Ford Bronco Ignition Coils and Boots

The traditional ACCEL combination of yellow wire and red spark plug boots has been added to these SuperStock Spiral Core 5000 Series wire sets, which feature color-matched wire and spark plug boots in blue, black, and red. With only 500 ohms/ft. of resistance, more ignition energy can reach the spark plug, producing a longer-lasting, hotter spark flame kernel. The results is higher performance through improved efficiency, quicker throttle response, and reduced emissions. This 8mm wire’s double silicone construction is rated to 550 degrees F. The high-gloss wire jacket resists moisture, chemicals, and heat extremes for longer life and great looks. The fiberglass braid adds greater pull strength and terminal retention, while the stainless steel spark plug terminals provide excellent long life, electrical conductivity, and corrosion resistance. Both universal and custom-fit applications are available for early and late model cars and trucks.

Product Features:

• 500 Ohms/ft Of Resistance
• 550 F Rated Silicone Jacket
• Stainless Steel Plug Terminals
• High RFI Suppression For Street And Strip Use
• Universal And Import Coverage
• High-strength Fiberglass Braid Construction
• Pre And Post HEI Vehicles
• 8mm High Gloss Silicone Jacket

ACCEL’s SuperStock 4000 series spark plug wire sets are designed to upgrade an OE ignition system for high-spark delivery levels for street driven applications. The 450 degree F rated silicone jacket is extruded over a tightly woven, rugged fiberglass braid. The braid is applied over high dielectric strength EPDM (Ethylene Propylene Diene Monomer) inner insulation for ignition wire performance that exceeds SAE specifications.

Product Features:

• 7mm And 8mm High Gloss Silicone Jacket
• 450 F Rated Silicone Jacket
• Stainless Steel Plug Terminals
• RFI Suppression For Street Driven Applications
• Custom-fit Universal And Import Coverage
• High-strength Fiberglass Braid Construction
• Pre And Post HEI Vehicles

DENSO First Time Fit Ignition Wire Sets are identical in form fit color and performance to the factory-installed wire sets. Every part of each wire sets construction meets or exceeds OE/OES standards.

Product Features:

• Each wire is pre-cut to exact length so the wire set is ready to install right out of the box
• Identical OE end caps are designed to “click” into place for easy installation and a secure fit
• Strong connections – through a patented process, the terminals are attached to provide an extremely strong connection, ensuring the cable and boot will not separate during removal and installation

The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.

Product Features:

• Helically wound conductor suppresses electro and radio noise
• Kevlar core combination for great strength and durability
• Heavy Duty Terminals For Secure Connection
• 8mm silicone and synthetic jacket resists heat and abrasion
• 500 Ohms/ft. Resistance For Improved Spark Delivery And Power
• Silicone Boots Protect Against High Exhaust Temps

The Motorcraft Ignition wire set is a direct fit OEM replacement that guarantees the same performance and quality provided by the vehicle manufacturer.

Product Features:

• OEM quality
• OEM connectors for easy Installation.
• Resistant to high temperatures, corrosion and vibration.
• Ignition noise suppressed.
• Reduces the chance of misfire
• Increases engine life
• Protects against wire set failure

These ACCEL wire sets are a true performance upgrade replacement for OE types. Efficient delivery of spark energy for a good price. Silicone boots with black wire contain zinc-plated steel terminals. Noise suppression core. Set contains 8 plug wires with coil lead.

Product Features:

• 7mm And 8mm High Gloss Silicone Jacket
• 450° F Rated Silicone Jacket
• Stainless Steel Plug Terminals
• RFI Suppression For Street Driven Applications
• Custom-fit Universal And Import Coverage
• High-strength Fiberglass Braid Construction

Top off your GM ignition system with these great new replacement coils. The GM coils have MSD performance in factory style housings. MSD designed these coils by combining our blaster coil experience with e-core coil efficiency. Each coil has a unique turns ratio plus there is lower primary resistance than the stock coil. This all amounts to a bolt-in replacement coil that produces more output voltage. The coils will work with stock ignition systems as well as MSD equipped cars and trucks. Installation tip: If you plan to install an MSD ignition with your GM dual connector coil, use PN 8876 harness for a direct plug-in installation.

Product Features:

• Direct performance replacement for Ford TFI coil
• 85:1 turns ratio
• Lower Primary Resistance Produces High Voltage Output
• Works w/Stock Ignition As Well As MSD Ignitions
• CARB E.O. Approved

Carquest Premium ignition coils meet or exceed original equipment (OE) specifications and are developed by top OE/OES manufacturers to ensure superior performance. All of our Carquest Premium ignition coils are developed by IATF 16949 certified manufacturers for consistent durability and long-lasting performance. These ignition coils use high-quality components and will utilize optimized designs on applications where the OE ignition coil had frequent failures. We require stringent testing standards to ensure proper fit and performance for each application and stand behind our Carquest Premium ignition coils with an industry-leading warranty. Carquest Premium ignition coils are part of our Carquest Vehicle Solutions, which is a full line of engine management and electronics products that help control ignition, fuel delivery and emission systems. Carquest Vehicle Solutions are OE-quality parts designed, engineered and tested by world-class manufacturers to ensure a reliable and long-lasting repair.

Product Features:

• Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the part design process ensures speed-to-market and a precise fit guaranteed.
• 100% pure copper precision-wound windings increase coil life and ensure reliability and maximum coil output when needed.
• Highly conductive aluminum alloy secondary terminal guarantees secondary coil terminals will not oxidize (rust), will provide excellent conductivity, extended coil life and will not cause excessive stress on the primary control circuit.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure confidence and product reliability, every time.

BWD® is an aftermarket leader, providing a premium line of engine management products. BWD® manufactures and distributes high technology critical components for late model domestic and import vehicles. BWD® is constantly evolving to give customers the competitive edge they need to compete in today’s ever-changing marketplace.

Product Features:

• Manufactured with copper windings and permanent magnets to ensure strong signal emission and improved performance
• High temperature enameled wires were specified for better insulation and performance
• A full E-Lam core of silicon steel and solid brass high voltage terminals protects against corrosion. Our ignition coils are built for maximum output voltage
• Primary and Secondary windings feature enamel magnet wire for the highest temperature rating in the aftermarket
• As a tier I manufacturer with engineering and design capabilities second to none, our ignition coils are made to the highest quality standards

Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, and crisper throttle response. Compatible with late model Ford EEC-IV computer controlled ignition system equipped with a TFI distributor. Direct OEM replacement. Can also be used with an ACCEL, Mallory, Crane, Holley or MSD capacitive discharge ignition system. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy efficiency and resists corrosion better than aluminum. High dielectric strength ACCEL Yellow over-molded housing.

Product Features:

• Direct Plug In Replacement Direct OE Fit
• Advanced Bobbin Technology
• Standard Motor Products SMP Fd-478
• MSD 5527
• Standard Motor Products SMP Fd-478
• MSD 5527
• Resists Shock And Vibration
• Resists Corrosion

Carquest Ignition Coils ensure fast starts, consistent engine performance and optimized fuel efficiency at an affordable cost.

Product Features:

• High output
• Long spark duration
• High dielectric strength
• Corrosion resistant connections
• High reliability
• Long service life

An ACDelco Professional, premium aftermarket Ignition Coil is a high quality replacement for many vehicles on the road today. It increases electrical system voltage to help ignite the air/fuel mixture as the starting and charging system starts the engine, maintains the battery’s charge, and provides power to the electrical accessories while the engine is running. An ACDelco Professional Ignition Coil uses pure copper windings to improve durability and provides higher resistance to internal shorts and dielectric breakdown. Because the number and shape of the laminations determine the output characteristics of an ignition coil, ACDelco ensures that the silicone steel plates surrounding the ignition coil correctly match the original part size and number. Since steel laminations work best when they are new, shiny, and clean, ACDelco laminations are coated to hinder corrosion and many feature molded plastic protection to help ensure that nothing is exposed. This premium aftermarket replacement ignition coil is manufactured to meet your expectations for fit, form, and function.

Product Features:

• High quality coated windings to improve durability and provide protection against internal shorts and dielectric breakdown
• Silicone steel plates surrounding the ignition coil correctly match the original part size and number exactly
• Laminations are coated to hinder corrosion and many feature molded plastic protection to help ensure that nothing is exposed
• Professional, premium aftermarket replacement
• Provides the performance and dependability you expect from ACDelco
• Manufactured to meet expectations for fit, form, and function

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

• Premium quality materials for longer service life
• Sealed connections (where applicable) to prevent environmental corrosion and performance issues
• Global coverage for import and/or domestic applications
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

BWD is an aftermarket leader, providing a premium line of engine management products. BWD manufactures and distributes high technology critical components for late model domestic and import vehicles. BWD is constantly evolving to give customers the competitive edge they need to compete in today’s ever-changing marketplace.

Product Features:

• Our ignition coils use 100% pure copper windings in the primary and secondary bobbins to improve durability and provide higher resistance to internal shorts and dielectric breakdown
• Our premium ignition coils consist of a special blended formula for the best performance, longest life and better heat dissipation
• A full E-Lam core of silicon steel and solid brass high voltage terminals protects against corrosion. Our ignition coils are built for maximum output voltage
• Primary and Secondary windings feature enamel magnet wire for the highest temperature rating in the aftermarket

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

• Premium quality materials for longer service life
• Sealed connections (where applicable) to prevent environmental corrosion and performance issues
• Global coverage for import and/or domestic applications
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

BWD is an aftermarket leader, providing a premium line of engine management products. BWD manufactures and distributes high technology critical components for late model domestic and import vehicles. BWD is constantly evolving to give customers the competitive edge they need to compete in today’s ever-changing marketplace.

Product Features:

• Our knock sensors are designed to respond to knock frequencies up to 1000 Hz accommodating shifts in engine knock frequency making it a more flexible sensor responding to correct engine knock over a broad range of vehicle conditions
• Manufacturing processes include an automated data acquisition system to continuously monitor the sensor output to ensure that it responds with appropriate voltage output at the specified frequency range
• All units are 100% tested using an accelerometer vibration test to ensure trouble-free operation
• Featuring the broadest sensor coverage in the market, we meet the service professionals needs with the highest quality product every time he opens the box
• BWD is a global manufacturer of original equipment ignition products, complete quality control is maintained through the manufacturing process from componentry to finished product

DENSO First Time Fit Ignition Wire Sets are identical in form fit color and performance to the factory-installed wire sets. Every part of each wire sets construction meets or exceeds OE/OES standards.

Product Features:

• Each wire is pre-cut to exact length so the wire set is ready to install right out of the box
• Identical OE end caps are designed to “click” into place for easy installation and a secure fit
• Strong connections – through a patented process, the terminals are attached to provide an extremely strong connection, ensuring the cable and boot will not separate during removal and installation