Nissan 240SX Fluids and Chemicals

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• MAXLIFE TECHNOLOGY PREVENTS engine breakdown with 40% better wear protection than the industry standard
• REFRESH AGING SEALS AND PREVENT LEAKS with seal conditioners
• REDUCE SLUDGE, DEPOSITS, CORROSION, AND RUST with added detergents – keep motors clean inside
• ENHANCED FRICTION PERFORMANCE HELPS MAXIMIZE POWER with advanced friction-fighting agents
• MEETS OR EXCEEDS ALL REQUIREMENTS of ILSAC GF-6A, API SP, API SN with SN PLUS, API SN
• MaxLife Technology: Valvoline High Mileage with MaxLife Technology is specially formulated to maximize engine life in vehicles with over 75,000 miles, providing superior protection against wear, friction, heat, and deposits.
• Synthetic Blend Composition: This motor oil features a unique combination of synthetic and premium conventional oils, ensuring optimal performance and protection for high-mileage engines.

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• MAXLIFE TECHNOLOGY PREVENTS engine breakdown with 40% better wear protection than the industry standard
• REFRESH AGING SEALS AND PREVENT LEAKS with seal conditioners
• REDUCE SLUDGE, DEPOSITS, CORROSION, AND RUST with added detergents – keep motors clean inside
• ENHANCED FRICTION PERFORMANCE HELPS MAXIMIZE POWER with advanced friction-fighting agents
• MEETS OR EXCEEDS ALL REQUIREMENTS of ILSAC GF-6A, API SP, API SN with SN PLUS, API SN

FRAM DEX III/MERC ATF is formulated for older model Ford and General Motors  vehicles requiring MERCON®, DEXRON-I®, DEXRON-II® and DEXRON-III®. It is also  recommended for transmissions, power steering systems, and hydraulic systems  requiring a DEXRONIII® or Caterpillar TO-2 fluid. FRAM DEX III/MERC ATF may also  be used in compressors, pumps, and hydraulic systems. FRAM DEX III-H/M ATF is  recommended for use in all transmissions, hydraulic systems, and power steering units  manufactured by American, European, Korean, Japanese and other manufactures from  around the world specifying DEXRON®III H/Mercon® and earlier DEXRON®/Mercon® type transmission fluids.

Product Features:

• Good foam and corrosion prevention
• Safe for seals
• Promotes smooth shifting
• ALWAYS REFER TO YOUR VEHICLES OPERATING MANUAL TO SELECT THE CORRECT GRADE FLUID FOR YOUR TRANSMISSION
• TRANSMISSION FLUIDS ALSO APPLICABLE IN POWER STEERING UNITS; CHECK OWNERS’ MANUAL

FRAM DEXRON®-VI FULL SYNTHETIC ATF represents the latest technology in full  synthetic automatic transmission fluids. This product is designed for the newest  generation of highly efficient transmissions now being installed in most vehicles, and is  DEXRON®-VI licensed by GM and meets JASO 1A performance requirements. It is a fuel  efficient choice for older models as well, such as those currently using DEXRON®-III. FRAM DEXRON®-VI FULL SYNTHETIC ATF is recommended for use in all GM  DEXRON® applications and in transmissions applications calling for Toyota WS, Nissan  Matic J and Matic S, Ford part numbers XT-10-QLV and XT-6-QSP, Honda Z-1 and DW 1, and Hyundai SP-VI. Check owner’s manual for specific recommendations.

Product Features:

• Outstanding resistance to oxidative and thermal breakdown.
• Exceptional low temperature fluidity.
• Excellent anti-wear properties.
• Excellent gear shift quality throughout service life.
• ALWAYS REFER TO YOUR VEHICLES OPERATING MANUAL TO SELECT THE CORRECT GRADE FLUID FOR YOUR TRANSMISSION
• TRANSMISSION FLUIDS ALSO APPLICABLE IN POWER STEERING UNITS; CHECK OWNERS’ MANUAL

Prestone All Vehicles antifreeze+coolant (ready to use) is truly designed to work with all vehicles; all makes, models, years & fluid colors. It is designed to work with all new engines while also being backwards compatible improving protection in all older engines. The patented Cor-Guard technology (the best innovation in the category in decades) instantly protects parts from corrosion, buildup, pitting, scaling, rust and other damage. These fluids are specially designed to not only manage the engine temp and protect from freezing up (like competitors), but they also potect the engine from damage. Internal damage can cause engine part failure, leading to expensive repairs and serious inconveniences. Avoid costly repairs and vehicles in the shop with Prestone All Vehicles antifreeze+coolant. This fluid is designed to last 10yrs / 300,000 miles and also to protect the internal parts of the engine for 10yrs / 300,000, offically patented by Prestone.

Product Features:

• Formulated to work with All Vehicles. Works with all fluid colors; All OAT, POAT, HOAT & IAT.
• Longer Engine Life Guarantee – 10 Yr., 300,000 mile Extended life formula.
• Includes patented Prestone CorGuard technology, the best advancement in cooling system parts protection that protects against rust and corrosion of all cooling system metals, including aluminum. Protection for 300,000 miles.
• Ready to Use formula (prediluted to a 50% Eg & 50% distilled water mix). Perfect for small volume top-off or complete drain and refill of the cooling system

PEAK® Antifreeze + Coolant Concentrate is specially engineered to deliver guaranteed superior lifetime protection. Its advanced universal formula contains a proprietary blend of 10X the scale-fighting inhibitors coupled with robust organic additives to fight against the damaging effects of scale deposits and corrosion. PEAK Antifreeze + Coolant is free of 2-EHA, silicate, nitrite, borate, and amines, ensuring maximum cooling system performance for 10+ years/300,000+ miles. It is compatible for use with any color or type of antifreeze/coolant in the system.

Product Features:

• Specially formulated to deliver Superior Lifetime Protection against damaging scale and corrosion
• Contains 10X the scale-fighting inhibitors to ensure maximum cooling system performance
• Provides more than 2X the warranty coverage for 10+ years/300,000+ miles of service
• Universal formula is compatible with any color or type of antifreeze/coolant
• Meets the performance requirements of ASTM D3306 and D4985

FRAM Conventional Green Concentrate is an ethylene glycol-based product for use in car and light duty trucks that are already using a conventional coolant. The inhibitors prevent rust, corrosion, and provide freeze-up and boil-over protection. When used as directed, the Prime Green Concentrate Low Silicate formula provides full protection for a minimum of one year.

Product Features:

• Low Silicate Formula
• When used as directed, will provide protection for a minimum of 1 year
• Meets or exceeds ASTM requirements for cars, light duty trucks
• Concentrated formula. Must mix with high quality (distilled/deionized) water to the desired ratio. Can be used for top-off, complete drain and refill or flush and refill of the cooling system.

Mobil 1 Synthetic ATF is a multi-vehicle, fully synthetic automatic transmission fluid that helps to improve overall transmission durability and cleanliness. Has exceptional thermal and oxidation stability and long-term frictional properties that help to improve and extend transmission efficiency, smooth shifting performance, and fuel economy. Mobil 1 ATF provides excellent low-temperature fluidity to promote reliable lubrication at temperatures down to -51C, and exceptional shear stability to help supports viscosity retention under the most severe heavy-duty, high-temperature operating conditions. Compatibile with mineral ATF fluids and all common seal materials to help provide excelent leakage control and reduce concern in top-off emergencies. Meets or exceeds the requirements of JASO 1-A and Ford MERCON V.

Product Features:

• Multi-vehicle, fully synthetic automatic transmission fluid that helps to improve overall transmission durability and cleanliness
• Exceptional thermal and oxidation stability to improve and extend transmission efficiency, smooth shifting performance, and fuel economy
• Excellent high and low-temperature fluidity to help support viscosity retention under extreme, heavy-duty operating conditions
• Compatibile with mineral ATF fluids and all common seal materials to help provide excelent leakage control
• Meets or exceeds the requirements of JASO 1-A and Ford MERCON V
• Manufacturer Part Number: 112980

Valvoline DEXRON-VI/MERCON LV ATF is a full-synthetic transmission fluid formulated with advanced additive technology to meet and exceed the requirements of the General Motors DEXRON-VI specification. It is officially licensed and approved by GM and is fully back-serviceable and can be used wherever DEXRON-II and/or DEXRON-III are recommended. Recommended for use in the following applications: DEXRON-VI, DEXRON-III, DEXRON-II, MERCON LV and Allison C-4.

Product Features:

• Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Valvoline Import Multi-Vehicle Automatic Transmission Fluid is specifically formulated for use in most Toyota, Nissan, Honda and other imported vehicles. It is formulated with all synthetic base stocks and a proprietary additive system to ensure optimal transmission performance in a wide variety of vehicles. Valvoline Import Multi-Vehicle ATF can also be used in many domestic vehicles. It meets requirements of General Motors and Ford vehicles. Recommended for use in the following applications: Ford MERCON®, GM DEXRON®-II and DEXRON®-III, BMW LT 71141 and ETL-7045E, Nissan/Infiniti Nissan ATF, Matic-D, Matic-K and Matic-J, Mitsubishi Diamond SP-II and SP-III, Subaru ATF-HP, Hyundai/ KIA SP-II and SP-III , Toyota/Lexus Type T, T-III and T-IV , Honda/Acura ATF-Z1 (except in CVTs) , Mercedes Benz NAG1 , Volvo passenger car (except AW-1), and Volkswagen/Audi TL52162. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.

Product Features:

• Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Valvoline High Performance Gear Oil is an extreme pressure gear lubricant formulated with quality base oils and superior additives that helps protect against severe temperatures, shock loads, scuffing, scouring, corrosion and pitting in high speed, high load, high torque and high horsepower conditions.

Product Features:

• Formulated for reliable gear protection
• Protects against severe temperatures to help extend service life
• Formulated with extreme-pressure additives to minimize gear wear from shock loads
• Helps protect against gear wear from scuffing, scouring, corrosion and pitting
• Recommended for conventional hypoid differentials and non-synchronized manual transmissions in passenger cars, light trucks, sport utility vehicles, vans and heavy-duty trucks where an API-GL5 or GL-4 fluid is specified
• PLEASE NOTE: Valvoline recommends SynPower Full Synthetic Gear Oil for limited slip differentials

Prestone® Power Steering Fluid + Stop Leak (PSF+SL) delivers increased system life and prevents & stops system leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. The stop leak additives also prevent leaks by rejuvenating seals before they leak. Also designed with Anti-wear System Protection, Prestone PSF+SL protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 50,000 Mile Fluid Life
• Includes Stop Leak Additives to prevent and stop power steering system leaks.
• Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber & gasket components.
• Conventional Formula – For use in all manufacturers

Prestone® MAX European Vehicles Power Steering Fluid (PSF) + Stop Leak maximizes and increases system life + the power to stop leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. This formula is also great at preventing leaks by rejuvenating seals before they leak. This synthetic fluid is designed with 2X Anti-wear System Protection, which means more protection against pump failure, squeals and clogs. 100,000 mile fluid life, 2X more than conventional fluid, extends the time between replacement. This fluid is formulated for European vehicle manufacturers: Audi, BMW, Jaguar, Mini, Porsche, Mercedes, Saab, Volvo, Volkswagen and others. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 100,000 Mile Fluid Life. Synthetic Formula for longer life and more protection
• MAX + Stop Leak. Stop Leak Additives to prevent and stop power steering system leaks.
• For use in European vehicle manufacturers: Audi, BMW, Jaguar, Mini, Porsche, Mercedes, Saab, Volvo, Volkswagen and others
• 2X Anti-Wear Protection for enhanced System Life vs. conventional fluid. More protection against pump failure, squeals and clogs

Certified A/C Pro R-134a PAG 46 Refrigerant Oil with ICE 32. This product contains approximately 8 fluid ounces of PAG refrigerant oil with ICE32. Low viscosity PAG oil for R-134a auto A/C systems; ISO 46 viscosity. R-134a PAG 46 AC Oil Lubricant: with ICE 32 Lubricant Enhancer features advanced chemistry to help extend compressor life and improve cooling capacity. The PAG oil helps quiet noisy compressors. Meets OEM specifications.

Product Features:

• Low viscosity PAG oil for R-134a auto A/C systems; ISO 46 viscosity
• ICE32 Lubricant Enhancer: advanced chemistry to help extend compressor life and improve cooling capacity
• Meets OEM specifications

Only compatible with R134a refrigerant; Tools required for installation; Plastic bottle; Universal applications

Pennzoil motor oil, America’s most trusted motor oil, is an advanced proprietary conventional formula with active cleansing agents that is engineered to help clean up sludge in your engine. It provides a balance between reducing frictional losses and protection against harmful engine wear by getting between moving parts to prevent them from touching. It exceeds the stringent engine protection standards required by ILSAC GF-5 and API SN and is specially formulated to provide protection against the harmful effects of stop-and-go driving, and low-speed pre-ignition (LSPI) in modern turbocharged engines.

Product Features:

• Contains an active cleansing technology to help clean out sludge lesser motor oils leave behind
• No leading conventional oil provides better wear protection by preventing metal-on-metal contact
• Helps protect against the effects of low speed pre-ignition (LSPI) in modern turbocharged engines
• Contains a proprietary formulation that is designed to reduce friction between moving engine parts
• Specifications, Approvals and Recommendations: FCA MS-6395 and Ford WSS-M2C946-B1
• Exceeds the requirements of the following industry specifications: API SN PLUS, API SN-RC and all previous categories; ILSAC GF-5
• For a full list of equipment approvals and recommendations, please consult your local Shell Technical Help Desk and always consult your owner’s manual.

Royal Purple HMX SAE 5W-30 High-Mileage Synthetic Motor Oil, 5 quart is specifically designed to minimize wear and restore lost performance in engines with more than 75,000 miles. Formulated with robust zinc/phosphorus anti-wear compounds combined with Royal Purple’s proprietary additive technology Synerlec, HMX is chemically enhanced to revitalize hardened seals, reducing oil consumption common in high-mileage engines. In addition, HMX is fortified with stout detergents to remove engine build-up and deposits, maintain cleanliness and promote engine longevity. 

Product Features:

• Specifically designed to minimize wear and restore lost performance in engines with more than 75,000 miles
• Formulated with robust zinc/phosphorus anti-wear compounds combined with Royal Purple’s proprietary additive technology
• HMX is chemically enhanced to revitalize hardened seals, reducing oil consumption common in high-mileage engines
• Reduces friction and metal-to-metal contact for peak engine performance
• Also provides outstanding oxidation resistance to safely extend oil drain intervals, and an ionic attraction to metal surfaces, providing protection and minimizing wear at start-up

Automatic Transmission Fluid – 1 Liter and with High Performance

Valvoline SAE 75W-90 Full Synthetic Gear Oil provides the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Engineered to outperform, our detergent package-based formulation contains Full Synthetic basestocks and special additives that help protect parts from rust and corrosion while providing exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity, wear resistance additives that assist in protecting gear teeth, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. Valvoline SAE 75W-90 Full Synthetic Gear Oil is recommended for use in axle applications requiring factory-fill or drain-and-fill levels for limited slip performance. Protect your gears with Valvoline, the #1 gear oil brand.

Product Features:

• EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION , ranging from -30F to 300F degrees
• REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
• FIGHTS CORROSION AND RUST with emulsifying agents and safeguards against impurities, oxidation and thermal breakdown
• MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP HYPOID DIFFERENTIALS where APPI GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4 or MT-1 fluid
• MEETS OR EXCEEDS THE PERFORMANCE REQUIREMENTS for Mack GO-H and GO-J; API GL-5 and API MT-1; MIL-PRF-2105E; and SAE J2360

We’ve squeezed innovation into every ounce of Valvoline FlexFill SAE 75W-90 Full Synthetic Gear Oil, the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Our unique new flexible pouch makes getting into the tightest places to lubricate gears easier than ever and with less waste. The superior detergent package-based formulation contains fully synthetic basestocks and special additives that help protect parts from rust and corrosion while providing exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity, wear resistance additives that assist in protecting gear teeth, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. Valvoline FlexFill SAE 75W-90 Full Synthetic Gear Oil is recommended for use in axle applications requiring factory-fill or drain-and-fill levels for limited slip performance.

Product Features:

• FLEXIBLE POUCH FOR EASIER USE WITH LESS WASTE in tight, hard to reach undercarriage situations
• EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -30F to 300F degrees for dependable coverage year-round
• REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
• MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4 or MT-1 fluid
• MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Mack GO-H and GO-J; API GL-5 and API MT-1; MIL-PRF-2105E; and SAE J2360

Prestone® DOT 3 Motor Vehicle Brake Fluid delivers enhanced performance vs. DOT standards, benefitting all vehicles calling for DOT 3. This synthetic fluid starts with a higher dry boiling point than the DOT minimum standard to protect against overheating, brake fade and performance decline due to water absorption. This extended life (50,000 mile) fluid is also formulated to prevent corrosion of all metals within the braking system.  This formula is safe to use in all DOT 3 braking systems (ABS, disc or drum) and can mix with any DOT 3 fluid.  It is recommended to only use the DOT fluid specified for your car, as using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 50,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with High Grade Formula*
• Protects against performance decline due to water absorption. Prevents corrosion of all metals within the braking system.
• Synthetic, Extended Fluid Life Formula

Prestone® MAX DOT 3 Motor Vehicle Brake Fluid is our highest grade formula, maximizing performance vs. DOT standard. Prestone MAX is our best brake fluid at protecting against overheating and brake fade. With 100,000 mile fluid life, our longest life fluid has 2X more miles between replacement than regular Prestone DOT 3. Prestone MAX has superior performance in severe braking conditions when compared to regular Prestone DOT 3, which means even more piece of mind about the braking system. This synthetic fluid starts with our highest dry boiling point giving our best protection against performance decline due to water absorption. Prestone MAX DOT 3 is safe to use in all DOT 3 braking systems, ABS, disc or drum, and can mix with any DOT 3 fluid. Mixing Prestone MAX with other fluids will lower the performance rating for miles and boil points, for best results replace completely with Prestone MAX DOT 3. It is recommended to only use the DOT fluid specified for your car. Using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 100,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with Our Highest Grade Formula. Prevents corrosion of all metals within the braking system.
• Superior Protection in Extreme Braking Conditions
• Synthetic, Long Life Formula – 2X Longer than regular Prestone DOT 3