1993 Chevrolet S10 Blazer Performance and Racing Products

Below you will find various in-demand Chevrolet Performance and Racing Products, components and accessories for your 1993 S10 Blazer. Advance Auto Parts has popular S10 Blazer parts like Performance Ignition Products, Performance Air Filters, Performance Exhaust Products and more. You’ll also find aftermarket and OEM Performance and Racing Products for other S10 Blazer model years including 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1994 and more. Select a category of 1993 Chevrolet S10 Blazer Performance and Racing Products below and start saving instantly.

Popular 1993 Chevrolet S10 Blazer Performance and Racing Products Categories

Performance Engine Coolant Thermostats

Performance Starters

Performance Intake Manifolds

Computer Chip Programmers

Performance Air Filters

Performance Coils

Performance Exhaust Mufflers

Performance Distributor Cap and Rotor Kits

Performance Computer Prom and Chips

Performance Exhaust Headers

Performance Shifters

Performance Throttle Body Spacers

Performance Body Mounts

Performance Engine and Transmission Mounts

Performance Engine Water Pumps

Performance Radiator Caps

Performance Differential Covers

Performance Engine Intake Manifold Gaskets

Performance Coil Spring Insulators

Performance Engine Valve Springs

Performance Exhaust Manifold Gaskets

Performance Posi Units and Components

Performance Oil Pans

Performance Leaf Spring Bushings

Performance Valve Cover Hardware

Performance Upper Performance Control Arm Bushings

Performance Ring and Pinions

Performance Ignition Parts

Performance Sway Bar Link Kits

Performance Lower Control Arm Bushings

Performance Sway Bar Bushings

Performance Engine Main Bearing Gasket Sets

Performance Brake Bleeders

Performance Tie Rod End Boots

Performance Transmission Shift Kits

Performance Engine Timing Cover Gasket Sets

Performance Torque Converters

Performance Transmission Rebuild Kits

Manual Transmission Main Shaft Race

Essential Performance and Racing Products for 1993 Chevrolet S10 Blazers

from

$154.99

The three chamber design utilizes Flowmaster’s patented Delta Flow technology along with an internal tuning chamber to reduce sound inside the vehicle. Provides the same performance and exterior tone characteristics as the two chamber, but with less interior resonance. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

from

$41.99

A true performance application component for cars, trucks, hot rods, racing/competition, yet popularly used for street vehicles when more horsepower is added. Soft running enough to absorb vibrations for street use yet rugged for racing use. Helps control torque on high performance vehicles. Maintains proper drive shaft angle to help prevent early wear and unexpected power train damage. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal transmission mounts. Resistant to under vehicle fluid oils, coolants and road contaminants. Made of Energy’s Hyper-Flex performance polyurethane and heavy duty hardware – for added durability.

Product Features:

Unique Safety Interlock Design
Impervious to Vehicle Oils and Chemicals
Strong Enough Too Handle High Performance

from

$48.09

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:

Indicates coolant temperature
Helps prevent coolant injuries
Fahrenheit and centigrade readings
Color-coded temperature ranges
Integrated coolant reclamation valve
Improves under-hood appearance
Chromed crown with a colored trim ring

from

$47.99

Spectre’s Differential Covers are made to OEM specifications and are triple chrome plated for a lasting shine. Designed to protect the intricate moving parts of the differential, Spectre’s covers add an extra layer of protection to the vehicle’s underside. Featuring a 10-bolt design and includes a gasket, this differential cover is designed to fit 1978 and up Chevy/GM intermediates, 1982 and up Chevy Camaro/Pontiac Firebird, 1993-2002 Chevy Camaro/Pontiac Firebird V6, 1982-2003 Chevy S10/S15/Envoy, 1985-1998 Chevy Astro/GMC Safari, and 1998-2003 Isuzu differentials. Includes 10 SAE standard chrome bolts for installation. You’ll need to supply your own bolts if your application requires metric bolts.

Product Features:

10 bolt design cover
Includes gasket
Triple chrome plated for a lasting shine
10 chrome 5/16 inch -18 x 3/4 inch differential cover bolts included

from

$709.99

Holeshot 2400 for GM 1998 to 2002 4L60E Camaro and Firebird with an LS1 engine Application: GM 1998 to 2002 4L60E Camaro and Firebird with LS1 A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benef

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$94.99

Manufactured from high quality machine finished aluminum, Spectre’s Throttle Body Spacers are engineered to improve engine performance. By providing added volume to the intake manifold and directing air through a tapered internal constriction, this spacer utilizes the Venturi effect to increase the speed of air flowing into your intake manifold. Spectre has designed a number of kits to fit a wide range of specific applications. Each kit includes the necessary gaskets and hardware to bolt directly to the factory components, making installation quick and easy.

Product Features:

Includes the necessary gaskets and hardware to bolt directly to the factory components
Each kit is designed for the applications listed
Manufactured from high quality machine finished aluminum
Can be installed in less than an hour using common hand tools with no drilling or cutting required
Simple to install

from

$444.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$242.99

Will replace distorted and worn-out original rubber mounts to maintain car body and truck cab to bed alignment. Original rubber mounts are so soft they often crack, distort, and crush so badly they often fall off and aluminum body mounts are too harsh for street use that they tend to break and cause other components to break. Energy’s specially formulated Hyper-Flex polyurethane cab and body mounts combine the best qualities of both: they’re soft enough for a smooth ride, yet rugged enough for the most demanding road or track. Most sets have a strong zinc plated steel ring molded into them – for added durability and when the application requires it.

Product Features:

Assures Longer Lasting Cab to Bed Alignment
Replace to Restore Ride Height
Gain Durability
Stronger Than Original Rubber Mounts

from

$32.59

Brake Bleeder Screws

from

$32.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro performance intake manifold gaskets have been tested with virtually all aftermarket cylinder head and intake manifold combinations.
No exhaust crossover openings or blocking shields
Embossed steel core laminate w/coating
Not intended for use in emission controlled vehicles.

from

$43.99

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$215.99

Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:

Twisted Snout Water Pump Design For Updated Style
Street Performance
Heavy Duty Shaft w/5/8 in. Pilot
Six-Blade Stamped Steel
Anti-Cavitation Impeller
100 Percent Leak Tested

from

$49.99

If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.

Product Features:

Improved output coil for electronic ignitions
Works w/Blaster Ignition Or MSD 5/6/7 Series
Ballast Resistor Required If Used w/Stock Points Ignition
Alkyd tower w/high dielectric properties lessens carbon tracking

from

$57.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$83.99

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$43.99

Made of superior Hyper-Flex material. Saves replacing again and again, lasting 3 to 10 times longer. Assemble to chassis the same way as OEM isolators and do not adversely change ride characteristics.

Product Features:

Made of Superior Hyper-Flex+ Material
Lasts from 3 to 10 Times Longer
Assemble to Chassis Same Way as OEM
Maintains Factory Ride Characteristics
Simple Way to Increase Vehicle Height

from

$27.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$37.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$73.99

The B&M Shift Improver Kit the easiest way to get the performance you’ve always wanted out of your automatic transmission, two modes to select from: Heavy Duty, or Street/Strip. It’s our least expensive and simplest to install kit.

Product Features:

Provides Crisp Shifts
On Any Stock Automatic Transmission
Eliminates Soft/Sluggish Shift
Eliminates Shift Overlap
Eliminate Clutch and Band Wear
Improves Transmission Life
Transmission Removal Not Required

from

$43.99

Fits Chevy small block 265-400 CID, Chevy big block 396-454 CID, & 90 degree Chevy V6. The Starter Motor Heat Shield is built with heat-resistant material sandwiched between two aluminum plates. The shield protects the starter from heat buildup from the exhaust system, especially important when using headers.

Product Features:

Designed to prevent starter overheat due to extreme exhaust temperature
Heat resistant material sandwiched between 2 aluminum plates
Protects Starter From High Temperatures
Made Of 2 Sheets Of Aluminum Heat Resistant Center
Natural Finish

from

$48.49

The cap and rotor of any ignition system must be considered maintenance items. Just as you change the oil and filter of your car, you should always replace the cap and rotor as a set. To make things easy, we now offer these cap and rotor replacement kits.

Product Features:

Designed w/performance in mind
High quality; voltage insulating material
Stainless Terminals
High dielectric properties

from

$339.99

The Hammer shifter may just be the most comfortable and versatile shifter available. The unique design of the shift handle easily fits all sizes of hands providing the appropriate wrist angle and feel when shifting. The multi-position lockout trigger is s

Product Features:

Ratchet Action Shifter
Cable Operated
Quick Installation
Accurate Shifting
Reverse Lockout Feature

from

$168.89

Hypertech ThermoMaster Power Chips are engineered for stock 1995-1981 GM vehicles (premium octane fuel required). The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. ThermoMaster Power Chips are designed for daily street driving or competition in unmodified vehicles using a 160 Deg. or 180 Deg. thermostat. Hypertech Power Chips(TM) are emissions certified 50-state legal (application specific).

Product Features:

Use w/Low-Temp 160-180 Deg. PowerStat Thermostat
Controls Engines Air/Fuel Ratio
Controls Spark Advance For Max Power
Potential Gas Mileage Improvements
No Wiring Or Soldering Required
Installs In Less Than 30 Minutes
Product might not be available in all states due to local laws.

from

$14.99

Spectre’s Valve Cover Hold Downs feature high quality steel construction with a triple chrome-plated finish. Manufactured for an optimum fit, this product’s hex heads include a decorative O-ring cap for a customizable appearance to suit your needs. Sold 4 per package, these studs are intended to fit standard height Chevy Center bolt valve covers.

Product Features:

4 bolts included in each package
Allen head includes decorative O-ring cap
Triple chrome-plated finish
Fits standard height Chevy Center bolt valve covers

from

$50.99

Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.

Product Features:

Allows Sway Bar System to Work At 100% Efficiency
Zerk Type Fittings
Allows for Periodic Greasing
Lasts Much Longer Than OEM Rubber Bushings
Handling Characteristics Improve Dramatically

from

$564.99

A B&M transmission in a box! Transform your automatic transmission into a full-tilt B&M performer! This is our ultimate transmission kit – it comes complete with full instructions on how to assemble your transmission to B&M specifications.

Product Features:

High Perf. Friction Materials
Complete Overhaul Gasket Set
Modification Components
Replacement Valves
Replacement Springs
Drain Plug Kit Included

from

$9.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Saves Your Tie Rods
Lasts Longer
Looks Great

from

$360.99

RngPnn

Upgrade your 1993 Chevrolet S10 Blazer with Top-Quality Performance and Racing Products

When it comes to maintaining or upgrading your 1993 Chevrolet S10 Blazer, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Chevrolet or enhancing its overall performance, Performance and Racing Products are key to keeping your S10 Blazer functioning at its best. At Advance Auto Parts, we offer a wide selection of 87 Performance and Racing Products for the 1993 Chevrolet S10 Blazer, designed to meet your needs without breaking the bank. From Performance Ignition Product replacements to Performance Air Filters upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1993 Chevrolet S10 Blazer at great prices. Our Performance and Racing Products inventory for this model ranges from just $7.69 to $709.99, with an average price of $186.82. Our 87 Performance and Racing Products in stock come from 19 trusted brands, so you’re sure to find the right part for your 1993 Chevrolet S10 Blazer without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1993 Chevrolet S10 Blazer, we stock popular OEM and aftermarket Performance and Racing Products from top names like Energy Suspension, Mr. Gasket, MSD Ignition, and more. Energy Suspension Performance and Racing Products start at just $9.99 and boast an impressive 4 stars average rating from customers. Mr. Gasket and MSD Ignition also bring quality to the table, with Performance and Racing Products available starting at $17.49, and at an average 4 stars rating. With 205 customer reviews and counting, our 1993 Chevrolet S10 Blazer Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1993 Chevrolet S10 Blazer is always ready to roll. We’re committed to providing you with everything you need to keep your S10 Blazer in top shape, all in one place. Start shopping confidently below for your 1993 Chevrolet S10 Blazer!

Best-Selling Performance Ignition Products for 1993 Chevrolet S10 Blazers

Enhance the driving experience in your Chevrolet with 4 quality Performance Ignition Product components, starting at $65.99.

show more show less

from

$85.29

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

Service Part
No Moving Parts To Wear Out
Self Contained Unit
Can Drive OEM
Can Drive High Performance Ignition Coils

from

$71.99

Top off your GM ignition system with these great new replacement coils. The GM coils have MSD performance in factory style housings. MSD designed these coils by combining our blaster coil experience with e-core coil efficiency. Each coil has a unique turns ratio plus there is lower primary resistance than the stock coil. This all amounts to a bolt-in replacement coil that produces more output voltage. The coils will work with stock ignition systems as well as MSD equipped cars and trucks. Installation tip: If you plan to install an MSD ignition with your GM dual connector coil, use PN 8876 harness for a direct plug-in installation.

Product Features:

Direct performance replacement for GM dual connector coil
100:1 Turns Ratio
Lower Primary Resistance Produces High Voltage Output
Works w/Stock Ignition As Well As MSD Ignitions

from

$65.99

These new coils mount directly in place of the factory coils and accept the factory connectors. Spark energy is increased thanks to improved materials and windings that were spec’d by MSD engineering.

Product Features:

Replacement Coil For GM Dual Connector Coil
Improved Turns Ratio
Lower Primary Resistance
Bolt-In replacement coil
Produce More Output Voltage
Smooth Idle

from

$186.99

Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).

Product Features:

Glass Filled Polyester Case
Longer Spark Duration
Increased Performance
No Energy Loss Due To Arcing
Includes Brass Contact Terminal

Most Popular 1993 Chevrolet S10 Blazer Performance Air Filters

Customize your Chevrolet with 1 Performance Air Filters products like Performance Air Filters, all priced under $79.99.

show more show less

from

$79.99

K&N performance High-Flow Air Filters are engineered to improve engine performance. Unlike disposable paper filters which must be frequently replaced, K&N Air Filters are washable, reusable, and engineered to last for the life of your vehicle. K&N air filters are backed by our famous 10-Year/Million Mile Limited Warranty, and they provide an environmentally friendly way to reduce landfill waste by avoiding disposable filters. Engineered to fit easily into your factory air box, installation can be completed in a matter of minutes! K&N develops and tests each product on the world┐s toughest race tracks, so we can bring the highest level of performance to your daily driving. Join the millions of customers who have saved money and improved vehicle performance by upgrading to K&N filtration.

Product Features:

ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (based on the average miles driven per year of 15,000 miles)
ULTIMATE LONGEVITY: No-hassle lifetime warranty on stock replacement K&N air filters- limitations apply
EASY INSTALLATION: K&N Air Filters are pre-treated and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
ECO-FRIENDLY: Using a washable, reusable engine air filter helps reduce replacement air filter waste- a K&N air filter is designed to last longer than 10 or more disposable filters
MADE IN USA: K&N Air Filters are proudly made in the USA for trusted quality & reliability

Top Picks for 1993 Chevrolet S10 Blazer Performance Exhaust Products

Upgrade Chevrolet S10 Blazers with top-quality Performance Exhaust Products parts, including 7 OEM and aftermarket selections for your 1993 model.

show more show less

from

$123.99

The Original 40 series muffler delivers an aggressive exterior and interior tone. If you’re looking for that original Flowmaster sound this is the muffler is for you. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.

from

$91.99

DynoMax Ultra Flo Welded performance stainless steel mufflers feature 100-percent welded construction for lifelong durability. The unrestricted, straight-through design dyno proven to flow up to 2,000 SCFM and support up to 2,000 horsepower. Each muffler uses our exclusive Continuous Roving Fiberglass (CRF) Technology to absorb unwanted interior resonance while maintaining a deep performance tone.

Product Features:

Stainless steel construction for lifelong protection
100% welded design for maximum durability
Straight through design ensures unrestricted exhaust flow and reduces back pressure
CRF Technology absorbs unwanted interior resonance while maintaining a deep performance tone
Dyno proven to flow up to 2,000 SCFM and support up to 2,000 horsepower.

from

$27.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$302.99

Product Features:

Fuel Economy From The Engine
Leak Test For Max Performance
Mandrel-Formed Power Plenum
Leakproof O-Ringed Port Seals
Include All Mounting Hardware

from

$175.99

The three chamber design utilizes Flowmaster’s patented Delta Flow technology along with an internal tuning chamber to reduce sound inside the vehicle. Provides the same performance and exterior tone characteristics as the two chamber, but with less interior resonance. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.

from

$156.99

DynoMax Ultra Flo SS Polished performance mufflers are constructed of stainless steel for lifelong durability and completely polished for show-quality shine. The unrestricted, straight-through design is dyno proven to flow up to 2,000 SCFM and support up to 1,900 horsepower. Each muffler uses our exclusive Continuous Roving Fiberglass (CRF) Technology to absorb unwanted interior resonance while maintaining a deep performance tone.

Product Features:

Stainless steel construction for lifelong protection
Polished finish for a show quality shine
Dyno proven to flow up to 2,000 SCFM and support up to 1,900 horsepower
Straight through design ensures unrestricted exhaust flow and reduces back pressure
CRF Technology absorbs unwanted interior resonance while maintaining a deep performance tone

from

$154.99

In-Demand Performance Engines for 1993 Chevrolet S10 Blazers

Select from 13 premium Performance Engines parts for your 1993 Chevrolet S10 Blazer, with prices ranging from $20.29 to $709.99.

show more show less

from

$94.99

Includes the necessary gaskets and hardware to bolt directly to the factory components
Each kit is designed for the applications listed
Manufactured from high quality machine finished aluminum
Can be installed in less than an hour using common hand tools with no drilling or cutting required
Simple to install

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$215.99

Twisted Snout Water Pump Design For Updated Style
Street Performance
Heavy Duty Shaft w/5/8 in. Pilot
Six-Blade Stamped Steel
Anti-Cavitation Impeller
100 Percent Leak Tested

from

$215.99

Twisted Snout Water Pump Design For Updated Style
Street Performance
Heavy Duty Shaft w/5/8 in. Pilot
Six-Blade Stamped Steel
Anti-Cavitation Impeller
100 Percent Leak Tested

from

$27.99

Edelbrock part #7209 Intake Gaskets for 1985-1995, Chevy V6 200-229-262 (3.8 and 4.3L) allow for optimum flow and performance. Any gasket can create a seal, but a good gasket can do it with less clamping force, and for a longer period of time. The new MP-

Product Features:

1.28″x2.10″
Stock Port Style
.060″ Thick
Multi Piece Configuration
Composite Material

from

$20.29

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Steel core gasket construction
Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
Not intended for use in emission controlled vehicles.

from

$37.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$709.99

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$609.99

HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) Application: HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine
New Turbine Hub
New Springs/Rollers In Stator

from

$544.99

The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, new turbine hub and dual pattern drive lugs on some GM Holeshots.

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$112.99

Use with a short water pump to convert to a long water pump.

Product Features:

Water Pump Spacer Kit

from

$43.99

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$27.49

These grade 5 hex head bolts are black coated plated for protection and appearance. Hardened flat washers provide uniform torque and prevent galling on aluminum manifolds.

Product Features:

Assures Accurate Torque App
Prevents Galling Manifold
Grade 5 Material
Black Oxide Coasted

Most Sold 1993 Chevrolet S10 Blazer Performance Distributors

Explore our best-selling Chevrolet parts for the 1993 S10 Blazer among 1 OEM and aftermarket options starting from $48.49.

show more show less

from

$48.49

Designed w/performance in mind
High quality; voltage insulating material
Stainless Terminals
High dielectric properties

Top-Rated Performance and Racing Products Brands For Your 1993 Chevrolet S10 Blazer

Shop for the best-rated brands offering Performance and Racing Products and other products for your 1993 Chevrolet S10 Blazers. Below you’ll find some of our best rated Performance and Racing Products from Energy Suspension, Mr. Gasket, and MSD Ignition, and more. Performance and Racing Products from these brands that fit a 1993 S10 Blazer start at just $9.99 and are rated as high as 4 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.

Popular Energy Suspension 1993 Chevrolet S10 Blazer Performance and Racing Products

When it comes to maintaining or upgrading your 1993 Chevrolet S10 Blazer, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. Energy Suspension ticks all of those boxes. We offer a wide selection of Energy Suspension Performance and Racing Products, specifically designed for the 1993 Chevrolet S10 Blazer. With over 20 Energy Suspension brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $9.99, with an average price of just $78.54. Plus, with over 20 customer reviews and an average rating of 4 stars, you can trust that our Energy Suspension Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from
$63.99

This product is not rated

Motor Mount

“”

from
$70.99

This product is not rated

Leaf Spring Bushing Set

“”

from
$116.99

This product is not rated

Control Arm Bushing Set

“”

Popular Mr. Gasket 1993 Chevrolet S10 Blazer Performance and Racing Products

Mr. Gasket auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1993 Chevrolet S10 Blazer owner should feel confident when installing genuine Mr. Gasket parts in their vehicle. To ensure the best fit and performance for your 1993 S10 Blazer, Advance Auto Parts carries a full inventory of 5 Mr. Gasket Performance and Racing Products. Plus you will be keeping your Chevrolet in peak condition while saving money because prices on these Mr. Gasket Performance and Racing Products range from $17.49 to $48.09, plus, with more than 23 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.

from
$27.49

This product is not rated

Super Intake Manifold Bolts

“”

from
$17.49

This product is not rated

Oil Pan Bolt Kit

“”

from
$48.09

This product is not rated

Thermocap Radiator Cap

“”

FAQs for 1993 Chevrolet S10 Blazer Performance and Racing Products

Which Performance and Racing Products are best-sellers for 1993 Chevrolet S10 Blazers?

Out of 87 Performance and Racing Products that fit 1993 Chevrolet S10 Blazers, the following parts are the top sellers:

High Performance Transmission Mount for Street & Racing Vehicles (16360003) – $41.99
High Performance 180 Degree Thermostat for Increased Flow (17360033) – $26.99
Coil; GM External HEI Coil; High Performance (17350179) – $71.99

What’s the price range for 1993 Chevrolet S10 Blazer Performance and Racing Products?

Performance and Racing Product prices for the 1993 Chevrolet S10 Blazer start at $7.69 and go up to $709.99 for the most premium parts.

What’s the average price of a Performance and Racing Product for a 1993 Chevrolet S10 Blazer?

The average price for Performance and Racing Products for the 1993 Chevrolet S10 Blazer is $186.82. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Performance and Racing Products for other Chevrolet S10 Blazer model years?

Yes, we currently carry Performance and Racing Products for 11 model years of Chevrolet S10 Blazers between 1983 and 1994. Performance and Racing Products are bought most frequently for the following model years: 1994, 1992, 1991, 1990, 1989, 1988, 1987, 1986, and 1985.

What are the cheapest Performance and Racing Products for my 1993 Chevrolet S10 Blazer?

The cheapest 1993 Chevrolet S10 Blazer Performance and Racing Products we carry in stock are:

CUP (50206003) – $7.69
Tie Rod Dust Boot (17360821) – $9.99
Valve Cover (22905495) – $14.99
Oil Pan Bolt Kit (17360377) – $17.49
Engine Timing Cover Gasket (21021905) – $20.29

What are the top-rated Performance and Racing Products that fit the 1993 Chevrolet S10 Blazer?

Out of 205 reviews by customers, our 1993 Chevrolet S10 Blazer Performance and Racing Products have an average customer rating of . These are some of the highest-rated Performance and Racing Product types for the 1993 Chevrolet S10 Blazer and their top-rated products:

Performance Air Filters
- Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration (6274005) – $79.99
Performance Transmissions
- Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration (6274005) – $79.99

What types of Performance and Racing Products do you sell for my 1993 Chevrolet S10 Blazer?

As of 2/5/25, these are some of the most in-demand types of Performance and Racing Products for a 1993 Chevrolet S10 Blazer:

Can I get help with 1993 Chevrolet S10 Blazer Performance and Racing Product orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Chevrolet Performance and Racing Products and more.

What is your return policy for Chevrolet S10 Blazer Performance and Racing Products?

Advance Auto Parts keeps returns simple. For new Chevrolet S10 Blazer Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1993 Chevrolet S10 Blazer Performance and Racing Products

Flowmaster Inc. – 50 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Moderate Sound (Part No.942451)

Energy Suspension – High Performance Transmission Mount for Street & Racing Vehicles (Part No.3.1108G)

Mr. Gasket – Thermocap Radiator Cap (Part No.2476BK)

Spectre – GM Differential Cover Camaro/S-10 (Part No.6074)

B & M – Holeshot 2400 (Part No.70441)

Spectre – Throttle Body Injection Spacer (Part No.11252)

Powertrax – Lock Right Locker (Part No.1931-LR)

Energy Suspension – Body Cab Mount Set (Part No.3.4132G)

Earls Performance Product – Brake Bleeder Screws (Part No.280022ERL)

FEL-PRO Performance – Lower Intake Manifold Gasket Set: 2 Piece Set (Part No.1270)

Edelbrock – Sure Seat Valve Springs for Chevy 4.3L 90 Deg V6 200, 229, 262 (Part No.5813)

Weiand – Action Plus Water Pumps (Part No.9240P)

MSD Ignition – Blaster 2 Coil: High Performance Ignition Upgrade (Part No.8202)

Energy Suspension – Control Arm Bushing Set (Part No.3.3170R)

Energy Suspension – Control Arm Bushing Set (Part No.3.3119R)

Energy Suspension – Coil Spring Isolator Set (Part No.9.6102R)

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1402)

FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2919)

B & M – Shift Improver Kit For 93-02 4L60E (Part No.70360)

Mr. Gasket – Starter Motor Heat Shield (Part No.3678)

MSD Ignition – Distributor Cap and Rotor; GM 4.3L; External Coil (Part No.8430)

B & M – Automatic Shifter, Hammer Shifter, Universal (Part No.80885)

Hypertech – ThermoMaster Power Chip (Part No.122012)

Spectre – Valve Cover (Part No.5280)

Energy Suspension – Sway Bar Bushing Set (Part No.3.5207R)

B & M – Transkit For 87-93 TH700R4 Transmission (Part No.70233)

Energy Suspension – Tie Rod Dust Boot (Part No.9.13101R)

Richmond Gear – RngPnn (Part No.49-0007-1)

Mallory – Unilite Ignition Module (Part No.605)

MSD Ignition – Coil; GM External HEI Coil; High Performance (Part No.8226)

MSD Ignition – Direct-Fit Replacement Coil with Improved Energy Output and Easy Installation (Part No.5526)

Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)

K&N – Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration (Part No.33-2042)

Flowmaster Inc. – 40 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Aggressive Sound (Part No.8042441)

Dynomax – Ultra Flo Muffler: Universal Fit Stainless Steel, 14" L, 2.5" In, 2.5" Out, Oval (Part No.17222)

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1402)

Flowtech – Standard Header (Part No.11502FLT)

Flowmaster Inc. – 50 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Moderate Sound (Part No.842451)

Dynomax – Ultra Flo Muffler: Universal Fit Stainless Steel, 14" L, 2.5" In, 2.5" Out, Oval (Part No.17283)

Flowmaster Inc. – 50 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Moderate Sound (Part No.942451)

Spectre – Throttle Body Injection Spacer (Part No.11252)

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

Weiand – Action Plus Water Pumps (Part No.9240P)

Weiand – Action Plus Water Pumps (Part No.9208P)

Edelbrock – Intake Manifold Gasket for 1985-1995, Chevy V6 200-229-262 (Part No.7209)

FEL-PRO Performance – Engine Timing Cover Gasket (Part No.2335)

FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2919)

B & M – Holeshot 2400 (Part No.70441)

B & M – Holeshot 2400 (Part No.70419)

B & M – Torque Converter, Holeshot 2000 (Part No.70417)

Weiand – Team G; Water Pump Spacer Kit (Part No.8207)

Edelbrock – Sure Seat Valve Springs for Chevy 4.3L 90 Deg V6 200, 229, 262 (Part No.5813)

Mr. Gasket – Super Intake Manifold Bolts (Part No.6080)

MSD Ignition – Distributor Cap and Rotor; GM 4.3L; External Coil (Part No.8430)