from

$349.99

A higher than stock stall speed as delivered by a B&M Converter will provide several advantages. The high stall converter allows the engine to launch the car at a higher RPM where more torque is available and increased strength.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$54.99

Spectre’s Ford V8 water neck fits Ford 429 – 460 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes sealing O-ring, and has a 3/8 inch NPT threaded hole for the Ford temp sensor.

Product Features:

Fits Ford 429 – 460 engines
Has a 3/8 inch NPT threaded hole for temperature sensor
Includes sealing O-ring
Chrome plated
Easy to install
Hardware not included

from

$38.49

Mr. Gasket Harmonic Balancer Bolt for Ford V8 except 351C. Fits 221,260,289,302,351W small block Windsor engines, 332,352,360,390,406,410,427,428 FEs, and 429,460 385 series big blocks. 5/8-18 x 2 inch long heat treated black oxide coated Grade 8 alloy steel with a thick parallel ground washer to provide accurate, uniform torque.

Product Features:

Heat treated black oxide coated Grade 8 alloy steel
Thick parallel ground washer provides more accurate, uniform torque
Hex Prevents Socket Slippage
Accurate And Uniform Torque
Black Plated Finish

from

$32.59

Product Features:

Prevents Air Inclusion
Direct Replacement
For OE Bleeders
One Person Bleeds Safely
Without The Mess
No Chance Of Air Bubbles

from

$438.99

Our advanced power system line has grown to include starters. Our new APS starter is designed to crank over the highest compression engines on a hot day in Death Valley. Not that too many race cars are sitting in Death Valley, but it’s good to know that you have the oomph to make it happen. The APS starter features all new components beginning with a three horsepower motor. This power is used to crank over the reduced 4.4:1 gear set to deliver great torque to the engine’s ring gear to get the engine turning. The armature is balanced during assembly and is guided by two ball bearings for smooth engagement and thousands of starts. The downsized housing clears most headers and oil pans, but just in case, we made the billet mount so it can be clocked in different positions to help in tight applications. The assembly is powder coated MSD red and will stay looking good, even though it’s underneath your car.

Product Features:

Mount Can Be Clocked To Assist In Mounting
Downsized design helps clearance issues w/oil pans and exhaust
Ball bearing supported armature and pinion gear
3 Hp Motor Provides Power For High Compression Engines
Gear reduction of 4.4:1 improves torque for great cranking

from

$217.99

Keith Dorton Series VoluMax race series fuel pump made from heavy duty construction for continuous high RPM operation. Redesigned high flow valves always ensure adequate fuel delivery. Fuel pressure regulator is required. Fuel body casting can be rotated

Product Features:

High Output Fuel Flow
Flows 170+ gph Free Flow
Shutoff Pressure Pre-Set At 8 PSI
Fuel Pressure Regulator Is Not Required
Heavy Duty Construction For Continuous High rpm Operation
Redesigned High Flow Valves Always Ensure Adequate Fuel Delivery
Fuel Body Casting Can Be Rotated For Plumbing Situations
Inlet And Outlet Tapped For 3/8 in. NPT

from

$724.99

The off-road truck avenger is designed specifically for off-road applications. The unique fuel metering block eliminates fuel spillover through the boosters at extreme angles allowing for 40 degree climbing, 30 degree side hill maneuvers and nose-down descents to avoid hesitations, stalling and flooding typically associated with carbs in an off road environment. The 470 CFM off-road truck avenger is the perfect carburetor for 4 cylinder, V-6, and inline 6 cylinder engines. Viton(R) is a registered trademark of DuPont Performance Elastomers.

Product Features:

Gold Dichromate Finish For Extreme Off Road Environments
Single Feed Fuel Inlet For Ease Of Installation
Optimized Off-Road Calibration That Works Out-Of-The-Box
Factory Preset Electric Choke For Easy Startups
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
One Piece Off-Road Vent Tube Eliminates Fuel Spillover
Metering Block For Flood Free Op. 40 deg. Climb/30 deg. Side Hill
Limited Lifetime Warranty Defects In Material/Workmanship

from

$48.09

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:

Indicates coolant temperature
Helps prevent coolant injuries
Fahrenheit and centigrade readings
Color-coded temperature ranges
Integrated coolant reclamation valve
Improves under-hood appearance
Chromed crown with a colored trim ring

from

$48.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PTFE offers the best in fluid and high-temperature compatibility and contact sealing surface can run on undersize shafts, seal minor imperfections and virtually eliminate shaft wear.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$183.99

This Mr. Gasket Oil Pan comes in chrome plated steel. Complete with drain plug, washer & bolts. Stock depth and capacity. Gasket & chrome-plated dipsticks with tubes sold separately.

Product Features:

Includes Mounting Bolts
Includes Drain Plug/Washer/Bolts

from

$64.99

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$35.99

Graphite impregnated facing and a steel expanded metal core. Superior tensile strength. Resists cracking and withstands intense heat. Resists deteriorating. Anti-stick properties and easy removal for disassembly.

Product Features:

Graphite-Impregnated Facing
Steel Expanded Metal Core
Superior Tensile Strength
Resists Cracking
Withstands Intense Heat
Resists Deteriorating
Anti-Stick Properties
Easy Removal For Disassembly

from

$59.99

Available in various sizes, heights, and finishes, Spectre offers a wide variety of high performance valve covers designed to easily replace your stock covers. Designed for 1965-1987 Ford Straight 6 cylinder 240-300 engines, this valve cover features chrome-plated steel construction and a smooth design. This stock profile cover is baffled to provide optimum function. With show quality construction and a sealing edge designed for an ideal fit, our valve covers are engineered to look great for applications ranging from custom builds to replacing stock equipment.

Product Features:

Designed for 1965-1987 Ford Straight 6 cylinder 240-300 engines
Baffled for breather system compatibility
Triple chrome-plated steel construction
Stock height
Features OEM style sealing edge

from

$45.99

Designed to allow additional adjustment of the clutch fork height to eliminate clutch release problems when installing a high performance clutch. Recommended for use with Lakewood safety bell housings. Available for most GM, Ford, and Mopar applications. Adjustable dowel pins correct for improper register bore alignment of bell housing.

Product Features:

Allows Additional Adjustment
Eliminates Clutch Release Problems

from

$60.99

MSD Ignition is a company built on Customer Satisfaction and Service. That is why all of MSD products go through regimented test procedures before they are ever packaged and shipped. MSD stands behind its products for one full year after purchase

Product Features:

Rotor phasing can be adjusted.
Ideal When Atomic TBI Is Controlling The Timing

from

$30.49

Product Features:

Service Part
Makes Connections Quick And Easy

from

$570.99

The street Pro-Billet distributors are the perfect choice for powerful engines that see plenty of street time. The street models share the same features as the small diameter models shown above, plus feature a vacuum advance. This canister provides improved economy and an accurate mechanical advance lets you dial-in an advance curve to match your driving needs. A magnetic pick-up produces accurate trigger signals that remain stable throughout the entire RPM range of your engine and is completely maintenance-free.

Product Features:

Billet housing 5/8 in. smaller dia. than stock Ford distributors
CARB E.O. Approved
Easy-to-adjust mech. advance w/supplied springs and stop bushings
Vacuum advance canister for improved economy (can be locked out)
CNC machined billet aluminum housing and billet aluminum base
Maintenance-free magnetic pickup and precision reluctor
Creates stable trigger signals throughout the rpm range
QPQ coated polished steel shaft; guided by sealed ball bearings

from

$382.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Stock Replacement
50-State Street Legal

from

$237.99

The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.

Product Features:

Cost effective aluminum construction provides superior strength to weight ratio
Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
Durable design increases valve lift while withstanding the rigors of moderate race use
Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.

from

$36.99

Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.

Product Features:

Allows Sway Bar System to Work At 100% Efficiency
Zerk Type Fittings
Allows for Periodic Greasing
Lasts Much Longer Than OEM Rubber Bushings
Handling Characteristics Improve Dramatically

from

$391.99

LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:

High Performance
Affordable
Durable 16 Gauge Material
Welds Easier
Lasts Longer
Heat Cured
High Heat Resistant

from

$190.99

Edelbrock part #9659 Pushrods are designed for small-block Ford 351W V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise f

Product Features:

7.7 in. Length
0.312 in. Diameter
4130 Chromoly Steel Material
Black Oxide Finish
Made In The USA

from

$15.99

Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provi

Product Features:

PerTronix D4061 Flame-Thrower HEI Distributor Rotor Red
Made from hi-performance 60 KV rated alkyd molding compound.

from

$550.99

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

Good blend of efficiency and performance.
Perfect choice for performance street rebuilds.
Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

from

$67.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Meets or exceeds all original equipment specifications
Validated for fit, form, and function
Application specific design to ensure a perfect fit and correct operation for Unsurpassed quality you can trust
Engineered and manufactured specifically for the repair environment
Every part for the repair procedure is Includes in the kit unless otherwise noted

from

$40.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro performance intake manifold gaskets have been tested with virtually all aftermarket cylinder head and intake manifold combinations.
Performance intake manifold gaskets designed without a metal core, to allow engine builders to trim the gasket for exact fit on modified ports.
5.4L Cobra R; Upper intake
Not intended for use in emission controlled vehicles.

from

$12.09

If you have custom steel or mag wheels that are not designed without a provision for a center cap, you’re probably looking at an ugly stock dust cap in the center of your front wheels. This chrome dust cap fixes that problem, and is a direct replacement for stock cap 1.790 inches in diameter. Two per set.

Product Features:

Chrome Plated Steel
Set of 2 Caps
Easy Installation
2 Per Set

from

$379.99

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.