Name: Engine Crankshaft Seal Kit
Brand: FEL-PRO Performance
SKU: 2948
Price: 49.99 USD

from

$49.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$284.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$32.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$349.99

A higher than stock stall speed as delivered by a B&M Converter will provide several advantages. The high stall converter allows the engine to launch the car at a higher RPM where more torque is available and increased strength.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$21.79

Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:

6 3¿8″ diameter
6 3┐8″ diameter
289-302-351 cu. in.
Increased Performance
Set Valve Lash At Proper Time

from

$975.99

Product Features:

Complete Single For Hydraulic Flat Tappet
60cc Combustion Chamber Volume
170cc Intake/60cc Exhaust Runner Volume
1.9 in. Intake/1.6 in. Exhaust Valve Diameter
0.625 in. Deck Thickness

from

$358.99

Edelbrock #88433 Water Pump Ford 1970-78 302 & 1970-87 351w v8 black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cool

Product Features:

Standard Impeller Rotation
0.625 in. Pilot Shaft
0.750 in. Ball/Ball Bearing
5.70 in. Block To Hub Height
Black Finish

from

$87.19

Designed to keep the rocker arms positively locked for precise and critical valve train adjustments. Manufactured from quality grade steel, then heat-treated for extra strength and plated with a durable finish. Kits include 16 rocker arm nuts with socket head set screws and one hex key wrench.

Product Features:

(16) Rocker Arm Nuts w/ Locks 3/8″-24 Threads
Shank O.D. .540″
Includes Locks and Hex Wrench
High-Quality Grade Steel
Heat-Treated For Ex Strength
Plated With Durable Gold Tone Finish

from

$368.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$210.99

Product Features:

Case-Hardened Tubing
Surface Hardening
Welded Ends
0.3125 in. Diameter
Use with or without Hardened Steel Guideplates

from

$100.99

Product Features:

Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$81.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets

from

$51.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$354.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 deg. Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal if Correct Carburetor Used

from

$60.99

Product Features:

Valve Cover Gasket

from

$41.49

Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Manufactured from high-density cork/rubber blend gasket material
Provides excellent sealing and durability
For OE replacement, high performance street, drag race and oval track use

from

$107.99

Product Features:

Highest Quality Head Bolts
Cold-Formed/Heat Treated
Ensures Molecular Integrity
Reduced Diameter Bolt Heads
Hardened/Parallel-Ground Washers Included
Rated At 170000 psi
Manufactured By ARP

from

$54.99

Spectre’s Ford V8 water neck fits Ford 429 – 460 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes sealing O-ring, and has a 3/8 inch NPT threaded hole for the Ford temp sensor.

Product Features:

Fits Ford 429 – 460 engines
Has a 3/8 inch NPT threaded hole for temperature sensor
Includes sealing O-ring
Chrome plated
Easy to install
Hardware not included

from

$48.09

Precision die cast, these water necks or thermostat housings are first polished to a high luster, then chrome plated. Comes with gasket and Allen head mounting bolts. Fits 1979-1997 Ford 5.0/5.8L V8s.

Product Features:

Chrome Plated For Great Looks
Includes Gasket & Mounting Bolts

from

$111.99

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$59.99

Product Features:

Non-Rotator Type
1.400 in. Outer Diameter
1.000 in. Inner Diameter
1.000 in. Coil Blind
Set of 16

from

$19.99

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 5/16 inch-18 x 2 inch bolts & washers

Product Features:

Hex Head
Zinc Plated
Ideal For Minimal Space
12-Point Head And Flange
Zinc Plated For Protection

from

$43.99

Super Intake Manifold Bolts

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$39.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro performance intake manifold gaskets have been tested with virtually all aftermarket cylinder head and intake manifold combinations.
Performance intake manifold gaskets designed without a metal core, to allow engine builders to trim the gasket for exact fit on modified ports.
1970-82; w/2 Bbl. Cylinder heads
Printoseal elastomeric sealing beads to provide extra sealing strength around the intake port.
Not intended for use in emission controlled vehicles.

from

$35.99

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. Comes complete with front & rear manifold end seals. For original equipment replacement, high performance street, drag race and oval track.brbrFits 1977-1997 Ford Small Block 351 Windsor 2 or 4-barrel.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Die-cut for an excellent fit
Can be trimmed if necessary for modified port applications
Complete with manifold end seals
For OE replacement, high performance street, drag race and oval track use

from

$38.49

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. Comes complete with front & rear manifold end seals. For original equipment replacement, high performance street, drag race and oval track.brbrFits all Ford 351M/400 – 4V or 4-Barrel heads.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Die-cut for an excellent fit
Can be trimmed if necessary for modified port applications
Complete with manifold end seals
For OE replacement, high performance street, drag race and oval track use

from

$40.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro performance intake manifold gaskets have been tested with virtually all aftermarket cylinder head and intake manifold combinations.
Performance intake manifold gaskets designed without a metal core, to allow engine builders to trim the gasket for exact fit on modified ports.
5.4L Cobra R; Upper intake
Not intended for use in emission controlled vehicles.

1978 Ford E-250 Econoline Performance Engines

More 1978 Ford E-250 Econoline Performance Engines

Essential 1978 Ford E-250 Econoline Performance Engines

FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2948)

Competition Cams – Xtreme Energy 240/246 Hydraulic Flat Cam (Part No.35-250-4)

FEL-PRO Performance – Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set (Part No.1820)

B & M – Torque Converter, Tork Master 2000 (Part No.40427)

Mr. Gasket – Precision Timing Tape (Part No.1594)

Edelbrock – Performer Small-Block Ford 5.0L/ 5.8L Cylinder Head 1.90 Polished (Part No.603719)

Edelbrock – Water Pump for Small-Block Ford 351W in Black Finish (Part No.88433)

Mr. Gasket – Ultra Seal: Sure-Lock Rocker Arm Nuts (Part No.923G)

Edelbrock – Performer-Plus Camshaft Kit for Big-Block Ford 429/460 V8 (Part No.2167)

Edelbrock – Pushrod Set for Small Block Ford 289-302 (Part No.9632)

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9724)

Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7821)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1011-1)

Edelbrock – INTAKE MANIFOLD (Part No.3723)

Edelbrock – Valve Cover Gasket Set for Ford (Part No.7563)

Mr. Gasket – Valve Cover Gasket Set (Part No.278)

Edelbrock – 289-302 Ford Head Bolt Kit (Part No.8552)

Spectre – Water Neck; Ford 429-460 (Part No.4734)

Mr. Gasket – Water Neck (Part No.9713)

Edelbrock – Sure Seat Valve Springs for Ford 429/460 V8 1969-1987 (Part No.5767)

Edelbrock – Sure Seat Valve Springs for Ford 351M/400 V8 1971-1982 (Part No.5872)

Mr. Gasket – Intake Manifold Bolts (Part No.958G)

Mr. Gasket – Super Intake Manifold Bolts (Part No.6082)

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

FEL-PRO Performance – Lower Intake Manifold Gasket Set: 7 Piece Set (Part No.1240)

Mr. Gasket – Intake Gasket (Part No.223)

Mr. Gasket – Intake Gasket (Part No.222)

FEL-PRO Performance – Upper Intake Manifold (Plenum) Gasket Set: 2 Piece Set (Part No.1236)

Popular 1978 Ford E-250 Econoline Performance Engines Categories

1978 Ford E-250 Econoline Performance Engines

Performance Engines Brands To Make Your 1978 Ford E-250 Econoline Last

Popular FEL-PRO Performance Performance Engines

Top 1978 Ford E-250 Econoline Performance Engines from Mr. Gasket

FAQs for 1978 Ford E-250 Econoline Performance Engines

What are the most purchased Performance Engines for the 1978 Ford E-250 Econoline?

What are the top-rated 1978 Ford E-250 Econoline Performance Engines?

More Popular Parts for All Makes