1993 Chevrolet S10 Blazer Performance and Racing Products

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
• Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
• Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
• Slotted bolt holes allow for easier header installation.
• Not intended for use in emission controlled vehicles.

The K&N 57-3028 FIPK air intake system replaces the restrictive factory air filter and air intake assembly. K&N intakes are designed to dramatically reduce intake restriction allowing your engine to inhale a larger amount of air than the factory air filter assembly. More air means more usable power and acceleration throughout the engine’s RPM range. The 57-3028 air intake comes with a large, round K&N embossed chrome-topped high-flow air filter that funnels air directly into the engine’s throttle body for a guaranteed power gain. The oversized air filter can be used for up to 100,000 miles before servicing is needed depending on driving conditions. This air intake is relatively easy to install usually in 90 minutes or less. The tools needed are a screwdriver and a 10 millimeter wrench.

Product Features:

• GUARANTEED INCREASE IN HORSEPOWER: Dyno-tested with up to 50% more airflow than restrictive factory box air filter and intake tube
• BETTER TOWING: Improves acceleration and uphill performance when towing by improving throttle response.
• IMPROVED ENGINE SOUND: Hear the power under the hood.
• WORLD CLASS PROTECTION: Pushing the limits of engine protection by protecting your engine from harmful contaminants
• EASY MAINTENANCE: No filter cleaning required for up to 100,000 miles
• EASY TO INSTALL: Bolt-on power in less than an hour with basic hand tools. K&N air intake systems are one of the easiest ways to guarantee an increase in horsepower.
• DYNO TESTED: Dyno-tested for a guaranteed increase in horsepower and acceleration with no ECU tune required
• HIGH QUALITY: Made in America.

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

• Easy to Install
• Superior Material
• Saves Your Tie Rods
• Lasts Longer
• Looks Great

Product Features:

• Fuel Economy From The Engine
• Leak Test For Max Performance
• Mandrel-Formed Power Plenum
• Leakproof O-Ringed Port Seals
• Include All Mounting Hardware

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
• Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
• Not intended for use in emission controlled vehicles.

Product Features:

• For Idle to 5500 RPM Street-Driven Performance
• Excellent Throttle Response and Mid-Range Power
• 50-State Street Legal if Correct Carburetor Used
• Ideal for Light-Duty Pickups and Passenger Cars
• Unique Design Allows Use Of 2 bbl Or 4 bbl Top

Use with a short water pump to convert to a long water pump.

Product Features:

• Water Pump Spacer Kit

Hypertech Power Chips are engineered for stock 1981-1995 GM vehicles. The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. Street Runner Power Chips are designed for daily street driving or competition in unmodified vehicles using a stock thermostat.

Product Features:

• Designed For Daily Street Driving
• For Unmodified Vehicles w/Stock Thermostat
• Controls Engines Air/Fuel Ratio
• Controls Spark Advance For Max Power
• Potential Gas Mileage Improvements
• No Wiring Or Soldering Required
• Installs In Less Than 30 Minutes

The Original Pro Stick shifter delivers rock-solid performance, mixed with clean design cues and compact size. This is why you see so many Pro Stick shifters at the race track. We start off with a heavy duty steel base with a hardened steel gate plate, a reverse lockout feature that only requires one hand to operate, and complies with NHRA/IHRA safety rules. Then add the billet aluminum shift handle with classic white shift knob, lightweight aluminum trigger and finish it off with a brushed aluminum cover with quick release pins, and you end up with one good looking bullet-proof race shifter. Optional Forward and Reverse shift pattern gate plates are available for most popular 2, 3 and 4-speed transmissions. This model Pro Stick comes out of the box ready for action for most popular 3-speed transmissions, includes a 5-foot Super Duty shift cable, brackets, levers, hardware and detailed instructions for an easy installation. Be sure to check out all the optional Magnum Grip side grip plates including the one and two button 12-volt momentary switches or any of the other accessories we offer for the Pro Stick in the Shifter Accessories section. Notes: AOD requires installation kit #40496, AODE & 4R70W requires installation kit #40504, E40D & 4R100 requires installation kit #40505, 2004R & 700R4 require gate plate #80712, 4L60E – 4L85E equipped with PRNDL switch requires cable bracket kit #70499 and gate plate #80712. Overall Dimensions – 8.25L x 2.92W x 9.25H

Product Features:

• All One-Handed
• Reverse Lockout Meets NHRA And IHRA Requirements
• Mount Directly To Floor/Chassis/Or w/Quick Release
• Ultimate For Powerglide Applications
• Lightweight Brushed Alum. Cover
• Cover Removed Quickly and Easily
• Includes 5 Ft. Super Duty Race Cable
• Quick Change Plate Design

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
• Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
• Raises combustion sealing force to roughly three times that of standard head gaskets.
• Steel wire rings for the greatest combustion seal strength.
• Not intended for use in emission controlled vehicles.

Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.

Product Features:

• Allows Sway Bar System to Work At 100% Efficiency
• Zerk Type Fittings
• Allows for Periodic Greasing
• Lasts Much Longer Than OEM Rubber Bushings
• Handling Characteristics Improve Dramatically

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

• Maintains Better Alignment While Driving
• Full Floating and Non Binding
• Fits Into the Remaining Stock Control Arms

Designed to reduce wheel shimmy and end vibration caused by larger tires, the Rancho® steering stabilizer kit cuts down on steering arm fatigue to improve handling. The kit includes one Rancho RS5000® steering stabilizer and installation brackets.

Product Features:

• COMPATIBILITY — Designed for a variety of Chevrolet® and GMC® trucks and SUVs
• IMPROVED HANDLING AND PERFORMANCE — Reduces wheel shimmy, bump steer and vibration which helps minimize on- or off-road driver fatigue
• ACCOMMODATES LARGER TIRES — Engineered for vehicles with oversized wheels and tires.
• ENGINEERED TO LAST — Features protective boot to shield shock rod and oil seal and 0.25-in. high-strength, low-alloy steel bracket construction for long life
• EASY TO INSTALL — Includes one Rancho RS5000® steering stabilizer and brackets that bolt directly to factory steering linkage with included mounting hardware, no modifications needed
• RESISTS CORROSION — Durable black powder-coated and/or zinc-plated brackets resist rust and corrosion
• PRECISION DESIGN — Brackets are CNC cut and bent to exact specifications for a perfect fit

Adds a dramatic amount of performance and durability to any vehicle, cars, trucks and SUVs. Helps the vehicle be in control – when maneuvering through turns, during standing start accelerations, braking, even over bumps and berms. Made of Energy’s Hyper-Flex performance polyurethane which lasts 5 -10 times longer than conventional rubber components.

Product Features:

• Made of Superior Hyper-Flex+ Material
• Adds Dramatic Amount of Performance/Durability
• Helps Vehicle Be in Control
• Allows the Suspension to Function Properly

Flowmaster’s Super 44 muffler uses the same Delta Flow technology found in our larger Super 40 mufflers. The Super 44 delivers a rich powerful tone and are the most aggressive, highest performing street muffler we’ve ever built in a four inch case. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

• Maintains Better Alignment While Driving
• Full Floating and Non Binding
• Fits Into the Remaining Stock Control Arms

Product Features:

• Solid Bushing Chain Resists Stretching
• For Use with Stock or Edelbrock Camshafts
• Stressproof Steel Crank Gears
• 3 Keyway Setting Points To Ensure Accurate Timing
• True Bearing Surface Rolls with the Sprockets
• For OEM Hydraulic Roller Lifter Cams Only

Hypertech Power Chips are engineered for stock 1981-1995 GM vehicles. The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. Street Runner Power Chips are designed for daily street driving or competition in unmodified vehicles using a stock thermostat.

Product Features:

• Designed For Daily Street Driving
• For Unmodified Vehicles w/Stock Thermostat
• Controls Engines Air/Fuel Ratio
• Controls Spark Advance For Max Power
• Potential Gas Mileage Improvements
• No Wiring Or Soldering Required
• Installs In Less Than 30 Minutes

The cap and rotor of any ignition system must be considered maintenance items. Just as you change the oil and filter of your car, you should always replace the cap and rotor as a set. To make things easy, we now offer these cap and rotor replacement kits.

Product Features:

• Designed w/performance in mind
• High quality; voltage insulating material
• Stainless Terminals
• High dielectric properties

Manufactured from high quality machine finished aluminum, Spectre’s Throttle Body Spacers are engineered to improve engine performance. By providing added volume to the intake manifold and directing air through a tapered internal constriction, this spacer utilizes the Venturi effect to increase the speed of air flowing into your intake manifold. Spectre has designed a number of kits to fit a wide range of specific applications. Each kit includes the necessary gaskets and hardware to bolt directly to the factory components, making installation quick and easy.

Product Features:

• Includes the necessary gaskets and hardware to bolt directly to the factory components
• Each kit is designed for the applications listed
• Manufactured from high quality machine finished aluminum
• Can be installed in less than an hour using common hand tools with no drilling or cutting required
• Simple to install

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

• Features 12-point Smaller-than-standard Bolt Head
• Thick Flat Washers Distribute Optimum Clamp Load
• Ideal Use Where Space Is Minimal On Race Manifolds
• Bolts And Washers Zinc Plated For Protection
• Zinc Plated For Protection

A true performance application component for cars, trucks, hot rods and racing/competition vehicles – yet designed to be also used for street vehicles. Soft-running enough to absorb vibrations for street use yet rugged for racing use. When required- a torque resistant safety interlock design is used that is comparable in strength to those too hard-running metal mounts. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal motor mounts. The popular early style mounts for General Motors vehicles are available in either zinc or chrome metal finishes. Made of Hyper-Flex performance polyurethane. Resistant to under vehicle fluids such as: oils, coolants, road contaminants, etc.

Product Features:

• Gains Both Performance and Longevity
• Will Handle Any and All Torque
• Out Lasts Rubber

The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, new turbine hub and dual pattern drive lugs on some GM Holeshots.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine

Product Features:

• GM 10BL 7.5 &7.625 R/P 3.23 MGP 10 3/8 X 18 LH THRED BLTS, PD=1.438

Spectre’s Valve Cover Hold Downs feature high quality steel construction with a triple chrome-plated finish. Manufactured for an optimum fit, this product’s hex heads include a decorative O-ring cap for a customizable appearance to suit your needs. Sold 4 per package, these studs are intended to fit standard height Chevy Center bolt valve covers.

Product Features:

• 4 bolts included in each package
• Allen head includes decorative O-ring cap
• Triple chrome-plated finish
• Fits standard height Chevy Center bolt valve covers

Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Compatible with late model GM computer controlled remote mount HEI systems. Direct bolt-in, plug-in replacement. Brass coil wire contact increases energy transfer and resists corrosion better than aluminum. Complete with new mounting hardware.

Product Features:

• 10-15% More Energy
• Direct Plug In Replacement Direct OE Fit
• Advanced Bobbin Technology
• Highly Specialized Silicone Magnetic Steel Cores
• Standard Motor Products SMP DR-37
• MSD 8226
• Resist Corrosion
• W/New Mounting Hardware

K&N performance High-Flow Air Filters are engineered to improve engine performance. Unlike disposable paper filters which must be frequently replaced, K&N Air Filters are washable, reusable, and engineered to last for the life of your vehicle or outdoor power small engine. Engineered to fit easily into your factory air box, installation can be completed in a matter of minutes! K&N develops and tests each product on the world┐s toughest race tracks, so we can bring the highest level of performance to your daily driving. Join the millions of customers who have saved money and improved vehicle performance by upgrading to K&N filtration.

Product Features:

• ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
• RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
• 4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
• CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (based on the average miles driven per year of 15,000 miles)
• ULTIMATE LONGEVITY: No-hassle lifetime warranty on stock replacement K&N air filters- limitations apply
• EASY INSTALLATION: K&N Air Filters are pre-treated and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
• ECO-FRIENDLY: Using a washable, reusable engine air filter helps reduce replacement air filter waste- a K&N air filter is designed to last longer than 10 or more disposable filters
• MADE IN USA: K&N Air Filters are proudly made in the USA for trusted quality & reliability

Starting on the inside, a 0.500 In. oversized steel shaft spins in a sealed ball bearing and sintered bushing for long endurance and accurate spark delivery throughout the entire RPM range. Mounted on top of the shaft is an easy-to-adjust chromoly mechanical advance assembly. Different advance springs and stop bushings are supplied so you can choose from 24 curves. A maintenance-free magnetic pick-up provides accurate trigger signals to your MSD Ignition control. A precision-manufactured reluctor that is connected to the shaft is responsible for triggering the pick-up. The distributor is topped off with a high quality black cap and race rotor.

Product Features:

• CNC machined billet aluminum housing and billet aluminum base
• Will not accept a vacuum advance canister
• Must Be Used w/An MSD Ignition Control
• O-ring seals can be installed for oil press. control (Mods only)
• Supplied w/Socket Style Distributor Cap And Rotor
• Special oil tract improves lubrication to the dist./cam gear
• Nylon pads ensure smooth operation of the advance weights
• Advance weight pins are staked and tig welded to the plate