from

$61.19

All the quality and performance you’ve come to expect from MSD is now available in black. Our customers have requested black parts for their builds so we’ve answered with the addition of several black distributor caps and cap and rotor kits. The black parts are built to the exact specifications of the traditional MSD red components. If you’re looking to change up the look under the hood of your street machine, off-road rig or race car; check out the complete line of MSD black components.

Product Features:

Injection Molded From DuPont Rynite Material
Extreme strength; high dielectric properties
Designed with performance in mind
High quality; voltage insulating material
Brass terminals
Black in color

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$439.99

The B&M Quicksilver features a ratcheting action for positive shifts, Chrome Knob, neutral safety switch, NHRA/IHRA approved Reverse Lockout. Fits Most 3 and 4 speeds.

Product Features:

Universal Floor Mount Application
Base Trimmed For Custom Fit
Cable Operated
Quick Installation
Accurate Shifting

from

$59.99

K&N’s replacement air filters are designed to increase horsepower and acceleration while providing excellent filtration. We make over 1,200 different replacement air filters for virtually every vehicle on the road. These filters are washable and reusable

Product Features:

Designed to boost horsepower and rate of acceleration
Can be cleaned and used again
High air flow with exceptional filtration
Lasts up to 50,000 miles before cleaning is required depending on driving conditions
Works with original equipment manufacturer vehicle electronics
Emissions legal in all 50 US states
Will NOT void vehicle warranty
Million Mile Limited Warranty®

from

$91.99

Put an end to high maintenance point ignition systems by utilizing a specialized electronic circuitry and an infrared signal. Stabilizes ignition timing from 1 to 10,000 RPM. Improves performance and fuel efficiency, easy to install with hand tools, reduces maintenance. It is built with the latest thermal clad based surface mount construction for maximum dependability and long life.

Product Features:

Most Accurate Ignition Timing System
Improves Performance And Fuel Economy
Easy To Install With Simple Hand Tools
Reduced Maintenance
Eliminates Changing Points

from

$56.99

The cap and rotor of any ignition system must be considered maintenance items. Just as you change the oil and filter of your car, you should always replace the cap and rotor as a set. To make things easy, we now offer these cap and rotor replacement kits.

Product Features:

Designed w/Performance In Mind
High Quality Material
Stainless Terminals

from

$420.99

For Ford enthusiasts that are serious about performance! Just under the brass terminals of the MSD cap and rotor is an easy-to-adjust mechanical advance assembly. The assembly is fine blanked from chromoly steel, rig-welded for strength plus receives a QPQ coating. The precision weights glide on nylon bushings for smooth advancement and different springs and stop bushings are supplied so a variety of advance curves can be tuned. The steel shaft that spins the advance and reluctor receives a friction reducing coating plus is guided by a sealed ball bearing and long sintered bushing. This combination provides stable timing signals and spark delivery at any RPM. Triggering chores are handled by MSD’s race proven, maintenance-free magnetic pick-up.

Product Features:

CNC machined billet aluminum housing and DuPont Rynite base
Supplied w/Cap-A-Dapt and rotor (accepts MSD socket style caps)
Must Be Used w/An MSD Ignition Control
Mech. advance assem. can be locked out for crank trigger systems
Nylon pads ensure smooth operation of the advance weights
Advance weight pins are staked and tig welded to the plate
Advance plate and weights are fine blanked from chrome moly steel
QPQ coated for friction reduction

from

$67.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets
For Engine with One-Piece Fuel Pump Eccentric

from

$51.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$217.99

Keith Dorton Series VoluMax race series fuel pump made from heavy duty construction for continuous high RPM operation. Redesigned high flow valves always ensure adequate fuel delivery. Fuel pressure regulator is required. Fuel body casting can be rotated

Product Features:

High Output Fuel Flow
Flows 170+ gph Free Flow
Shutoff Pressure Pre-Set At 8 PSI
Fuel Pressure Regulator Is Not Required
Heavy Duty Construction For Continuous High rpm Operation
Redesigned High Flow Valves Always Ensure Adequate Fuel Delivery
Fuel Body Casting Can Be Rotated For Plumbing Situations
Inlet And Outlet Tapped For 3/8 in. NPT

from

$100.99

Product Features:

Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$237.99

The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.

Product Features:

Cost effective aluminum construction provides superior strength to weight ratio
Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
Durable design increases valve lift while withstanding the rigors of moderate race use
Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.

from

$9.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Saves Your Tie Rods
Lasts Longer
Looks Great

from

$20.99

Mr. Gasket Performance Timing Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Manufactured from high-density cork/rubber blend gasket material
Provides excellent sealing and durability
For OE replacement, high performance street, drag race and oval track use

from

$185.99

Flexplt: Bb Ford 70-97 (164T)

from

$104.99

The best all-round choice for vehicles with leaf or coil springs. Properly loads rear wheels to prevent over-reaction and wheel hop.

Product Features:

Excellent Weight Transfer
Lets Front End Down Quickly
Maximum Traction
Makes Vehicle Safer
Easier Control At End Of Track
Better Overall Stability

from

$158.99

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

Custom Fit For Make And Model Listed
Wires Are Pre-Cut To Exact Specifications
Bolt-on Performance
Conductor core features DuPont Kevlar material for increased tensile strength
Durable outer sleeve is a proprietary compound for resistance to high heat or abrasion
Stainless steel terminals feature dual crimp tabs to grip wire conductor and outer jacket separately

from

$43.99

Super Intake Manifold Bolts

from

$36.99

Graphite impregnated facing and a steel expanded metal core. Superior tensile strength. Resists cracking and withstands intense heat. Resists deteriorating. Anti-stick properties and easy removal for disassembly.

Product Features:

Graphite-Impregnated Facing
Steel Expanded Metal Core
Superior Tensile Strength
Resists Cracking
Withstands Intense Heat
Resists Deteriorating
Anti-Stick Properties
Easy Removal For Disassembly

from

$438.99

Our advanced power system line has grown to include starters. Our new APS starter is designed to crank over the highest compression engines on a hot day in Death Valley. Not that too many race cars are sitting in Death Valley, but it’s good to know that you have the oomph to make it happen. The APS starter features all new components beginning with a three horsepower motor. This power is used to crank over the reduced 4.4:1 gear set to deliver great torque to the engine’s ring gear to get the engine turning. The armature is balanced during assembly and is guided by two ball bearings for smooth engagement and thousands of starts. The downsized housing clears most headers and oil pans, but just in case, we made the billet mount so it can be clocked in different positions to help in tight applications. The assembly is powder coated MSD red and will stay looking good, even though it’s underneath your car.

Product Features:

Mount Can Be Clocked To Assist In Mounting
Downsized design helps clearance issues w/oil pans and exhaust
Ball bearing supported armature and pinion gear
3 Hp Motor Provides Power For High Compression Engines
Gear reduction of 4.4:1 improves torque for great cranking

from

$103.99

This high performance ignition module provides your plugs with more spark over the stock module. The solid state electronics provide high coil out put and superior reliability. The Dwell control circuit ensures, long consistent coil charging. The current control circuit protects against coil over heating. This module fits most Ford Thick Film Ignition systems. 1984 thru 1993.

Product Features:

Fits Most Stock And Modified Distributors
Dwell Control Circuit
Resists False Triggering

from

$30.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$210.99

Product Features:

Designed for 1500 to 7000 Performance
Large Plenum
Long Tapered Runners
90mm. Throttle Body Opening
Polished Finish

from

$83.99

The Edelbrock #4461 Signature Series Valve Covers are designed for Ford 351M-400 and 351C V8 applications. Engineered for function and styled for great looks, Signature Series valve covers have stock-style breather baffles that prevent oil passage to the PCV valve. These quality valve covers accept all emissions equipment, including PCV valve holes. Rubber grommets for the breather and PCV valve holes are included. Matching breathers sold separately.

Product Features:

Ford 351M-400 & 351C V8
Short
Chrome Steel
Set Of Two
Rubber Grommets For Breather

from

$48.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PTFE offers the best in fluid and high-temperature compatibility and contact sealing surface can run on undersize shafts, seal minor imperfections and virtually eliminate shaft wear.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$50.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$18.99

Oil Pan Bolt Kit

from

$70.99

Replace your stock black engine pulleys with a pair of chrome plated steel pulleys from Mr. Gasket. The pulleys are highly polished then chrome plated for lasting beauty.

Product Features: