1990 GMC C1500 Drivetrains
Find Your Specific 1990 GMC C1500 Drivetrains
Below you will find various in-demand GMC Drivetrains, components and accessories for your 1990 C1500. Advance Auto Parts has popular C1500 parts like Drive Shafts and Axles, Transfer Cases, Differentials and more. You’ll also find aftermarket and OEM Drivetrains for other C1500 model years including
1991,
1992,
1993,
1994,
1995,
1996,
1997,
1998,
1999 and more. Select a category of 1990 GMC C1500 Drivetrains below and start saving instantly.
Popular 1990 GMC C1500 Drivetrains Categories
Essential Drivetrains for 1990 GMC C1500s
Yukon Gear – Pinion Install Kit For GM 12 Bolt Truck Differential (Part No.13057)
from
$232.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.
Product Features:
See More
Product Features:
- Fits GM 12 bolt truck
- Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.
Yukon Gear – Axle Seal, For 1559 Or 6408 Bearing (Part No.30201)
from
$7.99
Axle seal, for 1559 OR 6408 bearing, NOT COARSE spline 12T.Yukon Mighty seal.
Product Features:
See More
Product Features:
- Rear axle seal
- 2.530″ O.D.
FAG US – Repair Sleeve (Part No.SR3506)
from
$53.99
The FAG repair sleeve is a precision element that provides additional sealing for damaged shafts. Made of heat-treated stainless steel, the FAG repair sleeve signifcantly increases the life of the shaft and prevents premature wear. Since no shaft removal or machining is required during the repair, the repair sleeve is a cost effective repair solution to protect damaged surfaces.
Product Features:
See More
Product Features:
- High-precision and High-quality components used in all KITs
- Coverage of classic and new high-tech solutions for the best system coverage
Yukon Gear – The Carrier Bearing Puller (Part No.56072)
from
$883.99
The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.
Product Features:
See More
Product Features:
- Carrier bearing puller
- Works with an impact gun to safely and easliy remove carrrier bearings
National – Shaft Repair Sleeve (Part No.99125)
from
$30.49
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Designed to repair damaged, grooved or worn shafts
- Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
- Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
- Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
- Easy to install with removable flange and installation tool
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6053)
from
$38.99
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CHEV 60-02; DODGE 64-66; FORD 75-15; GMC 60-02;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1960-2015
- Weight approx: 3 Lbs
- BEARING ID / BORE: 1.5750 INCH / 40 MM
- CENTERLINE: 2.28 INCH / 58 MM
- MOUNT WIDTH: 6.62 INCH / 168 MM
- NO STUDS
Yukon Gear – Dura Grip Positraction For GM 8.5" & 8.6" With 30 Spline Axles (Part No.26016)
from
$929.99
The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects. This unit has larger bearing journals for added strength & uses heavy-duty carrier bearings & races.
Product Features:
See More
Product Features:
- Fits GM 8.5″ and 8.6″ with 30 spline axles
- 2.73 ratio and up only
- 4-spring, clutch style positraction
- Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
- Fully rebuildable
- Assembled in the USA
Yukon Gear – 8.2" & 8.5" Rear Cover Gasket (Part No.23020)
from
$10.99
8.2″ & 8.5″ rear cover gasket.
Product Features:
See More
Product Features:
- Cover gasket
- Fits GM 8.2″, 8.5″ and 8.6″
Driveworks – Wheel Bearing: Direct Fit, 1 Piece (Part No.S-5707)
from
$15.99
Driveworks wheel bearings are a direct replacement for original parts at a much more affordable cost. Each wheel bearing is engineered to meet or exceed OE specifications, and goes through intensive quality control inspections to ensure proper fitment. Manufactured using high-precision machinery and advanced heat treatment processes, these bearings are designed for maximum durability and extended periods of use under any driving condition. Specific to certain applications, Driveworks bearings have multi-lip seals built into the bearing for increased protection against invasive contaminants and premature wear.
Product Features:
See More
Product Features:
- Depending on the application, specified Driveworks wheel bearings have integrated encoder rings that automatically sync with the vehicle’s anti-lock braking system (ABS) upon successful installation
- Engineered, manufactured, and tested to meet or exceed OE specifications
- Integrated seal design improves contamination resistance for a longer bearing life
- High performance grease is used to lubricate the inner raceway to ensure smooth operation, higher operating temperatures, and minimal noise
- Manufactured from high quality steel to maximize durability under even the harshest driving conditions
- Brand may vary by location
Yukon Gear – Standard Open Pinion Gear Thrust Washer For GM 12P And 12T (Part No.33381)
from
$11.99
Standard Open pinion gear thrust washer for GM 12P and 12T.
Product Features:
See More
Product Features:
- Pinion gear thust washer for GM 12 bolt passenger car and truck
- Fits standard open differentials only
Spartan – Drive Axle Assembly; GM C1500 88-99 RWD GU6 (Part No.RAX1510C)
from
$1608.99
Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.
Product Features:
See More
Product Features:
- Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
- Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
- Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
- Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio
Dorman – Spindle Nut 3/4 In.-20 Hex 1-1/16 In. (sold by each) (Part No.615-065)
from
$4.99
This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Felpro – Axle Housing Cover Gasket: Irregular Shaped 14 Bolt Hole Gasket (Part No.RDS 55387)
from
$8.99
Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Validated for fit, form and function
- Unsurpassed quality you can trust
Dorman – Differential Pinion Yoke Assembly (Part No.697-531)
from
$323.99
Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this differential end yoke matches the fit and construction of the original yoke
- Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
- Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
- Validated fit – this differential end yoke has been tested to confirm accurate fit
Yukon Gear – Super Carrier Shim Kit For GM 9.5" (Part No.55003)
from
$29.99
9.5″ GM differential carrier Supershim kit.
Product Features:
See More
Product Features:
- Super carrier shim kit for GM 9.5″
- Interlocking design makes installation much easier
National – Bearing Race (Part No.LM501314)
from
$9.29
Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION – Crowned raceways for even load distribution
- OE-STYLE DESIGN – Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Dorman – Drive Shaft: Greaseable (Part No.976-871)
from
$715.99
Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.
Product Features:
See More
Product Features:
- Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
- 100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
- Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
- Serviceable construction – non-staked universal joints are designed for future serviceability
Yukon Gear – Differential Cover B (Part No.33572)
from
$7.99
Differential Cover B
Pro-King – Differential Cross Shaft (Part No.742G930)
from
$2.99
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.
Product Features:
See More
Product Features:
- All products are designed to meet or exceed OE quality, form, fit and funtion.
Yukon Gear – Yoke For GM 8.5" With A 1310 U/Joint Size (Part No.41086)
from
$449.99
Yukon yoke for GM 8.5″ with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits GM 8.5″
- 30 spline
- 1310 u-joint size
- Outside snap ring design
- 3.219″ snap ring span
- 1.062″ cap diameter
- Strap style
National – Bearing (Part No.M88048)
from
$13.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION — Crowned raceways and rollers for even load distribution
- OE-STYLE DESIGN — Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Dorman – Differential Yoke including Seal and Pinion Nut (Part No.697-500)
from
$139.99
Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this differential end yoke matches the fit and construction of the original yoke
- Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
- Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
- Validated fit – this differential end yoke has been tested to confirm accurate fit
Driveworks – Taper Bearing Cone (Part No.S-M-88048)
from
$11.29
Value-priced bearing meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
Yukon Gear – Standard Open Spider Gear Kit For 33 Spline GM 9.25" IFS And GM 9.5" Axles (Part No.16060)
from
$317.99
Yukon standard open spider gear kit for 9.5″ GM rear and ’06 and earlier GM 9.25″ IFS with 33 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Spider gear kit
- Fits GM 9.5″ open differential
- Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
Pro-King – Differential Cross Shaft (Part No.742G673)
from
$28.49
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.
Product Features:
See More
Product Features:
- All products are designed to meet or exceed OE quality, form, fit and funtion.
National – Drive Shaft Center Support Bearing (Part No.HB-88107-A)
from
$44.99
Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.
Product Features:
See More
Product Features:
- BUILT TO LAST – Advanced heat treatment process for strength
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
- RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Yukon Gear – 9.5" GM C/Clip (Part No.33081)
Yukon Gear – C/Clip (Part No.33083)
from
$8.99
C/Clip for Chrysler 8.25″, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 8.2″, 8.5″ & 8.6″.
Product Features:
See More
Product Features:
- c-clip for Chrysler 8.25″, Ford 8.8″, GM 12 bolt car and truck and GM 8.2″, 8.5″ and 8.6″
- .150″ thick
Upgrade your 1990 GMC C1500 with Top-Quality Drivetrains
When it comes to maintaining or upgrading your 1990 GMC C1500, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your GMC or enhancing its overall performance, Drivetrains are key to keeping your C1500 functioning at its best. At Advance Auto Parts, we offer a wide selection of 395 Drivetrains for the 1990 GMC C1500, designed to meet your needs without breaking the bank.
From
Drive Shafts and Axle
replacements to
Transfer Cases
upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.
Affordable Prices and Wide Selection
Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 1990 GMC C1500 at great prices.
Our Drivetrains inventory for this model
ranges from just $2.59 to $2,304.99, with
an average price of $270.81.
Our 395 Drivetrains in stock come from 24 trusted brands, so you’re sure to find the right part for your 1990 GMC C1500 without overspending.
Top Brands and High Customer Satisfaction
Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1990 GMC C1500, we stock popular OEM and aftermarket Drivetrains from top names
like National, DriveWorks, Motive Gear, and more.
National Drivetrains
start at just $7.99 and boast an impressive 4.3 stars average rating from customers.
DriveWorks and Motive Gear also bring quality to the table, with Drivetrains available starting at $4.99, and at an average 4.3 stars rating.
With 11,676 customer reviews and counting, our 1990 GMC C1500 Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.
Explore Related Parts and More
While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants
and more to make sure your 1990 GMC C1500 is always ready to roll. We’re committed to providing you with everything you need to keep your C1500 in top shape, all in one place.
Start shopping confidently below for your 1990 GMC C1500!
Best-Selling Drive Shafts and Axles for 1990 GMC C1500s
Enhance the driving experience in your GMC with 49 quality Drive Shafts and Axle components, starting at $5.29.
National – Bearing (Part No.M88048)
from
$13.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION — Crowned raceways and rollers for even load distribution
- OE-STYLE DESIGN — Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6038)
from
$40.99
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHEV 60-02; DODGE 57-02; FORD 55-07; GMC 63-02; INTL 57-02; KW 81-18; MACK 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1955-2018
- Weight approx: 4 Lbs
- BEARING ID / BORE: 1.5750 INCH / 40 MM
- CENTERLINE: 2.48 INCH / 63 MM
- MOUNT WIDTH: 6.62 INCH / 168 MM
- STYLE: ROUND FRAME
- NOT PICTURED: TWO DUST SHIELDS
Dorman – Help – Auto Transmission Case Vent (Part No.14689)
from
$7.49
This transfer case vent is designed to match the fit and function of the original vent on specified vehicles, and is engineered for durability and reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this transfer case vent is designed to match the fit and function of the original vent on specified vehicles
- Restores functionality – reliable replacement for an original vent that has failed due to blockage or fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
National – Drive Shaft Center Support Bearing (Part No.HB-206-FF)
from
$46.99
Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.
Product Features:
See More
Product Features:
- BUILT TO LAST – Advanced heat treatment process for strength
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
- RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Driveworks – Universal Joint (Part No.DW-331BL)
from
$15.99
Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).
Product Features:
See More
Product Features:
- The cross is hot forged for the higher torque and horsepower
- The bearing cups are made by cold forging, having higher strength and better rigidity
- Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
- Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
- Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
- Snap rings are held to strict tolerances to ensure proper cup position and retention
- Nitrile rubber seals to optimize grease retention and reduce contamination
National – Wheel Bearing (Part No.5707)
from
$22.99
Manufactured with premium-grade steel, National® cylindrical bearings are designed and engineered to meet OE specifications.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Controlled heat treating process for lasting performance and extended bearing life
- Industry leading coverage
- Professional technicians know they can depend on National
Dorman – Help – Axle Shaft Lock Assortment (Part No.81050)
from
$6.99
This drive axle shaft lock C-clip is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this drive axle shaft lock C-clip matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this clip is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Spicer – Universal Joint, Greaseable 1350 Series (Part No.5-178X)
from
$44.99
When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.
Product Features:
See More
Product Features:
- OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
- Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
- The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
- Zerk allows for lubricating at regular intervals to help extend the life of the part.
National – Drive Shaft Center Support Bearing (Part No.HB-88508-A)
from
$73.99
Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.
Product Features:
See More
Product Features:
- BUILT TO LAST – Advanced heat treatment process for strength
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
- RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Spicer – Universal Joint (Part No.5-1350X)
from
$45.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More
National – Drive Shaft Center Support Bearing (Part No.HB-88107-A)
from
$44.99
Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.
Product Features:
See More
Product Features:
- BUILT TO LAST – Advanced heat treatment process for strength
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
- RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6056)
from
$21.49
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHECKER 55-82; CHEV 60-12; DODGE 57-02; FORD 55-10; GMC 63-07; INTL 57-02; ISUZU 96-01; KW 81-18; MACK 80-90; MAZDA 87-94; MITS 87-09; OLDS 90-01; PLYM 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1955-2018
- Weight approx: 3 Lbs
- BEARING ID / BORE: 1.3780 INCH / 35 MM
- CENTERLINE: 2.28 INCH / 58 MM
- MOUNT WIDTH: 6.62 INCH / 168 MM
- STYLE: ROUND FRAME
- COMPLETE MOUNT
Driveworks – Wheel Bearing: Direct Fit, 1 Piece (Part No.S-5707)
from
$15.99
Driveworks wheel bearings are a direct replacement for original parts at a much more affordable cost. Each wheel bearing is engineered to meet or exceed OE specifications, and goes through intensive quality control inspections to ensure proper fitment. Manufactured using high-precision machinery and advanced heat treatment processes, these bearings are designed for maximum durability and extended periods of use under any driving condition. Specific to certain applications, Driveworks bearings have multi-lip seals built into the bearing for increased protection against invasive contaminants and premature wear.
Product Features:
See More
Product Features:
- Depending on the application, specified Driveworks wheel bearings have integrated encoder rings that automatically sync with the vehicle’s anti-lock braking system (ABS) upon successful installation
- Engineered, manufactured, and tested to meet or exceed OE specifications
- Integrated seal design improves contamination resistance for a longer bearing life
- High performance grease is used to lubricate the inner raceway to ensure smooth operation, higher operating temperatures, and minimal noise
- Manufactured from high quality steel to maximize durability under even the harshest driving conditions
- Brand may vary by location
Driveworks – Cylindrical Bearing (Part No.S-R1561TV)
from
$31.99
Value-priced bearing meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
Driveworks – Ball Bearing (Part No.S-HB-88107-A)
Driveworks – Drive Shaft Center Support (Part No.S-HB-88508-A)
from
$29.49
Drive Shaft Center Support
National – Tapered Roller Bearing Cone (Part No.HM88649)
from
$19.79
Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
- OE-STYLE DESIGN – Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Yukon Gear – R1559Tv Rear Axle Bearing And Seal Kit (Part No.10001)
from
$52.99
Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1559TV axle bearing and seal kit, TorringtonBrand, 2.530″ OD, 1.620″ ID This axle bearing & seal kit services one side only.
Product Features:
See More
Product Features:
- Includes axle bearing and seal
- Services one side
- Torrington Brand
- 2.530″ O.D.
- 1.620″ I.D.
Yukon Gear – C/Clip (Part No.33083)
from
$8.99
C/Clip for Chrysler 8.25″, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 8.2″, 8.5″ & 8.6″.
Product Features:
See More
Product Features:
- c-clip for Chrysler 8.25″, Ford 8.8″, GM 12 bolt car and truck and GM 8.2″, 8.5″ and 8.6″
- .150″ thick
Yukon Gear – Adapter Sleeve Fro GM 8.6" & 9.5" Yokes To Use Triple Lip Pinion Seal (Part No.41150)
from
$24.99
Product Features:
See More
- Fits GM 8.6″ and 9.5″
- Sleeve to adapt standard yoke to use late model triple lip pinion seal
Yukon Gear – GM 7.5"/8.0"/8.5"/8.6" Rear Axle Bearing And Seal Kit (Part No.10005)
from
$89.99
Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. axle bearing and seal kit for C10 Aero truck, 2.800″ OD, 1.620″ ID. This axle bearing & seal kit services one side only.
Product Features:
See More
Product Features:
- Includes axle bearing and seal
- Services one side
- 2.800″ O.D.
- 1.620″ I.D.
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6053)
from
$38.99
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CHEV 60-02; DODGE 64-66; FORD 75-15; GMC 60-02;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1960-2015
- Weight approx: 3 Lbs
- BEARING ID / BORE: 1.5750 INCH / 40 MM
- CENTERLINE: 2.28 INCH / 58 MM
- MOUNT WIDTH: 6.62 INCH / 168 MM
- NO STUDS
Yukon Gear – Axle Seal, For 1559 Or 6408 Bearing (Part No.30201)
from
$7.99
Axle seal, for 1559 OR 6408 bearing, NOT COARSE spline 12T.Yukon Mighty seal.
Product Features:
See More
Product Features:
- Rear axle seal
- 2.530″ O.D.
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6035)
from
$13.49
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CHEV 58-02; GMC 55-02; INTL 57-02;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1955-2002
- Weight approx: 2 Lbs
- BEARING ID / BORE: 1.1811 INCH / 30 MM
- CENTERLINE: 3.50 INCH / 89 MM
- MOUNT WIDTH: 1.50 INCH / 38 MM
- COMPLETE MOUNT
Most Popular 1990 GMC C1500 Transfer Cases
Customize your GMC with 10 Transfer Cases products
like Input Shaft Bearings,
Transfer Case Output Shaft Seals, and
Input Shaft Seals, all
priced under $94.99.
Driveworks – Oil Seal (Part No.S-9613S)
from
$4.99
Value-priced seal meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
National – Shaft Repair Sleeve (Part No.99187)
from
$36.49
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Designed to repair damaged, grooved or worn shafts
- Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
- Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
- Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
- Easy to install with removable flange and installation tool
Driveworks – Oil Seal (Part No.S-9449)
from
$5.49
Value-priced seal meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
National – Bearing (Part No.LM67048)
from
$7.79
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION — Crowned raceways and rollers for even load distribution
- OE-STYLE DESIGN — Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Driveworks – Taper Bearing Cone (Part No.S-M-88048)
from
$11.29
Value-priced bearing meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
National – Multi-Purpose Seal (Part No.4529N)
from
$14.49
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Design type: spring loaded; single-lip
- Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
- Resistance to EP lubricants
- Low swell in hydrocarbon fluids
- Delivers quality and reliable performance for every type of repair
Driveworks – Taper Bearing Cone (Part No.S-HM-88649)
from
$19.49
Value-priced bearing meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
National – Bearings (Part No.N-1211-L)
from
$94.99
Product Features:
See More
- BUILT TO LAST: Advanced heat treatment process for strength
- PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
- RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
- COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on
National – Shaft Repair Sleeve (Part No.99176)
from
$46.99
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Designed to repair damaged, grooved or worn shafts
- Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
- Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
- Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
- Easy to install with removable flange and installation tool
Driveworks – Manual Transmission Input Shaft Seal (Part No.S-481181-N)
Top Picks for 1990 GMC C1500 Differentials
Upgrade GMC C1500s with top-quality Differentials parts, including 279 OEM and aftermarket selections for your 1990 model.
Mobil 1 – 75W-90 Full Synthetic Gear Lubricant, Extends Gear Life, 1 Quart (Part No.26101)
from
$19.99
Mobil 1 Synthetic Gear Lubricant LS 75W-90 is a supreme, multi-purpose automotive gear lubricant that helps to provide exceptional thermal stability and resistance to high temperature oxidation, extending gear life due to minimal deposits. Helps to deliver outstanding protection against low speed/high torque wear with the capability to handle severe driving conditions while delivering smooth efficient performance. Mobil 1 Synthetic Gear Lubricant LS provides exceptional shear stability, corrosion protection, and enhanced frictional properties. Compared to conventional hypoid gear lubricants, Mobil 1 LS 75W-90 performs exceptionally over a wide range of temperatures to reduce wear at start up. Mobil 1 gear lube helps to minimize leakage and reduce contamination while providing good resistance to foaming to maintain film strength for reliable lubrication. Meets or exceeds the requirements of the following industry specifications: API GL-5.
Product Features:
See More
Product Features:
- Mobil 1 LS synthetic automotive gear lubricant exceeds the highest level of performance requirements of modern passenger vehicles
- Helps to provide exceptional thermal stability and resistance to high temperature oxidation and extend gear life due to minimal deposits
- Delivers outstanding protection against low speed/high torque wear, handling severe driving conditions with smooth, efficient performance
- Compared to conventional hypoid gear lubricants, performs exceptionally over a wide range of temperatures to reduce wear at start up
- Provides exceptional shear stability, corrosion protection, and enhanced frictional properties
- Manufacturer Part Number: 104361
Valvoline – DEXRON – VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart (Part No.822405)
from
$14.49
Valvoline DEXRON-VI/MERCON LV ATF is a full-synthetic transmission fluid formulated with advanced additive technology to meet and exceed the requirements of the General Motors DEXRON-VI specification. It is officially licensed and approved by GM and is fully back-serviceable and can be used wherever DEXRON-II and/or DEXRON-III are recommended. Recommended for use in the following applications: DEXRON-VI, DEXRON-III, DEXRON-II, and Allison C-4.
Product Features:
See More
Product Features:
- Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
- Enhanced anti-shudder protection for smooth shifting and maximum power transfer
- Developed with anti-wear technology to help improve transmission durability
- Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures
National – Bearing Race (Part No.M88010)
from
$7.99
Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION – Crowned raceways for even load distribution
- OE-STYLE DESIGN – Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Dorman – Differential Cover (Part No.697-711)
from
$63.99
This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.
Product Features:
See More
Product Features:
- Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles
- Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid
- Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
- Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
National – Bearing Race (Part No.LM501314)
from
$9.29
Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION – Crowned raceways for even load distribution
- OE-STYLE DESIGN – Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Driveworks – Oil Seal (Part No.S-2043)
from
$7.99
Value-priced seal meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
Motive Gear – Differential Pinion Shim Kit (Part No.1100)
from
$7.99
High-quality Differential Component Shim
Product Features:
See More
Product Features:
- SHIM KIT FITS-8.25-F7.5-AMC20-GM0
Powertrax – Grip LS Traction System (Part No.LS201030)
from
$503.99
For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!
See More
Motive Gear – Differential Carrier Gear Kit (Part No.GM10BI-30)
Motive Gear – Differential Ring and Pinion (Part No.GM10-342A)
Felpro – Axle Housing Cover Gasket Oval Shaped 10 Bolt Hole Gasket (Part No.RDS 55028-1)
from
$10.99
Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Felpro – Axle Housing Cover Gasket: Irregular Shaped 14 Bolt Hole Gasket (Part No.RDS 55387)
from
$8.99
Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Validated for fit, form and function
- Unsurpassed quality you can trust
National – Wheel Bearing: Direct Fit, 1 Piece (Part No.R-1561-TV)
from
$53.99
Product Features:
See More
- STRONG AND DURABLE – Controlled heat treatment process for strength and durability
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for durability and performance
- OE-STYLE DESIGN – Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- Professional technicians know they can depend on National
Motive Gear – Differential Ring and Pinion (Part No.GM10-373A)
National – Multi-Purpose Bearing (Part No.A-5)
from
$16.99
Product Features:
See More
- CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
- PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
- OE-STYLE DESIGN: Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Dorman – Help – Differential Shaft Lock Bolt (Part No.81048)
from
$6.79
This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Dorman – Differential Yoke including Seal and Pinion Nut (Part No.697-500)
from
$139.99
Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this differential end yoke matches the fit and construction of the original yoke
- Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
- Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
- Validated fit – this differential end yoke has been tested to confirm accurate fit
Dorman – Differential Cover (Part No.697-700)
from
$37.99
This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.
Product Features:
See More
Product Features:
- Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles
- Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid
- Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
- Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
Motive Gear – Differential Ring and Pinion (Part No.GM10-373)
Motive Gear – Differential Master Bearing Kit – Koyo (Part No.R10RMK)
Motive Gear – Differential Master Bearing Kit – Timken (Part No.R10RMKT)
from
$135.99
Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv
Product Features:
See More
Product Features:
- KIT BRG & SEAL GM 10 BOLT MASTER NON IFS FRONT / REAR
Richmond Gear – Differential Ring And Pinion (Part No.49-0034-1)
from
$342.99
Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!
Product Features:
See More
Product Features:
- For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
- The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
- Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
- Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
- Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.
Motive Gear – Differential Master Bearing Kit – Koyo (Part No.R10REMK)
from
$113.99
Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv
Product Features:
See More
Product Features:
- GM 10 BOLT 8.5″ MSTR KIT W/EATON OR AUBURN PRO
Motive Gear – Differential Carrier Gear Kit (Part No.GM9.5BI)
In-Demand Universal Joints for 1990 GMC C1500s
Select from 54 premium Universal Joints parts for your 1990 GMC C1500, with prices ranging from $4.59 to $449.99.
Spicer – Universal Joint, Greaseable 1330 Series OSR (Part No.5-213X)
from
$42.99
When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.
Product Features:
See More
Product Features:
- OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
- Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
- The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
- Zerk allows for lubricating at regular intervals to help extend the life of the part.
MOOG Driveline Products – Universal Joint Strap Kit (Part No.492-10)
from
$15.99
By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.
Product Features:
See More
Product Features:
- For U-Joints 330, 330A, 331 & 331A
- Contains two 1.66″ bolt center clamps and four 5/16-24 x 1-5/16″ cap screws
MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.354C)
from
$34.99
Product Features:
See More
- INHIBITS GALVANIC REACTION – Designed specifically for aluminum yokes to avoid a galvanic reaction that leads to corrosion
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
- CORROSION PROTECTION – Bearing cups and snap rings are chemically-coated to protect aluminum yokes
- KEEPS DIRT OUT – Nitrile rubber grease seals with double lip design protects components from wear-causing contaminants
- GREASABLE DESIGN – Radial design of bearing cups allows 360 Degrees lubricant distribution to all bearing surfaces to flush out contaminants and moisture to reduce corrosion and wear
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
Spicer – Universal Joint, Greaseable S44 To 1330 Series (Part No.5-212X)
from
$45.99
When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.
Product Features:
See More
Product Features:
- OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
- Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
- The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
- Zerk allows for lubricating at regular intervals to help extend the life of the part.
MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.354)
from
$34.99
Product Features:
See More
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
- KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
- Cross forging shape and flash provide easier installation and high strength
MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.534G)
from
$42.99
Product Features:
See More
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
- KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
- Cross forging shape and flash provide easier installation and high strength
Driveworks – Universal Joint (Part No.DW-534G)
from
$15.99
Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).
Product Features:
See More
Product Features:
- The cross is hot forged for the higher torque and horsepower
- The bearing cups are made by cold forging to provide higher strength and better rigidity
- Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
- Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
- Grease fitting allows for easy maintenance and the flexible use of the entire assembly
- Snap rings are held to strict tolerances to ensure proper cup position and retention
- Nitrile rubber seals are applied to optimize grease retention and reduce contamination
Driveworks – Universal Joint (Part No.DW-354)
from
$31.99
Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).
Product Features:
See More
Product Features:
- The cross is hot forged for the higher torque and horsepower
- The bearing cups are made by cold forging, having higher strength and better rigidity
- Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
- Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
- Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
- Snap rings are held to strict tolerances to ensure proper cup position and retention
- Nitrile rubber seals to optimize grease retention and reduce contamination
MOOG Driveline Products – Universal Joint Strap Kit (Part No.530-10)
from
$11.99
By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.
Product Features:
See More
Product Features:
- For U-Joints 355, 372 & 534G
- Contains two 1.81″ bolt center clamps and four 5/16-24 x 1-5/16″ cap screws
MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.254)
from
$29.99
Product Features:
See More
- BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
- KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.234)
from
$29.49
Product Features:
See More
- BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
- KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.355)
from
$26.99
Product Features:
See More
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
- KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
- Cross forging shape and flash provide easier installation and high strength
MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.290)
from
$34.99
Product Features:
See More
- BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
- GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
- KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.355C)
from
$37.99
Product Features:
See More
- INHIBITS GALVANIC REACTION – Designed specifically for aluminum yokes to avoid a galvanic reaction that leads to corrosion
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
- CORROSION PROTECTION – Bearing cups and snap rings are chemically-coated to protect aluminum yokes
- KEEPS DIRT OUT – Nitrile rubber grease seals with double lip design protects components from wear-causing contaminants
- GREASABLE DESIGN – Radial design of bearing cups allows 360 Degrees lubricant distribution to all bearing surfaces to flush out contaminants and moisture to reduce corrosion and wear
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
Spicer – Universal Joint (Part No.5-795X)
from
$45.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More
Neapco – Universal Joint (Part No.2-3010)
MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.232)
from
$37.99
Product Features:
See More
- BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
- GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
- KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.235)
from
$19.99
Product Features:
See More
- BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
- GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
- KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Driveworks – Universal Joint (Part No.DW-331)
from
$15.99
Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).
Product Features:
See More
Product Features:
- The cross is hot forged for the higher torque and horsepower
- The bearing cups are made by cold forging, having higher strength and better rigidity
- Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
- Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
- Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
- Snap rings are held to strict tolerances to ensure proper cup position and retention
- Nitrile rubber seals to optimize grease retention and reduce contamination
MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.270)
from
$42.99
Product Features:
See More
- BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
- GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
- KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.231)
from
$37.99
Product Features:
See More
- BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
- KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.331)
from
$41.99
Product Features:
See More
- BUILT TO LAST – Rugged design specifically engineered for fleets, off-highway and commercial vehicles
- STRONG AND DURABLE – Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
- KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
- GREASEABLE DESIGN – Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
- INHIBITS PREMATURE WEAR – Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
- RELIABLE PERFORMANCE – Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
Spicer – Universal Joint, Greaseable S44/3R Series (Part No.5-3147X)
from
$36.99
When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.
Product Features:
See More
Product Features:
- OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
- Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
- The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
- Zerk allows for lubricating at regular intervals to help extend the life of the part.
Driveworks – Universal Joint (Part No.DW-355)
from
$15.99
Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).
Product Features:
See More
Product Features:
- The cross is hot forged for the higher torque and horsepower
- The bearing cups are made by cold forging, having higher strength and better rigidity
- Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
- Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
- Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
- Snap rings are held to strict tolerances to ensure proper cup position and retention
- Nitrile rubber seals to optimize grease retention and reduce contamination
Most Sold 1990 GMC C1500 4WD Components
Explore our best-selling GMC parts for the 1990 C1500 among 1 OEM and aftermarket options starting from $9.99.
Carquest Premium – Multi-Use Connector (Part No.PTA1271)
from
$9.99
Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.
Product Features:
See More
Product Features:
- Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
- WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
- Product constructed to meet all design and operating characteristics as intended by the manufacturer.
- OE specified wire gauge to ensure a reliable electrical connection
- Designed to meet or exceed OE specifications in form, fit and function
Top-Rated Drivetrains Brands For Your 1990 GMC C1500
Shop for the best-rated brands offering Drivetrains and other products for your 1990 GMC C1500s. Below you’ll find some of our best rated Drivetrains from National, DriveWorks, and Motive Gear, and more. Drivetrains from these brands that fit a 1990 C1500 start at just $4.99 and are rated as high as 4.3 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.
Popular National 1990 GMC C1500 Drivetrains
When it comes to maintaining or upgrading your 1990 GMC C1500, using quality Drivetrains is essential to ensure durability and a perfect fit. National ticks all of those boxes. We offer a wide selection of National Drivetrains, specifically designed for the 1990 GMC C1500. With over 3 National brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $7.99, with an average price of just $10.42. Plus, with over 15 customer reviews and an average rating of 4.3 stars, you can trust that our National Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.
from
$7.99
(4)
Bearing Race
“Goes with M88010 bearing cup.
Application was the pinion bearing race for a Ford 9 Inch on a 1957 Ford F-100.”
Popular DriveWorks 1990 GMC C1500 Drivetrains
DriveWorks auto parts is one of the highest quality Drivetrain brands in the market. Any 1990 GMC C1500 owner should feel confident when installing genuine DriveWorks parts in their vehicle. To ensure the best fit and performance for your 1990 C1500, Advance Auto Parts carries a full inventory of 3 DriveWorks Drivetrains. Plus you will be keeping your GMC in peak condition while saving money because prices on these DriveWorks Drivetrains range from $4.99 to $15.99, plus, with more than 5 customer reviews and an impressive 4.3 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.
from
$7.99
(1)
Oil Seal
“Didn’t fit my 1992 K1500 10 bolt 8.5″ ring gear rear end. Was told wrong part.”
FAQs for 1990 GMC C1500 Drivetrains
Which Drivetrains are best-sellers for 1990 GMC C1500s?
Out of 395 Drivetrains that fit 1990 GMC C1500s, the following parts are the top sellers:
- 75W-90 Full Synthetic Gear Lubricant, Extends Gear Life, 1 Quart (7070039) – $19.99
- DEXRON – VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart (12079201) – $14.49
- Axle Housing Cover Gasket Oval Shaped 10 Bolt Hole Gasket (5185823) – $10.99
What’s the price range for 1990 GMC C1500 Drivetrains?
Drivetrain prices for the 1990 GMC C1500 start at $2.59 and go up to $2,304.99 for the most premium parts.
What’s the average price of a Drivetrain for a 1990 GMC C1500?
The average price for Drivetrains for the 1990 GMC C1500 is $270.81. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.
Does Advance Auto Parts sell Drivetrains for other GMC C1500 model years?
What are the cheapest Drivetrains for my 1990 GMC C1500?
The cheapest 1990 GMC C1500 Drivetrains we carry in stock are:
- Differential Pinion Gear Washer (10282533) – $2.59
- Ring Gear Bolt (20520168) – $2.99
- Differential Crush Sleeve (20520169) – $2.99
- Differential Cross Shaft (10282201) – $2.99
- Differential Ring Gear Bolt (10282159) – $2.99
What are the top-rated Drivetrains that fit the 1990 GMC C1500?
Out of 11,676 reviews by customers, our 1990 GMC C1500 Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 1990 GMC C1500 and their top-rated products:
- Universal Joints
- Universal Joint Strap Kit (10198342) – $15.99
- Universal Joint, Greaseable S44 To 1330 Series (10841133) – $45.99
- Universal Joint, Greaseable 1330 Series OSR (10854997) – $42.99
What types of Drivetrains do you sell for my 1990 GMC C1500?
As of 11/2/25, these are some of the most in-demand types of Drivetrains for a 1990 GMC C1500:
Can I get help with 1990 GMC C1500 Drivetrain orders?
Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about GMC Drivetrains and more.
What is your return policy for GMC C1500 Drivetrains?
Advance Auto Parts keeps returns simple. For new GMC C1500 Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.
