from

$373.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$429.99

The Edelbrock #38183 is a single-bore 90mm throttle body designed with a 5.0L Ford-style base pad. It is fully machined and assembled by Edelbrock. It includes a Throttle Position Sensor, a progressive throttle cable lever, and cruise and kick-down attach

from

$44.99

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$29.99

Product Features:

Timing Chain Only

from

$48.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PTFE offers the best in fluid and high-temperature compatibility and contact sealing surface can run on undersize shafts, seal minor imperfections and virtually eliminate shaft wear.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$188.99

Product Features:

9.5 in. Length
0.312 in. Diameter
4130 Chromoly Steel Material
Black Oxide Finish
Made In The USA

from

$59.19

High performance, race quality gasket with molded rubber coating over a steel core. Steel core provides rigidity and durability, preventing prevent push out while the molded rubber coating helps seal minor oil pan rail irregularities. The one piece design eliminates the need for separate end seals to make installation easier and even further reduce the possibility of oil leakage. Provides excellent sealing and durability. Excellent replacement for stock original equipment, high performance street, drag race and oval track. Includes gasket and new oil pan bolts.

Product Features:

Steel core provides rigidity, durability and prevents gasket push out
Molded rubber coating seals minor irregularities in pan surface
One piece design is easier to install and even less prone to leak
Direct replacement suitable for all uses – street, racing, heavy duty
Include both gasket and new oil pan bolts
No Cork Particles
Easy Removal For Disassembly

from

$107.99

Product Features:

Highest Quality Head Bolts
Cold-Formed/Heat Treated
Ensures Molecular Integrity
Reduced Diameter Bolt Heads
Hardened/Parallel-Ground Washers Included
Rated At 170000 psi
Manufactured By ARP

from

$349.99

New Everbright(TM) Manifold coating now available on the most popular Weiand and Holley intakes uses proprietary vacuum metalizing technology combined with a protective clear powdercoat to provide long lasting, virtually maintenance free polished looks.

Product Features:

Low Rise/Dual Plane Design For Maximum Torque
Permanent Mold Casting Process
Lighter/Smoother/Better Looking/Consistent Casting
Dyno Proven To Make 25hp Over Competition
Fully CNC Machined For A Perfect Fit
Square Bore Carburetor Flange
Exhaust Crossover For Improved Street Drivability

from

$43.99

Super Intake Manifold Bolts

from

$427.99

These COMP Cams Ultra-Gold Aluminum Roller Rocker Arms with a 3/8″ stud diameter and 1.6 ratio are designed for Ford V8 289-302-351W applications. The new modern design features of these Ultra-Gold Rockers are proven to withstand extremely aggressive spring pressure and valve lift. Designed specifically for high performance street and race engines, the Ultra-Gold Aluminum Rocker Arms are precision CNC-machined to strict tolerances. Developed to meet the demands of professional engine builders, these rockers include features never before possible in an aluminum rocker arm.

Product Features:

CNC-machined, lightweight design removes weight and yields unrivaled quality and ratio accuracy
Designed for high performance street and race engines
Precision-sorted trunion bearings withstand elevated valve spring pressure and valve lift
Additional clearance, up to 1.650″ O.D. valve spring

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$358.99

Edelbrock #88433 Water Pump Ford 1970-78 302 & 1970-87 351w v8 black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cool

Product Features:

Standard Impeller Rotation
0.625 in. Pilot Shaft
0.750 in. Ball/Ball Bearing
5.70 in. Block To Hub Height
Black Finish

from

$100.99

Product Features:

Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$1035.99

50 state street legal aluminum cylinder head. Out-of-the-box bolt-on performance. Intake valves are used for stock pistons.

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
Intake Valves Are For Use w/Stock Pistons

from

$975.99

Product Features:

Complete Single For Hydraulic Flat Tappet
60cc Combustion Chamber Volume
170cc Intake/60cc Exhaust Runner Volume
1.9 in. Intake/1.6 in. Exhaust Valve Diameter
0.625 in. Deck Thickness

from

$21.79

Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:

6 3¿8″ diameter
6 3┐8″ diameter
289-302-351 cu. in.
Increased Performance
Set Valve Lash At Proper Time

from

$38.49

Mr. Gasket Harmonic Balancer Bolt for Ford V8 except 351C. Fits 221,260,289,302,351W small block Windsor engines, 332,352,360,390,406,410,427,428 FEs, and 429,460 385 series big blocks. 5/8-18 x 2 inch long heat treated black oxide coated Grade 8 alloy steel with a thick parallel ground washer to provide accurate, uniform torque.

Product Features:

Heat treated black oxide coated Grade 8 alloy steel
Thick parallel ground washer provides more accurate, uniform torque
Hex Prevents Socket Slippage
Accurate And Uniform Torque
Black Plated Finish

from

$34.99

Product Features:

Valve Cover Gasket

from

$30.19

Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Manufactured from high-density cork/rubber blend gasket material
Provides excellent sealing and durability
For OE replacement, high performance street, drag race and oval track use

from

$48.09

Precision die cast, these water necks or thermostat housings are first polished to a high luster, then chrome plated. Comes with gasket and Allen head mounting bolts. Fits 1979-1997 Ford 5.0/5.8L V8s.

Product Features:

Chrome Plated For Great Looks
Includes Gasket & Mounting Bolts

from

$38.49

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. Comes complete with front & rear manifold end seals. For original equipment replacement, high performance street, drag race and oval track.brbrFits all Ford 351M/400 – 4V or 4-Barrel heads.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Die-cut for an excellent fit
Can be trimmed if necessary for modified port applications
Complete with manifold end seals
For OE replacement, high performance street, drag race and oval track use

from

$39.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro performance intake manifold gaskets have been tested with virtually all aftermarket cylinder head and intake manifold combinations.
Performance intake manifold gaskets designed without a metal core, to allow engine builders to trim the gasket for exact fit on modified ports.
1970-82; w/2 Bbl. Cylinder heads
Printoseal elastomeric sealing beads to provide extra sealing strength around the intake port.
Not intended for use in emission controlled vehicles.

from

$522.99

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Product Features:

Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
Best with aftermarket converters and more rear gear.
Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.

from

$284.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$110.99

Our unique Multi-Layered steel head gasket embossment formation process optimizes the embossment radius, reduces stress points, enhances gasket conformability, and provides uniform clamp load distribution. This all results in superior surface contact between block and cylinder head. All head gasket layers/spacers go through an additional process to significantly reduce forming induced stress. Advantages are reduced brittleness in material, increased flexibility and deformation retention. This stabilizes the gasket, resulting in reduced cylinder bore distortion and improved combustion seal fro the extreme cylinder pressures found in high compression, supercharged and turbocharged applications. A proprietary polymer coating ensures the micro-seal of engine coolant and oil fluids.brbrA typical MLS head gasket requires a smoother (30Ra) surface finish than composite head gaskets. Mr. Gasket’s proprietary polymer coating will seal a surface finish twice as rough (60Ra) as a typical MLS head gasket. For high performance street, drag race and oval track use.

Product Features:

Gasket bore – 4.030 inch: Compressed thickness – .040 inch
Manufactured from 3-layer premium grade stainless steel and state of the art laser cutting
Optimized sealing embossments seals extreme cylinder pressure
Provides excellent stability and reduces cylinder bore distortion.
Proprietary polymer coating ensures the micro seal of engine coolant and oil fluids.
Ideal for supercharged, turbocharged, nitrous oxide and extreme compression ratio engines
For high-performance street, drag race and oval track use

from

$51.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$58.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

1995 Ford F-150 Pickup Performance Engines

More 1995 Ford F-150 Pickup Performance Engines

Essential 1995 Ford F-150 Pickup Performance Engines

Competition Cams – Xtreme Energy 240/246 Hydraulic Flat Cam and Lifter Kit (Part No.CL35-250-4)

Edelbrock – Throttle Body, 90mm, Pro-Flo XT, Ford-Style, Black Powder Coated Finish (Part No.38183)

Edelbrock – Sure Seat Valve Springs for Ford 351W V8 (Part No.5982)

Edelbrock – TIMING CHAIN (Part No.7844)

FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2941)

Edelbrock – Pushrod Set for Ford 351M/400 (Part No.9633)

Mr. Gasket – Ultra Seal: Oil Pan Gasket (Part No.6683)

Edelbrock – 289-302 Ford Head Bolt Kit (Part No.8552)

Weiand – Action +Plus; Intake Manifold (Part No.8010)

Mr. Gasket – Super Intake Manifold Bolts (Part No.6082)

Competition Cams – Ultra-Gold ARC Rocker Set w/ 1.6 Ratio for Ford 289-351W w/ 3/8" Stud (Part No.19043-16)

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

Edelbrock – Water Pump for Small-Block Ford 351W in Black Finish (Part No.88433)

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9724)

Edelbrock – Performer Small-Block Ford 1.90" Cylinder Head Hydraulic Flat Tappet (Part No.60329)

Edelbrock – Performer Small-Block Ford 5.0L/ 5.8L Cylinder Head 1.90 Polished (Part No.603719)

Mr. Gasket – Precision Timing Tape (Part No.1594)

Mr. Gasket – Ultra Seal: Harmonic Balancer Bolt/Washer Kit (Part No.7847)

Edelbrock – Valve Cover Gasket Set for Ford (Part No.7569)

Mr. Gasket – Valve Cover Gasket Set (Part No.276)

Mr. Gasket – Water Neck (Part No.9713)

Mr. Gasket – Intake Gasket (Part No.222)

FEL-PRO Performance – Lower Intake Manifold Gasket Set: 7 Piece Set (Part No.1240)

Competition Cams – Mutha’ Thumpr 235/249 Hydraulic Roller Cam (Part No.32-601-8)

Competition Cams – Xtreme Energy 240/246 Hydraulic Flat Cam (Part No.35-250-4)

Mr. Gasket – Mls Head Gasket (Part No.3175G)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1011-1)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1013)

Popular 1995 Ford F-150 Pickup Performance Engines Categories

1995 Ford F-150 Pickup Performance Engines

Performance Engines Brands To Make Your 1995 Ford F-150 Pickup Last

Popular FEL-PRO Performance Performance Engines

Top 1995 Ford F-150 Pickup Performance Engines from Mr. Gasket

FAQs for 1995 Ford F-150 Pickup Performance Engines

What are the most purchased Performance Engines for the 1995 Ford F-150 Pickup?

What are the top-rated 1995 Ford F-150 Pickup Performance Engines?

More Popular Parts for All Makes