offers superior resistance to thermal and viscosity breakdown compared to Quaker State Synthetic Blend Motor Oil. As the engine temperature increases, the heat activated shear stable viscosity modifiers work to maintain oil film thickness that is necessary to prevent engine parts from metal on metal contact which helps extend engine life. This motor oil maintains its viscosity from start to finish, which means it stays in the grade specified by the car manufacturer throughout the recommended oil drain interval. The product also contains special detergents and dispersant additives that are designed to neutralize the harmful acids generated by the combustion process. This helps prevent the formation of sludge and deposits from forming on crucial engine parts. These properties of Quaker State Ultimate Durability full synthetic motor oil make it reliable and suitable for use in high performance vehicles such as sport cars, SUVs, trucks and minivans. It is compatible with biofuels, ranging from E10 to E85 and suitable for hybrid vehicles.

Product Features:

• Quaker State Ultimate Durability is our most powerful formulation, providing extreme engine performance and protection against deposits, which allows your engine to operate at maximum horsepower
• No leading synthetic motor oil provides better protection from friction-related wear when compared to industry standard Sequence IVA engine test results
• Helps protect against the effects of low-speed pre-ignition (LSPI) in modern turbocharged engines.
• Provides excellent protection against the formation of sludge and other harmful deposits when compared to Quaker State Synthetic Blend Motor Oil
• Superior lubrication flow and pumpability at high and low temperatures when compared to Quaker State Synthetic Blend Motor Oil

Formulated to meet the specific requirements of Subaru vehicles equipped with conventional (non-CVT) transmissions up to model year 2005. Recommended for service-fill in all Subaru automatic transmissions where SUBARU ATF HP is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. IDEMITSU is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. IDEMITSU application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.

Product Features:

• Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
• Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
• Provides superior cleanliness, maintaining the transmission free of sludge and varnish deposits
• Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
• Advanced anti-wear technology provides maximum protection to gears and bearings

Prestone® Power Steering Fluid + Stop Leak (PSF+SL) delivers increased system life and prevents & stops system leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. The stop leak additives also prevent leaks by rejuvenating seals before they leak. Also designed with Anti-wear System Protection, Prestone PSF+SL protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 50,000 Mile Fluid Life
• Includes Stop Leak Additives to prevent and stop power steering system leaks.
• Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber & gasket components.
• Conventional Formula – For use in all manufacturers

Prestone® MAX American Vehicles Power Steering Fluid (PSF) + Stop Leak maximizes and increases system life + the power to stop leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. This formula is also great at preventing leaks by rejuvenating seals before they leak. This synthetic fluid is designed with 2X Anti-wear System Protection, which means more protection against pump failure, squeals and clogs. 100,000 mile fluid life, 2X more than conventional fluid, extends the time between replacement. This fluid is formulated for American vehicle manufacturers: Ford, Lincoln, Mercury, Dodge, Ram, Jeep, Chrysler, GMC, Chevrolet, Buick, Cadillac, Pontiac, Oldsmobile and others. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 100,000 Mile Fluid Life. Synthetic Formula for longer life and more protection
• MAX + Stop Leak. Stop Leak Additives to prevent and stop power steering system leaks.
• For use in American vehicle manufacturers: Ford, Lincoln, Mercury, Dodge, Ram, Jeep, Chrysler, GMC, Chevrolet, Buick, Cadillac, Pontiac, Oldsmobile and other
• 2X Anti-Wear Protection for enhanced System Life vs. conventional fluid. More protection against pump failure, squeals and clogs

Prestone® Power Steering Fluid (PSF) delivers increased system life. Designed with Anti-wear System Protection, Prestone PSF protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 50,000 Mile Fluid Life
• Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber & gasket components.
• For use in all manufacturers
• Conventional Formula – For use in all manufacturers

Mobil 1 Synthetic ATF is a multi-vehicle, fully synthetic automatic transmission fluid that helps to improve overall transmission durability and cleanliness. Has exceptional thermal and oxidation stability and long-term frictional properties that help to improve and extend transmission efficiency, smooth shifting performance, and fuel economy. Mobil 1 ATF provides excellent low-temperature fluidity to promote reliable lubrication at temperatures down to -51C, and exceptional shear stability to help supports viscosity retention under the most severe heavy-duty, high-temperature operating conditions. Compatibile with mineral ATF fluids and all common seal materials to help provide excelent leakage control and reduce concern in top-off emergencies. Meets or exceeds the requirements of JASO 1-A and Ford MERCON V.

Product Features:

• Multi-vehicle, fully synthetic automatic transmission fluid that helps to improve overall transmission durability and cleanliness
• Exceptional thermal and oxidation stability to improve and extend transmission efficiency, smooth shifting performance, and fuel economy
• Excellent high and low-temperature fluidity to help support viscosity retention under extreme, heavy-duty operating conditions
• Compatibile with mineral ATF fluids and all common seal materials to help provide excelent leakage control
• Meets or exceeds the requirements of JASO 1-A and Ford MERCON V
• Manufacturer Part Number: 112980

Valvoline DEXRON-VI/MERCON LV ATF is a full-synthetic transmission fluid formulated with advanced additive technology to meet and exceed the requirements of the General Motors DEXRON-VI specification. It is officially licensed and approved by GM and is fully back-serviceable and can be used wherever DEXRON-II and/or DEXRON-III are recommended. Recommended for use in the following applications: DEXRON-VI, DEXRON-III, DEXRON-II, MERCON LV and Allison C-4.

Product Features:

• Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Help keep positraction chatter down with posi additive from Yukon Gear & Axle.

Product Features:

• positraction additive
• For use in any clutch-style limited slip

Prestone® LowTox® Antifreeze/Coolant provides performance, durability, and protection against corrosion of ALL cooling system metals. The propylene glycol formula provides an added margin of safety for pets and wildlife. When used as directed, LoxTox is a propylene glycol low silicate formula, which provides full protection for a minimum of one year; can be used to top-off cooling systems in vehicles using conventional antifreeze/coolant; will not harm rubber parts; and meets ASTM D3306 and D4985 standards.

Product Features:

• Defeat engine failure while keeping your pets’ safety in mind
• Resists rust and corrosion on all cooling system metals
• Propylene glycol provides an added margin of safety for pets and wildlife in the event of accidental ingestion

PEAK ORIGINAL EQUIPMENT TECHNOLOGY ANTIFREEZE + COOLANT for NORTH AMERICAN VEHICLES is a line of premium coolants specifically designed to match the technology and color requirements of North American vehicles. Each coolant is formulated with the same corrosion inhibitor technology that protected your vehicle straight from the factory. Color cues on the packaging and a list of covered vehicles on the front label make it easy to identify the right match for your specific vehicle. PEAK ORIGINAL EQUIPMENT TECHNOLOGY ANTIFREEZE + COOLANT for NORTH AMERICAN VEHICLES – ORANGE is an extended life antifreeze/coolant based on proprietary state-of-the-art organic acid technology (OAT). The ethylene glycol-based formula represents a carefully balanced mixture of organic acid corrosion inhibitors for complete protection of modern high-performance North American vehicle engines. It can be mixed with any DEX-COOL approved formulations in newer GM, Opel, Daewoo and Saab vehicles, as well as with antifreeze/coolant in Ford and Chrysler vehicles requiring an orange type product. This product’s orange color distinguishes its unique chemistry and ensures easy selection for North American vehicles requiring this type and color of coolant. PEAK ORIGINAL EQUIPMENT TECHNOLOGY ANTIFREEZE + COOLANT for NORTH AMERICAN VEHICLES – ORANGE is free of silicate, borate, phosphate, nitrite, and amines, and is fully compatible with other extended life coolants. It meets the performance requirements of ASTM D3306 and D4985. When installed as part of a complete flush and coolant fill, PEAK guarantees this coolant will provide service life protection of up to 150,000 miles or 5 years.

Product Features:

• Matches technology and color requirements of North American OEMs specifying a Green Conventional coolant
• Protects all cooling system metals, including aluminum, against damaging rust and corrosion
• Compatible with other conventional green antifreeze + coolant formulations
• Easy-to-pour bottle with color-coding and vehicle applications listed on the front to simplify selecting the right antifreeze + coolant
• Available as both concentrate and 50/50 prediluted products to do the job right
• Testing Requirements: For proper freeze and boil over protection, use a traditional refractometer or hydrometer to measure the percentage of ethylene glycol by volume.

ZEREX G05® is the automaker approved original chemistry used in newer Ford®, Chrysler® and Mercedes-Benz® automotive and diesel engines. Its Hybrid Organic Acid Technology (HOAT) chemistry combines the best of conventional and organic acid-based chemistry to provide the ultimate protection against rust and corrosion. ZEREX G05 antifreeze/coolant uses the highest quality virgin ethylene glycol for freeze and boil over protection and a hybrid organic acid corrosion inhibitor package to protect your engines from liner pitting and corrosion.

Product Features:

• Automaker approved technology. Provides protection for 5 years / 150,000 miles in light duty applications and 3 years / 300,000 miles in heavy duty applications
• Formulated for long life performance
• Low-silicate, low-pH and phosphate-free formula
• Helps protect all cooling system metals, including aluminum

Prestone American Vehicles (Orange) antifreeze+coolant is specially designed to work with these specific vehicles: Ford 2002 and newer; Chrysler 2000 and newer; GM 1995 and newer. Prestone’s Antifreeze+Coolants are designed to the highest standards using state of the art technology. These fluids are designed to not only manage the engine temp and protect from freezing up, but they also protect the engine from rust, corrosion, buildup, pitting and engine damage. All of those can cause engine part failure and expensive repairs. Avoid costly repairs and vehicles in the shop with Prestone Asian vehicles antifreeze+coolant. This fluid is designed to last 10yrs / 300,000 miles and also to protect the internal parts of the engine for 10yrs / 300,000, offically patented by Prestone.

Product Features:

• Specially formulated to work with vehicles using multiple colors of fluid; OAT, HOAT, G05. Ford 2002 and newer; Chrysler 2000 and newer; GM (Chevrolet, Buick, GMC, Cadillac, Oldmobile, Pontiac, Saturn) 1995 and newer.
• Superior protection guarantee – 10 Yr., 300,000 mile Extended life formula
• Includes patented Prestone CorGuard technology, the best advancement in cooling system parts protection that protects against rust and corrosion of all cooling system metals, including aluminum. Protection for 300,000 miles.
• Ready to Use formula. Perfect for small volume top-off or complete drain and refill of the cooling system.

Prestone DEX-COOL (Ready to use) antifreeze+coolant is specially designed to work with these specific vehicles: All GM® vehicles 1995 & newer (GM approved), most Ford® vehicles 2011 – 2018 and most Chysler® vehicles 2013 & newer. Prestone’s Antifreeze+Coolants are designed to the highest standards using state of the art technology. These fluids are designed to not only manage the engine temp and protect from freezing up, they also protect the engine from rust & corrosion. This fluid is designed to last 5yrs / 150,000 miles.

Product Features:

• Specially formulated to work with vehicles using orange colored fluid; HOAT. All GM 1995 & newer; Most Ford 2011-2018; Most Chrysler 2013 & newer
• 5 Yr., 150,000 mile Extended life formula
• Includes the Prestone protection package that protects against rust and corrosion of all cooling system metals, including aluminum.
• Ready to Use formula. Perfect for small volume top-off or complete drain and refill of the cooling system.

FRAM DEXRON®-VI FULL SYNTHETIC ATF represents the latest technology in full  synthetic automatic transmission fluids. This product is designed for the newest  generation of highly efficient transmissions now being installed in most vehicles, and is  DEXRON®-VI licensed by GM and meets JASO 1A performance requirements. It is a fuel  efficient choice for older models as well, such as those currently using DEXRON®-III. FRAM DEXRON®-VI FULL SYNTHETIC ATF is recommended for use in all GM  DEXRON® applications and in transmissions applications calling for Toyota WS, Nissan  Matic J and Matic S, Ford part numbers XT-10-QLV and XT-6-QSP, Honda Z-1 and DW 1, and Hyundai SP-VI. Check owner’s manual for specific recommendations.

Product Features:

• Outstanding resistance to oxidative and thermal breakdown.
• Exceptional low temperature fluidity.
• Excellent anti-wear properties.
• Excellent gear shift quality throughout service life.
• ALWAYS REFER TO YOUR VEHICLES OPERATING MANUAL TO SELECT THE CORRECT GRADE FLUID FOR YOUR TRANSMISSION
• TRANSMISSION FLUIDS ALSO APPLICABLE IN POWER STEERING UNITS; CHECK OWNERS’ MANUAL

Automatic transmission fluid is a technologically advanced, low viscosity formulation specially designed to deliver performance and maximum fuel efficiency for modern automatic transmissions.

Product Features:

• Full Synthetic, low viscosity formulation
• OEM approved and licensed by Ford (MERCON® LV) and GM (DEXRON® -VI)
• Low viscosity formula for maximum fuel efficiency in modern automatic transmissions
• Enhanced friction durability for smooth transmission performance
• Superior high temperature protection to effectively resist oxidation
• Unsurpassed protection against copper corrosion
• Industry Specifications and OEM Approvals: JASO-1A
• Licensed and approved for use in: All GM vehicles (DEXRON®-VI, All previous DEXRON®); All Ford vehicles which specify Mercon® LV

The only parts recommended by Ford Motor Company for Ford, Lincoln and Mercury vehicles. Motorcraft and Ford Parts are used throughout Ford vehicles in a variety of applications that help ensure the proper build quality, integrity and long-lasting performance of every Ford car or truck. Motorcraft and Ford Parts are manufactured from first-quality materials – chosen specifically for maximum performance and application suitability. As with all Motorcraft and Ford Parts, any innovations or improvements developed since the vehicle’s manufacture are included in these after market replacement parts, ensuring the most current technology and performance.For use in all transfer cases

For use in power steering systems built after 2012

FRAM Mercon® V ATF is for use in Ford vehicle transmissions and transaxles.  Especially formulated to exhibit better low-temperature flow and better shear-stability,  FRAM Mercon® V ATF meets Ford performance requirements of vehicles specifying  Mercon® V ATF. FRAM Mercon® V ATF is recommended for use in all transmissions,  hydraulic systems, and power steering units manufactured by American, European,  Korean, Japanese and other manufactures from around the world specifying Mercon® V  type transmission fluids.

Product Features:

• Improved foam and corrosion prevention
• Improved oxidation stability
• Promotes smooth shifting
• ALWAYS REFER TO YOUR VEHICLES OPERATING MANUAL TO SELECT THE CORRECT GRADE OIL FOR YOUR TRANSMISSION
• TRANSMISSION FLUIDS ALSO APPLICABLE IN POWER STEERING UNITS; CHECK OWNERS’ MANUAL

Valvoline MaxLife Multi-Vehicle Automatic Transmission Fluid (ATF) is a full-synthetic formulation with advanced additives to prevent the major causes of transmission breakdown and help extend transmission life.  Developed to help prevent leaks, maximize transmission performance, reduce transmission wear, and maintain smooth shifting longer than conventional fluids. It is suitable for use in a broad range of ATF applications including most Ford, GM, Toyota, Honda, Nissan, Hyundai, BMW, Mercedes, Volvo, VW & Audi.

Product Features:

• Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
• Long life friction modifiers help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
• High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks in high mileage transmissions
• Developed with anti-wear technology to help improve transmission durability
• Advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures
• Suitable for 95% of traditional ATFs including Dex/Merc, Mercon LV & Mercon V

Castrol Transmax ATF/CVT Universal is a technologically advanced full-synthetic formulation designed to deliver excellent performance in most of the traditional stepped automatic transmissions and Continuously Variable Transmissions currently in use. It is also suitable for use in hybrids.

Product Features:

• Coverage of over 300 specs/95% of vehicles in operation
• Broad scope of vehicle applications improves workshop efficiency and inventory management
• Enhanced friction durability for smooth transmission performance
• Superior high temperature protection to effectively resist oxidation