2007 Mazda B4000 Fluids and Chemicals

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• Maxlife technology prevents engine breakdown with 40% better wear protection than the industry standard
• Refresh aging seals and prevent leaks with seal conditioners
• Reduce sludge, deposits, corrosion, and rust with added detergents – keep motors clean inside
• Enhanced friction performance helps maximize power with advanced friction-fighting agents
• Meets or exceeds all requirements of ilsac gf-6a, api sp, api sn with sn plus, api sn
• MaxLife Technology: The exclusive formula of Valvoline High Mileage with MaxLife Technology Engine Oil is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles.

Formulated to meet the specific requirements of Subaru vehicles equipped with conventional (non-CVT) transmissions up to model year 2005. Recommended for service-fill in all Subaru automatic transmissions where SUBARU ATF HP is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. IDEMITSU is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. IDEMITSU application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.

Product Features:

• Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
• Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
• Provides superior cleanliness, maintaining the transmission free of sludge and varnish deposits
• Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
• Advanced anti-wear technology provides maximum protection to gears and bearings

Give your higher mileage engine the care it deserves with Mobil 1 High Mileage full-synthetic motor oil 0W-20. This formula utilizes Mobil 1’s signature Triple Action Formula to deliver outstanding engine performance, protection, and cleanliness to vehicles with over 75,000 miles. Mobil 1 High Mileage motor oil extends engine life by reducing friction and preventing deposits and sludge buildup – keeping critical engine parts clean and protected for up to 10,000 miles between oil changes.(1) Mobil 1 helps to keep your engine running at lower temperatures(2) and is proven to cool engine temperatures by over 10%.(3) Mobil 1 High Mileage full-synthetic motor oil 5W-30 also helps control oxidation to prevent oil breakdown and is recommended by ExxonMobil for all types of modern cars, SUVs, light vans, and light trucks – including those with high-performance, turbocharged, supercharged, multi-valve, or fuel-injected engines. Mobil 1 is America’s No. 1 selling synthetic motor oil brand at retail, (4) trusted and recommended by car builders and experienced mechanics, and is the Official Motor Oil of NASCAR®. ((1)Protects for up to 10,000 miles or 1 year, whichever comes first. To learn more about the Mobil 1 Limited Warranty, visit Mobil.US. (2)Compared to conventional oil. (3) Based on proprietary engine testing¿results may vary. (4) Source: The NPD Group/ Retail Tracking Service/ Dollar Sales/ PCMO full-synthetic/ 52 weeks ending September 30, 2023)

Product Features:

• Mobil 1 High Mileage full-synthetic motor oil 5W-30 is designed for engines with over 75,000 miles to go up to 10,000 miles between oil changes. (1)
• Utilizes Mobil 1’s signature Triple Action Formula to deliver outstanding engine performance, protection, and cleanliness
• Meets ILSAC GF-6 standards to help provide low-speed pre-ignition (LSPI) and timing chain wear protection while keeping your engine clean and helping to improve your fuel economy
• Provides excellent internal engine heat protection (up to 500 degrees F) and low temperature protection (to -30 degrees F)
• Helps extend engine life by working to prevent damaging deposits and sludge buildup
• Manufacturer part number: 103767

Prestone® MAX DOT 3 Motor Vehicle Brake Fluid is our highest grade formula, maximizing performance vs. DOT standard. Prestone MAX is our best brake fluid at protecting against overheating and brake fade. With 100,000 mile fluid life, our longest life fluid has 2X more miles between replacement than regular Prestone DOT 3. Prestone MAX has superior performance in severe braking conditions when compared to regular Prestone DOT 3, which means even more piece of mind about the braking system. This synthetic fluid starts with our highest dry boiling point giving our best protection against performance decline due to water absorption. Prestone MAX DOT 3 is safe to use in all DOT 3 braking systems, ABS, disc or drum, and can mix with any DOT 3 fluid. Mixing Prestone MAX with other fluids will lower the performance rating for miles and boil points, for best results replace completely with Prestone MAX DOT 3. It is recommended to only use the DOT fluid specified for your car. Using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 100,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with Our Highest Grade Formula. Prevents corrosion of all metals within the braking system.
• Superior Protection in Extreme Braking Conditions
• Synthetic, Long Life Formula – 2X Longer than regular Prestone DOT 3

Prestone® DOT 3 Motor Vehicle Brake Fluid delivers enhanced performance vs. DOT standards, benefitting all vehicles calling for DOT 3. This synthetic fluid starts with a higher dry boiling point than the DOT minimum standard to protect against overheating, brake fade and performance decline due to water absorption. This extended life (50,000 mile) fluid is also formulated to prevent corrosion of all metals within the braking system.  This formula is safe to use in all DOT 3 braking systems (ABS, disc or drum) and can mix with any DOT 3 fluid.  It is recommended to only use the DOT fluid specified for your car, as using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 50,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with High Grade Formula*
• Protects against performance decline due to water absorption. Prevents corrosion of all metals within the braking system.
• Synthetic, Extended Fluid Life Formula

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• MAXLIFE TECHNOLOGY PREVENTS engine breakdown with 40% better wear protection than the industry standard
• REFRESH AGING SEALS AND PREVENT LEAKS with seal conditioners
• REDUCE SLUDGE, DEPOSITS, CORROSION, AND RUST with added detergents – keep motors clean inside
• ENHANCED FRICTION PERFORMANCE HELPS MAXIMIZE POWER with advanced friction-fighting agents
• MEETS OR EXCEEDS ALL REQUIREMENTS of ILSAC GF-6A, API SP, API SN with SN PLUS, API SN

Upgrading your motor oil to Valvoline Full Synthetic High Mileage with MaxLife Technology can help you increase the longevity of your car, truck or SUV with over 75,000 miles. It’s proven to protect your high-mileage motor against wear, friction, heat, and deposits – the leading causes of engine breakdown and expensive repairs. Our exclusive formulation goes beyond industry standards to protect your engine. It’s fortified with enhanced wear additives and friction-fighting agents to safeguard critical engine components, extra detergents to clean inside your engine, and premium seal conditioners to restore aging seals and prevent leaks. Superior viscosity modifiers and high-quality base oils help it perform exceptionally in both high and low temperatures. Engineered with ingenuity, tested with tenacity, and proven with purpose, our formula was innovated in America with a century and a half of hands-on experience from the original motor oil brand.

Product Features:

• Enhanced maxlife technology prevents engine breakdown in extreme conditions with 50% better wear protection than the industry standard
• Treat and prevent leaks with premium seal conditioners to keep oil out of places it shouldn’t be
• 25% extra defense against deposits, sludge, corrosion and rust via interior-cleansing detergents
• Extreme temperature protection through our high-quality base oils and superior viscosity modifiers
• Meets or exceeds all requirements of ilsac gf-6a, api sp, api sn with sn plus, api sn
• MaxLife High Mileage Synthetic Engine Oil is specially designed for engines with over 75,000 miles, providing ultimate protection against wear, friction, heat, and deposits.

PENTOSIN ATF 44 5L

Help keep positraction chatter down with posi additive from Yukon Gear & Axle.

Product Features:

• positraction additive
• For use in any clutch-style limited slip

Prestone® Power Steering Fluid + Stop Leak (PSF+SL) delivers increased system life and prevents & stops system leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. The stop leak additives also prevent leaks by rejuvenating seals before they leak. Also designed with Anti-wear System Protection, Prestone PSF+SL protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 50,000 Mile Fluid Life
• Includes Stop Leak Additives to prevent and stop power steering system leaks.
• Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber & gasket components.
• Conventional Formula – For use in all manufacturers

Prestone® Power Steering Fluid + Stop Leak (PSF+SL) delivers increased system life and prevents & stops system leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. The stop leak additives also prevent leaks by rejuvenating seals before they leak. Also designed with Anti-wear System Protection, Prestone PSF+SL protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 50,000 Mile Fluid Life
• Includes Stop Leak Additives to prevent and stop power steering system leaks.
• Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber & gasket components.
• Conventional Formula – For use in all manufacturers

Formulated to meet the specific requirements of Mazda vehicles equipped with conventional (non-CVT) transmissions that require the use of Mazda Type M3 and M5 ATF. Recommended for service-fill in all Mazda automatic transmissions where M5 or M3 ATF is specified. This fluid is also recommended for certain Ford vehicles where M5 ATF is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. IDEMITSU is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. IDEMITSU application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.

Product Features:

• Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
• Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
• Provides superior cleanliness, maintaining the transmission free of sludge and varnish deposits
• Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
• Advanced anti-wear technology provides maximum protection to gears and bearings

Antifreeze Conventional Green 50/50 is an ethylene glycol-based product for use in car and light duty trucks that are already using a conventional coolant. The inhibitors prevent rust, corrosion, and provide freeze-up and boil-over protection. Prime Green 50/50 can be used to top-off cooling systems in vehicles using conventional AF/C, will not harm rubber parts, and meets ASTM D3306 and D4985 standards.

Product Features:

• Low Silicate Formula.
• When used as directed, will provide protection for a minimum of 1 year
• Meets or exceeds ASTM requirements for cars, light duty trucks
• Ready to Use formula (prediluted to a 50% Eg & 50% distilled water mix). Perfect for small volume top-off or complete drain and refill of the cooling system

Prestone® Platinum antifreeze+coolant is Prestone’s best universal antifreeze & coolant product. GUARANTEED to work with all vehicles; all makes, models, years & fluid colors. 15+ years, 350,000 miles of protection; the fluid is guaranteed for the life of your vehicle. This advanced product delivers Extreme Protection against both freezing temperatures (-50 Deg. F) and overheating / boiling over of the engine (+268 Deg. F). Prestone Platinum utilizes industry leading protection from engine damaging rust, corrosion, buildup & scale. While ordinary antifreeze coolant only focuses on the basic corrosion coverage, Prestone Platinum goes farther, adding our most advanced cooling sytem protection, allowing the system to run optimally, like when it was new. Internal buildup & corrosion damage can cause engine part failure or clogging, leading to expensive repairs and inconveniences. Prestone Platinum helps you avoid costly repairs and vehicles in the shop. This extended life coolant is guaranteed to work with all new engines and engine technology, while also being backwards compatible, improving protection in all older engines. Prestone Platinum antifreeze+coolant – Year Round Protection.

Product Features:

• Guaranteed to work with All Vehicles. Universally works with all fluid colors; All OAT, POAT, HOAT & IAT; G05®, G11®, G12®, G12++®, G13®, G30®, G40®, & GG40®. For all engines & engine sizes, new and older engines.
• 15+ Yr., 350,000 mile Extended life formula. The fluid is guaranteed for the life of your vehicle
• Includes our most advanced Prestone Cor-Guard® technology, unmatched cooling system parts protection that protects against engine damage; rust, corrosion, scale, build-up and clogging. Protection for 15+yrs / 350,000 miles.
• Ready to Use formula – Prediluted 56/54. Perfect for small volume top-off or complete drain and refill of the cooling system

All Anitfreeze + Coolants are not the same. Prestone® MAX antifreeze + coolant is GUARANTEED to provide MAXIMUM ENGINE PROTECTION in all Vehicle Makes, Models & Years. It delivers the widest range of temperature protection, industry leading protection from engine damaging rust & corrosion and the longest lasting protection in the industry. Trust Prestone for maximum, year-round engine protection.

Product Features:

• Can top off or replace all antifreeze + coolant colors and formulations in all Vehcile Makes, Models & Years – Guranteed.
• Our patented, advance formula provides extreme temperature protection from the worst of winter deep freezes and scorching summer heat.
• We deliver industry leading protection from engine damaging rust, corrosion & buildup. Prestone MAX completely stops the formation of rust & corrosion for better engine performance and longer engine life.
• Prestone Max is guaranteed to protect your vehicle for 15+ years and/or 350,000 miles. It¿s the longest fluid life in the industry.
• Prestone Max is guaranteed to protect your vehicle for 15+ years and/or 350,000 miles. It┐s the longest fluid life in the industry.
• This is a Ready to Use formula – prediluted 56/44.

Prestone® Platinum antifreeze+coolant is Prestone’s best universal antifreeze & coolant product. GUARANTEED to work with all vehicles; all makes, models, years & fluid colors. 15+ years, 350,000 miles of protection; the fluid is guaranteed for the life of your vehicle. This advanced product delivers Extreme Protection against both freezing temperatures (-50 Deg. F) and overheating / boiling over of the engine (+268 Deg. F). Prestone Platinum utilizes industry leading protection from engine damaging rust, corrosion, buildup & scale. While ordinary antifreeze coolant only focuses on the basic corrosion coverage, Prestone Platinum goes farther, adding our most advanced cooling sytem protection, allowing the system to run optimally, like when it was new. Internal buildup & corrosion damage can cause engine part failure or clogging, leading to expensive repairs and inconveniences. Prestone Platinum helps you avoid costly repairs and vehicles in the shop. This extended life coolant is guaranteed to work with all new engines and engine technology, while also being backwards compatible, improving protection in all older engines. Prestone Platinum antifreeze+coolant – Year Round Protection.

Product Features:

• Guaranteed to work with All Vehicles. Universally works with all fluid colors; All OAT, POAT, HOAT & IAT; G05®, G11®, G12®, G12++®, G13®, G30®, G40®, & GG40®. For all engines & engine sizes, new and older engines.
• 15+ Yr., 350,000 mile Extended life formula. The fluid is guaranteed for the life of your vehicle
• Includes our most advanced Prestone Cor-Guard® technology, unmatched cooling system parts protection that protects against engine damage; rust, corrosion, scale, build-up and clogging. Protection for 15+yrs / 350,000 miles.
• Concentrated formula. Must mix with high quality water to the desired ratio. Can be used for top-off, complete drain and refill or flush and refill of the cooling system.

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

• Fits Ford 8.8″ with 28 spline axles
• 4-spring, clutch style positraction
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Certified A/C Pro R-134a PAG 46 Refrigerant Oil with ICE 32. This product contains approximately 8 fluid ounces of PAG refrigerant oil with ICE32. Low viscosity PAG oil for R-134a auto A/C systems; ISO 46 viscosity. R-134a PAG 46 AC Oil Lubricant: with ICE 32 Lubricant Enhancer features advanced chemistry to help extend compressor life and improve cooling capacity. The PAG oil helps quiet noisy compressors. Meets OEM specifications.

Product Features:

• Low viscosity PAG oil for R-134a auto A/C systems; ISO 46 viscosity
• ICE32 Lubricant Enhancer: advanced chemistry to help extend compressor life and improve cooling capacity
• Meets OEM specifications

Only compatible with R134a refrigerant; Tools required for installation; Plastic bottle; Universal applications

Valvoline MaxLife Multi-Vehicle Automatic Transmission Fluid (ATF) is a full-synthetic formulation with advanced additives to prevent the major causes of transmission breakdown and help extend transmission life.  Developed to help prevent leaks, maximize transmission performance, reduce transmission wear, and maintain smooth shifting longer than conventional fluids. It is suitable for use in a broad range of ATF applications including most Ford, GM, Toyota, Honda, Nissan, Hyundai, BMW, Mercedes, Volvo, VW & Audi.

Product Features:

• Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
• Long life friction modifiers help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
• High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks in high mileage transmissions
• Developed with anti-wear technology to help improve transmission durability
• Advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures
• Suitable for 95% of traditional ATFs including Dex/Merc, Mercon LV & Mercon V

Castrol Transmax High Mileage is specially formulated for transmissions with over 75,000 miles to deliver superior performance for maximum transmission life. It features additional seal conditioners to help stop leaks and cleaning agents to reduce varnish and deposit formation. It also protects against clutch wear and restores smooth shifting and can be used in a wide variety of specifications including DEXRON®-IIIH, MERCON® and JASO-1A.

Product Features:

• Additional seal conditioners help stop leaks.
• Extra cleaning agents reduce varnish and sludge formation.
• Protects against clutch wear and restores smooth shifting.
• Recommended for use in new & older vehicles that require:

FRAM DEX III/MERC ATF is formulated for older model Ford and General Motors  vehicles requiring MERCON®, DEXRON-I®, DEXRON-II® and DEXRON-III®. It is also  recommended for transmissions, power steering systems, and hydraulic systems  requiring a DEXRONIII® or Caterpillar TO-2 fluid. FRAM DEX III/MERC ATF may also  be used in compressors, pumps, and hydraulic systems. FRAM DEX III-H/M ATF is  recommended for use in all transmissions, hydraulic systems, and power steering units  manufactured by American, European, Korean, Japanese and other manufactures from  around the world specifying DEXRON®III H/Mercon® and earlier DEXRON®/Mercon® type transmission fluids.

Product Features:

• Good foam and corrosion prevention
• Safe for seals
• Promotes smooth shifting
• ALWAYS REFER TO YOUR VEHICLES OPERATING MANUAL TO SELECT THE CORRECT GRADE FLUID FOR YOUR TRANSMISSION
• TRANSMISSION FLUIDS ALSO APPLICABLE IN POWER STEERING UNITS; CHECK OWNERS’ MANUAL

Formulated to meet the specific requirements of Toyota, Lexus, and Scion vehicles equipped with conventional (non-CVT) transmissions that require the use of ATF T-IV. Recommended for service-fill in all Toyota, Lexus, and Scion automatic transmissions whe

Product Features:

• Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
• Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
• Provides superior cleanliness, maintaining the transmission free of sludge and varnish deposits
• Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
• Advanced anti-wear technology provides maximum protection to gears and bearings
• Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking

FRAM DEX III/MERC ATF is formulated for older model Ford and General Motors  vehicles requiring MERCON®, DEXRON-I®, DEXRON-II® and DEXRON-III®. It is also  recommended for transmissions, power steering systems, and hydraulic systems  requiring a DEXRONIII® or Caterpillar TO-2 fluid. FRAM DEX III/MERC ATF may also  be used in compressors, pumps, and hydraulic systems. FRAM DEX III-H/M ATF is  recommended for use in all transmissions, hydraulic systems, and power steering units  manufactured by American, European, Korean, Japanese and other manufactures from  around the world specifying DEXRON®III H/Mercon® and earlier DEXRON®/Mercon® type transmission fluids.

Product Features:

• Good foam and corrosion prevention
• Safe for seals
• Promotes smooth shifting
• ALWAYS REFER TO YOUR VEHICLES OPERATING MANUAL TO SELECT THE CORRECT GRADE FLUID FOR YOUR TRANSMISSION
• TRANSMISSION FLUIDS ALSO APPLICABLE IN POWER STEERING UNITS; CHECK OWNERS’ MANUAL

FRAM DEX III/MERC ATF is formulated for older model Ford and General Motors  vehicles requiring MERCON®, DEXRON-I®, DEXRON-II® and DEXRON-III®. It is also  recommended for transmissions, power steering systems, and hydraulic systems  requiring a DEXRONIII® or Caterpillar TO-2 fluid. FRAM DEX III/MERC ATF may also  be used in compressors, pumps, and hydraulic systems. FRAM DEX III-H/M ATF is  recommended for use in all transmissions, hydraulic systems, and power steering units  manufactured by American, European, Korean, Japanese and other manufactures from  around the world specifying DEXRON®III H/Mercon® and earlier DEXRON®/Mercon® type transmission fluids.

Product Features:

• Good foam and corrosion prevention
• Safe for seals
• Promotes smooth shifting
• ALWAYS REFER TO YOUR VEHICLES OPERATING MANUAL TO SELECT THE CORRECT GRADE FLUID FOR YOUR TRANSMISSION
• TRANSMISSION FLUIDS ALSO APPLICABLE IN POWER STEERING UNITS; CHECK OWNERS’ MANUAL

Castrol® Transmax DEX/MERC includes enhanced friction durability for smooth transmission performance. Designed for use in older Ford and GM vehicles.

Product Features:

• Enhanced friction durability for smooth transmission performance
• Meets DEXRON®-III H requirements; also satisfies requirements of DEXRON®, DEXRON®-III, IIE, and II; do not use this ATF in applications calling for DEXRON®-VI
• Meets MERCON® requirements; may also be used in power steering applications where MERCON® is required; use Castrol Type F ATF in applications calling for Type F
• Do not use this ATF in applications calling for MERCON® V or MERCON® SP