Chevrolet Trailblazer Ext Fluids and Chemicals

Prestone® Power Steering Fluid (PSF) delivers increased system life. Designed with Anti-wear System Protection, Prestone PSF protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 50,000 Mile Fluid Life
• Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber & gasket components.
• For use in all manufacturers
• Conventional Formula – For use in all manufacturers

Specifications: Meets Dexron®, Dexron II-D®, II-E®, or Dexron III®, Ford Type-F, Mercon, or M2C138-CJ Volume: 1 US Quart Lightweight fluid avoids power losses, improves wear protection, resists thermal breakdown, evaporation and foaming, provides continued high pump output, and is suitable for most power steering units. RED LINE POWER STEERING FLUID satisfies the service fill requirements of most auto manufacturers and can be used where the manufacturer calls for any automatic transmission fluid such as Dexron®, Dexron II-D®, II-E®, or Dexron III®, Ford Type-F, Mercon, or M2C138-CJ such as required by Ford, AMC, Toyota, Nissan, Lexus, Infiniti, Jaguar, VW, Mercedes-Benz, BMW, SAAB, Subaru, Volvo, Porsche, Mitsubishi, Mazda, and many others. This fluid also satisfies power steering units requiring GM PN 1050017 or 1052884 (Spec Number 9985010), Chrysler Spec Number 5931, and Ford Spec Number M2C33-F. It also satisfies the hydraulic specifications of Denison HF-O, Vickers vane pumps, and Sundstrand piston pumps. REDLINE POWER STEERING FLUID

Product Features:

• Improved wear protection, resists thermal breakdown, evaporation and foaming
• Provides continued high pump output, suitable for most power steering units
• Lightweight fluid avoids power losses
• 50% greater high-temp viscosity and 1/5 of the high-temp evaporation
• Greater heat resistance helps to prevent boil-over
• Helps to prevent high-temp steering fade and difficult effort steering at low temps
• Compatible with petroleums and synthetics
• 1/4 of the oxidation of petroleum power steering fluids
• Helps prevent leakage and squealing

Valvoline DEXRON-VI/MERCON LV ATF is a full-synthetic transmission fluid formulated with advanced additive technology to meet and exceed the requirements of the General Motors DEXRON-VI specification. It is officially licensed and approved by GM and is fully back-serviceable and can be used wherever DEXRON-II and/or DEXRON-III are recommended. Recommended for use in the following applications: DEXRON-VI, DEXRON-III, DEXRON-II, MERCON LV and Allison C-4.

Product Features:

• Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Mobil 1 Synthetic ATF is a multi-vehicle, fully synthetic automatic transmission fluid that helps to improve overall transmission durability and cleanliness. Has exceptional thermal and oxidation stability and long-term frictional properties that help to improve and extend transmission efficiency, smooth shifting performance, and fuel economy. Mobil 1 ATF provides excellent low-temperature fluidity to promote reliable lubrication at temperatures down to -51C, and exceptional shear stability to help supports viscosity retention under the most severe heavy-duty, high-temperature operating conditions. Compatibile with mineral ATF fluids and all common seal materials to help provide excelent leakage control and reduce concern in top-off emergencies. Meets or exceeds the requirements of JASO 1-A and Ford MERCON V.

Product Features:

• Multi-vehicle, fully synthetic automatic transmission fluid that helps to improve overall transmission durability and cleanliness
• Exceptional thermal and oxidation stability to improve and extend transmission efficiency, smooth shifting performance, and fuel economy
• Excellent high and low-temperature fluidity to help support viscosity retention under extreme, heavy-duty operating conditions
• Compatibile with mineral ATF fluids and all common seal materials to help provide excelent leakage control
• Meets or exceeds the requirements of JASO 1-A and Ford MERCON V
• Manufacturer Part Number: 112980

Certified A/C Pro R-134a PAG 46 Refrigerant Oil with ICE 32. This product contains approximately 8 fluid ounces of PAG refrigerant oil with ICE32. Low viscosity PAG oil for R-134a auto A/C systems; ISO 46 viscosity. R-134a PAG 46 AC Oil Lubricant: with ICE 32 Lubricant Enhancer features advanced chemistry to help extend compressor life and improve cooling capacity. The PAG oil helps quiet noisy compressors. Meets OEM specifications.

Product Features:

• Low viscosity PAG oil for R-134a auto A/C systems; ISO 46 viscosity
• ICE32 Lubricant Enhancer: advanced chemistry to help extend compressor life and improve cooling capacity
• Meets OEM specifications

Only compatible with R134a refrigerant; Tools required for installation; Plastic bottle; Universal applications

Certified A/C Pro R-134a PAG 150 Refrigerant Oil with ICE 32. This product contains approximately 8 fluid ounces of PAG refrigerant oil with ICE32. High viscosity PAG oil for R-134a auto A/C systems; ISO 150 viscosity. R-134a PAG 150 AC Oil Lubricant with ICE32 Lubricant Enhancer features advanced chemistry to help extend compressor life and improve cooling capacity. The PAG oil helps quiet noisy compressors. Meets OEM specifications.

Product Features:

• High viscosity PAG oil for R-134a auto A/C systems; ISO 150 viscosity
• ICE32 Lubricant Enhancer: advanced chemistry to help extend compressor life and improve cooling capacity
• Meets OEM specifications

Castrol Transmax ATF/CVT Universal is a technologically advanced full-synthetic formulation designed to deliver excellent performance in most of the traditional stepped automatic transmissions and Continuously Variable Transmissions currently in use. It is also suitable for use in hybrids.

Product Features:

• Coverage of over 300 specs/95% of vehicles in operation
• Broad scope of vehicle applications improves workshop efficiency and inventory management
• Enhanced friction durability for smooth transmission performance
• Superior high temperature protection to effectively resist oxidation

Castrol Transmax High Mileage is specially formulated for transmissions with over 75,000 miles to deliver superior performance for maximum transmission life. It features additional seal conditioners to help stop leaks and cleaning agents to reduce varnish and deposit formation. It also protects against clutch wear and restores smooth shifting and can be used in a wide variety of specifications including DEXRON®-IIIH, MERCON® and JASO-1A.

Product Features:

• Additional seal conditioners help stop leaks.
• Extra cleaning agents reduce varnish and sludge formation.
• Protects against clutch wear and restores smooth shifting.
• Recommended for use in new & older vehicles that require:

Automatic transmission fluid is a technologically advanced, low viscosity formulation specially designed to deliver performance and maximum fuel efficiency for modern automatic transmissions.

Product Features:

• Full Synthetic, low viscosity formulation
• OEM approved and licensed by Ford (MERCON® LV) and GM (DEXRON® -VI)
• Low viscosity formula for maximum fuel efficiency in modern automatic transmissions
• Enhanced friction durability for smooth transmission performance
• Superior high temperature protection to effectively resist oxidation
• Unsurpassed protection against copper corrosion
• Industry Specifications and OEM Approvals: JASO-1A
• Licensed and approved for use in: All GM vehicles (DEXRON®-VI, All previous DEXRON®); All Ford vehicles which specify Mercon® LV

Prestone® DOT 3 Motor Vehicle Brake Fluid delivers enhanced performance vs. DOT standards, benefitting all vehicles calling for DOT 3. This synthetic fluid starts with a higher dry boiling point than the DOT minimum standard to protect against overheating, brake fade and performance decline due to water absorption. This extended life (50,000 mile) fluid is also formulated to prevent corrosion of all metals within the braking system.  This formula is safe to use in all DOT 3 braking systems (ABS, disc or drum) and can mix with any DOT 3 fluid.  It is recommended to only use the DOT fluid specified for your car, as using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 50,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with High Grade Formula*
• Protects against performance decline due to water absorption. Prevents corrosion of all metals within the braking system.
• Synthetic, Extended Fluid Life Formula

Prestone® MAX DOT 3 Motor Vehicle Brake Fluid is our highest grade formula, maximizing performance vs. DOT standard. Prestone MAX is our best brake fluid at protecting against overheating and brake fade. With 100,000 mile fluid life, our longest life fluid has 2X more miles between replacement than regular Prestone DOT 3. Prestone MAX has superior performance in severe braking conditions when compared to regular Prestone DOT 3, which means even more piece of mind about the braking system. This synthetic fluid starts with our highest dry boiling point giving our best protection against performance decline due to water absorption. Prestone MAX DOT 3 is safe to use in all DOT 3 braking systems, ABS, disc or drum, and can mix with any DOT 3 fluid. Mixing Prestone MAX with other fluids will lower the performance rating for miles and boil points, for best results replace completely with Prestone MAX DOT 3. It is recommended to only use the DOT fluid specified for your car. Using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 100,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with Our Highest Grade Formula. Prevents corrosion of all metals within the braking system.
• Superior Protection in Extreme Braking Conditions
• Synthetic, Long Life Formula – 2X Longer than regular Prestone DOT 3

We’ve squeezed innovation into every ounce of Valvoline FlexFill SAE 75W-90 Full Synthetic Gear Oil, the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Our unique new flexible pouch makes getting into the tightest places to lubricate gears easier than ever and with less waste. The superior detergent package-based formulation contains fully synthetic basestocks and special additives that help protect parts from rust and corrosion while providing exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity, wear resistance additives that assist in protecting gear teeth, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. Valvoline FlexFill SAE 75W-90 Full Synthetic Gear Oil is recommended for use in axle applications requiring factory-fill or drain-and-fill levels for limited slip performance.

Product Features:

• FLEXIBLE POUCH FOR EASIER USE WITH LESS WASTE in tight, hard to reach undercarriage situations
• EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -30F to 300F degrees for dependable coverage year-round
• REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
• MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4 or MT-1 fluid
• MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Mack GO-H and GO-J; API GL-5 and API MT-1; MIL-PRF-2105E; and SAE J2360

Pennzoil motor oil, America’s most trusted motor oil, is an advanced proprietary conventional formula with active cleansing agents that is engineered to help clean up sludge in your engine. It provides a balance between reducing frictional losses and protection against harmful engine wear by getting between moving parts to prevent them from touching. It exceeds the stringent engine protection standards required by ILSAC GF-5 and API SN and is specially formulated to provide protection against the harmful effects of stop-and-go driving, and low-speed pre-ignition (LSPI) in modern turbocharged engines.

Product Features:

• Contains an active cleansing technology to help clean out sludge lesser motor oils leave behind
• No leading conventional oil provides better wear protection by preventing metal-on-metal contact
• Helps protect against the effects of low speed pre-ignition (LSPI) in modern turbocharged engines
• Contains a proprietary formulation that is designed to reduce friction between moving engine parts
• Specifications, Approvals and Recommendations: FCA MS-6395 and Ford WSS-M2C946-B1
• Exceeds the requirements of the following industry specifications: API SN PLUS, API SN-RC and all previous categories; ILSAC GF-5
• For a full list of equipment approvals and recommendations, please consult your local Shell Technical Help Desk and always consult your owner’s manual.

Valvoline ATF+4® is a full-synthetic transmission fluid specifically engineered to protect and prolong the life of (FCA) Fiat Chrysler automatic transmissions. It is officially licensed and approved by FCA and is fully back-serviceable and can be used wherever ATF+3, ATF+2 or ATF+ is specified. Recommended for use in the following applications: Mopar ATF+ MS 7176®, ATF+2® MS 7176, ATF+3 and ATF+4.

Product Features:

• Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Help keep positraction chatter down with posi additive from Yukon Gear & Axle.

Product Features:

• positraction additive
• For use in any clutch-style limited slip

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• MAXLIFE TECHNOLOGY PREVENTS engine breakdown with 40% better wear protection than the industry standard
• REFRESH AGING SEALS AND PREVENT LEAKS with seal conditioners
• REDUCE SLUDGE, DEPOSITS, CORROSION, AND RUST with added detergents – keep motors clean inside
• ENHANCED FRICTION PERFORMANCE HELPS MAXIMIZE POWER with advanced friction-fighting agents
• MEETS OR EXCEEDS ALL REQUIREMENTS of ILSAC GF-6A, API SP, API SN with SN PLUS, API SN
• MaxLife Technology: Valvoline High Mileage with MaxLife Technology is specially formulated to maximize engine life in vehicles with over 75,000 miles, providing superior protection against wear, friction, heat, and deposits.
• Synthetic Blend Composition: This motor oil features a unique combination of synthetic and premium conventional oils, ensuring optimal performance and protection for high-mileage engines.

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• MAXLIFE TECHNOLOGY PREVENTS engine breakdown with 40% better wear protection than the industry standard
• REFRESH AGING SEALS AND PREVENT LEAKS with seal conditioners
• REDUCE SLUDGE, DEPOSITS, CORROSION, AND RUST with added detergents – keep motors clean inside
• ENHANCED FRICTION PERFORMANCE HELPS MAXIMIZE POWER with advanced friction-fighting agents
• MEETS OR EXCEEDS ALL REQUIREMENTS of ILSAC GF-6A, API SP, API SN with SN PLUS, API SN

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• MAXLIFE TECHNOLOGY PREVENTS engine breakdown with 40% better wear protection than the industry standard
• REFRESH AGING SEALS AND PREVENT LEAKS with seal conditioners
• REDUCE SLUDGE, DEPOSITS, CORROSION, AND RUST with added detergents – keep motors clean inside
• ENHANCED FRICTION PERFORMANCE HELPS MAXIMIZE POWER with advanced friction-fighting agents
• MEETS OR EXCEEDS ALL REQUIREMENTS of ILSAC GF-6A, API SP, API SN with SN PLUS, API SN
• MaxLife Technology: Valvoline High Mileage with MaxLife Technology is specially formulated to maximize engine life in vehicles with over 75,000 miles, providing superior protection against wear, friction, heat, and deposits.
• Synthetic Blend Composition: This motor oil features a unique combination of synthetic and premium conventional oils, ensuring optimal performance and protection for high-mileage engines.

Royal Purple HMX SAE 5W-30 High-Mileage Synthetic Motor Oil, 1 quart is specifically designed to minimize wear and restore lost performance in engines with more than 75,000 miles. Formulated with robust zinc/phosphorus anti-wear compounds combined with Royal Purple’s proprietary additive technology Synerlec, HMX is chemically enhanced to revitalize hardened seals, reducing oil consumption common in high-mileage engines. In addition, HMX is fortified with stout detergents to remove engine build-up and deposits, maintain cleanliness and promote engine longevity.

Product Features:

• Specifically designed to minimize wear and restore lost performance in engines with more than 75,000 miles
• Formulated with robust zinc/phosphorus anti-wear compounds combined with royal purple’s proprietary additive technology
• Hmx is chemically enhanced to revitalize hardened seals, reducing oil consumption common in high-mileage engines
• Reduces friction and metal-to-metal contact for peak engine performance
• Also provides outstanding oxidation resistance to safely extend oil drain intervals, and an ionic attraction to metal surfaces, providing protection and minimizing wear at start-up
• High-Mileage Formula: Specifically designed for engines with more than 75,000 miles, this full synthetic engine oil helps minimize wear and restore lost performance.

Prestone DEX-COOL (concentrate) antifreeze+coolant is specially designed to work with these specific vehicles: All GM® vehicles 1995 & newer (GM approved), most Ford® vehicles 2011 – 2018 and most Chysler® vehicles 2013 & newer. Prestone’s Antifreeze+Coolants are designed to the highest standards using state of the art technology. These fluids are designed to not only manage the engine temp and protect from freezing up, they also protect the engine from rust & corrosion. This fluid is designed to last 5yrs / 150,000 miles.

Product Features:

• Specially formulated to work with vehicles using orange colored fluid; HOAT. All GM 1995 & newer; Most Ford 2011-2018; Most Chrysler 2013 & newer
• 5 Yr., 150,000 mile Extended life formula
• Includes the Prestone protection package that protects against rust and corrosion of all cooling system metals, including aluminum.
• Concentrate formula. Must mix with distilled to the desired mix ratio of EG & water. Can be used for top-off, complete drain and refill or flush and refill of the cooling system.

PEAK ORIGINAL EQUIPMENT TECHNOLOGY ANTIFREEZE + COOLANT for NORTH AMERICAN VEHICLES is a line of premium coolants specifically designed to match the technology and color requirements of North American vehicles. Each coolant is formulated with the same corrosion inhibitor technology that protected your vehicle straight from the factory. Color cues on the packaging and a list of covered vehicles on the front label make it easy to identify the right match for your specific vehicle. PEAK ORIGINAL EQUIPMENT TECHNOLOGY ANTIFREEZE + COOLANT for NORTH AMERICAN VEHICLES – ORANGE is an extended life antifreeze/coolant based on proprietary state-of-the-art organic acid technology (OAT). The ethylene glycol-based formula represents a carefully balanced mixture of organic acid corrosion inhibitors for complete protection of modern high-performance North American vehicle engines. It can be mixed with any DEX-COOL approved formulations in newer GM, Opel, Daewoo and Saab vehicles, as well as with antifreeze/coolant in Ford and Chrysler vehicles requiring an orange type product. This product’s orange color distinguishes its unique chemistry and ensures easy selection for North American vehicles requiring this type and color of coolant. PEAK ORIGINAL EQUIPMENT TECHNOLOGY ANTIFREEZE + COOLANT for NORTH AMERICAN VEHICLES – ORANGE is free of silicate, borate, phosphate, nitrite, and amines, and is fully compatible with other extended life coolants. It meets the performance requirements of ASTM D3306 and D4985. When installed as part of a complete flush and coolant fill, PEAK guarantees this coolant will provide service life protection of up to 150,000 miles or 5 years.

Product Features:

• Matches technology and color requirements of North American OEMs specifying a Green Conventional coolant
• Protects all cooling system metals, including aluminum, against damaging rust and corrosion
• Compatible with other conventional green antifreeze + coolant formulations
• Easy-to-pour bottle with color-coding and vehicle applications listed on the front to simplify selecting the right antifreeze + coolant
• Available as both concentrate and 50/50 prediluted products to do the job right
• Testing Requirements: For proper freeze and boil over protection, use a traditional refractometer or hydrometer to measure the percentage of ethylene glycol by volume.

Prestone® Platinum antifreeze+coolant is Prestone’s best universal antifreeze & coolant product. GUARANTEED to work with all vehicles; all makes, models, years & fluid colors. 15+ years, 350,000 miles of protection; the fluid is guaranteed for the life of your vehicle. This advanced product delivers Extreme Protection against both freezing temperatures (-50 Deg. F) and overheating / boiling over of the engine (+268 Deg. F). Prestone Platinum utilizes industry leading protection from engine damaging rust, corrosion, buildup & scale. While ordinary antifreeze coolant only focuses on the basic corrosion coverage, Prestone Platinum goes farther, adding our most advanced cooling sytem protection, allowing the system to run optimally, like when it was new. Internal buildup & corrosion damage can cause engine part failure or clogging, leading to expensive repairs and inconveniences. Prestone Platinum helps you avoid costly repairs and vehicles in the shop. This extended life coolant is guaranteed to work with all new engines and engine technology, while also being backwards compatible, improving protection in all older engines. Prestone Platinum antifreeze+coolant – Year Round Protection.

Product Features:

• Guaranteed to work with All Vehicles. Universally works with all fluid colors; All OAT, POAT, HOAT & IAT; G05®, G11®, G12®, G12++®, G13®, G30®, G40®, & GG40®. For all engines & engine sizes, new and older engines.
• 15+ Yr., 350,000 mile Extended life formula. The fluid is guaranteed for the life of your vehicle
• Includes our most advanced Prestone Cor-Guard® technology, unmatched cooling system parts protection that protects against engine damage; rust, corrosion, scale, build-up and clogging. Protection for 15+yrs / 350,000 miles.
• Ready to Use formula – Prediluted 56/54. Perfect for small volume top-off or complete drain and refill of the cooling system

Prestone American Vehicles (Orange) antifreeze+coolant is specially designed to work with these specific vehicles: Ford 2002 and newer; Chrysler 2000 and newer; GM 1995 and newer. Prestone’s Antifreeze+Coolants are designed to the highest standards using state of the art technology. These fluids are designed to not only manage the engine temp and protect from freezing up, but they also protect the engine from rust, corrosion, buildup, pitting and engine damage. All of those can cause engine part failure and expensive repairs. Avoid costly repairs and vehicles in the shop with Prestone Asian vehicles antifreeze+coolant. This fluid is designed to last 10yrs / 300,000 miles and also to protect the internal parts of the engine for 10yrs / 300,000, offically patented by Prestone.

Product Features:

• Specially formulated to work with vehicles using multiple colors of fluid; OAT, HOAT, G05. Ford 2002 and newer; Chrysler 2000 and newer; GM (Chevrolet, Buick, GMC, Cadillac, Oldmobile, Pontiac, Saturn) 1995 and newer.
• Superior protection guarantee – 10 Yr., 300,000 mile Extended life formula
• Includes patented Prestone CorGuard technology, the best advancement in cooling system parts protection that protects against rust and corrosion of all cooling system metals, including aluminum. Protection for 300,000 miles.
• Ready to Use formula. Perfect for small volume top-off or complete drain and refill of the cooling system.

FRAM Orange Concentrate is formulated for cars and light duty trucks that use Orange extended life coolant. FRAM Orange Concentrate meets or exceeds ASTM D3306 and D4985 standards for corrosion protection, while providing reliable freeze-up and boil-over protection.

Product Features:

• Work with vehicles using orange colored fluid. 5 Yr., 150,000 mile Extended life formula.
• All GM« vehicles 1995 & newer /GM approved (GMC, Chevrolet, Buick, Cadillac, Pontiac, Saturn, Oldsmobile, Hummer), most Ford« vehicles 2011- 2018 (Ford, Lincoln, Mercury) and most Chrysler« vehicles 2013 & newer (Ram, Dodge, Jeep, Chrysler)
• All GM® vehicles 1995 & newer /GM approved (GMC, Chevrolet, Buick, Cadillac, Pontiac, Saturn, Oldsmobile, Hummer), most Ford® vehicles 2011- 2018 (Ford, Lincoln, Mercury) and most Chrysler® vehicles 2013 & newer (Ram, Dodge, Jeep, Chrysler)
• Meets or exceeds ASTM D3306 & D4985 for corrosion protection.
• Concentrated formula. Must mix with high quality (distilled/deionized) water to the desired ratio. Can be used for top-off, complete drain and refill or flush and refill of the cooling system.