1998 Chevrolet C1500 Drivetrains

8.6″ GM standard Open side gear Thrust washer.

Product Features:

• Side gear thrust washer
• Fits GM 8.6″

Product Features:

• USA Standard Gear heavy-duty cross pin shaft
• Fits GM 8.5″ and 8.6″
• Works with Spartan Locker or standard open spider gears

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush. (includes Supershims)

Product Features:

• Fits GM 8.6″
• Included are a pinion seal, crush sleeve , complete shim kit, marking compound and brush.

8.5, 9.5, & 8.2 Buick, Oldsmobile, Pontiac GM REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

• Pinion Redi-sleeve
• Fits GM 8.5″, 9.5″ and 8.2″ Buick, Oldsmobile and Pontiac

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects. This unit has larger bearing journals for added strength & uses heavy-duty carrier bearings & races.

Product Features:

• Fits GM 8.5″ with 28 spline axles
• 2.73 ratio and up only
• 4-spring, clutch style positraction
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Differential Cover with Hardware Included

Pennzoil? Synchromesh Fluid is designed to offer optimal protection for moderately loaded gears in manual transmissions. Containing a high detergent additive system, it helps cope with water, dust, dirt, and any other small deposits you might encounter on or off-road(1). Pennzoil? Synchromesh Fluid also offers synchronizer compatibility for performance in manual transmissions, specifically to fulfill the needs of Chrysler, GM, Honda and other transmission requirements. Pennzoil? Synchromesh Fluid meets General Motors specification 9985648 for use where GM part numbers 12345349 or 12345577 are called out for use. Chrysler manual transmission fluid specification MS-9224 is also met. This high quality manual transmission fluid is formulated for good low temperature flow to maintain shift characteristics even after a cold night(2). Corrosion protection is added to help protect your transmission. Pennzoil? Synchromesh fluid is a manual transmission fluid designed for certain manual trans axles and manual transmissions used by general motors or Chrysler. (1)The Anglamol 6091 additive system contains approximately twice the sulfonate detergent levels as current generation PCMO, 4500 ppm as magnesium of magnesium sulfonate. This engine oil type additive will emulsify water and polar contamination sufficiently to handle contamination levels above 0.5% water. Anglamol 6091 – Detergent, friction modifier, extreme pressure agent, seal swell, anti-wear, anti-oxidant. Chemical Composition – Magnesium sulphonate, alkenyl amide, alkenyl ester sulphide, alkenyl phosphite, alkylbenzene, hecterocyclic ether, zinc dithiophosphate. (2)Pour point is less than -39 Deg. C. Low temperature viscosity in a -40 Deg. C Brookfield test of 50,000 cPs maximum, less than a 75W gear oil and the cold cranking viscosity less than a typical conventional SAE 5W engine oil.

Product Features:

• Excellent yellow metal compatibility
• Meets GM specification 9985648 and Chrysler specification MS-9224
• Excellent synchronizer performance
• Exhibits excellent low-temperature performance

This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

• Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models
• Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Yukon yoke for 8.5″ or 8.6″ GM (mech 3R) with a U/joint size and triple lip design. 2.556″ snap ring span, 1.125″ cap diameter. Inside snap ring. This yoke uses inside snap rings. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits GM 8.5″ and 8.6″
• 30 spline
• Mechanics 3R u-joint size
• 2.556″ snap ring span
• 1.125″ cap diameter
• Inside snap ring design
• Strap style

Product Features:

• Clutch kit
• Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
• 14 piece kit
• Carbon fiber clutches

Product Features:

• MINI INSTALL KIT-GM9.5/CHRY9.25 FRT

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Over 25 years ago, Belltech engineers developed one of the industry firsts that enabled the Sport Truck craze, the Belltech Drop Spindle. By relocating the wheel mounting point a.k.a. spindle pin higher on the spindle casting, our engineers were able to provide a 2 to 3 Inch lowering without affecting any other suspension or steering geometry, not even the shock absorber

Product Features:

• By Relocating The Wheel Mounting Point A.K.A. Spindle Pin Higher On The Spindle Casting
• Our Engineers Were Able To Provide A 2 To 3 Inch Lowering Without Affecting Any Other Suspension Or Steering Geometry, Not Even The Shock Absorber!
• Belltech Spindles Maintain Critical Suspension Geometry And Eliminate Excessive Ball Joint, Shock And Tire Wear Common To Other Methods Of Lowering
• Our Spindles Maintain Critical Suspension Geometry And Eliminate The Possibility Of Suspension Misalignment
• Each Spindle Is Built From High Strength Ductile Iron, Providing The Structural Integrity To Meet And Exceed All Factory Specification

Pinion Seal

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits 1997 and down GM 9.5″
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings

9.5″ GM cover gasket.

Product Features:

• Cover gasket
• Fits GM 9.5″

Yukon yoke for GM 8.5″ with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits GM 8.5″
• 30 spline
• 1310 u-joint size
• Outside snap ring design
• 3.219″ snap ring span
• 1.062″ cap diameter
• Strap style

U/joint strap bolt for 14T, 7.5″, and 8.5″ GM.

Product Features:

• u-joint strap bolt for GM 10.5″ 14 bolt truck, 7.5″ and 8.5″

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

• Fits GM 9.5″
• 4-spring, clutch style positraction
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Drive Shaft Center Support

C/Clip for Chrysler 8.25″, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 8.2″, 8.5″ & 8.6″.

Product Features:

• c-clip for Chrysler 8.25″, Ford 8.8″, GM 12 bolt car and truck and GM 8.2″, 8.5″ and 8.6″
• .150″ thick

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.6″, 12 bolt car and 12 bolt truck differential. This kit contains carrier bearings, races and shims.

Product Features:

• Fits GM 12 bolt passenger car and truck and 8.6″
• Includes carrier bearings and races and “super” carrier shim kit

8.5″ & 8.6″ GM standard Open pinion gear Thrust washer. also fits 8.5″ Eaton with 0.795″ cross pin.

Product Features:

• Pinion gear thrust washer for GM 8.5″ and 8.6″
• Fits standard open differentials only
• 0.795″ I.D.

This drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

• Direct replacement – this drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicle
• Ideal solution – this kit is a reliable replacement for original components that have failed due to fatigue
• Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.

Product Features:

• Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
• Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
• Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
• Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio