1982 Ford E-250 Econoline Differentials

With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.

Product Features:

• Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.

Product Features:

• Ford 7.5″, 8.8″ Ring Gear Bolt

Product Features:

• Carrier shim kit for Dana Spicer 60, 70, 70HD, 70U and 80

Pinion nut for Ford 7.5″, 8″, 8.8″, 9 3/8″ & 9″. 1 1/6″ socket, 3/4″ x 20 thread.

Product Features:

• Pinion nut for Ford 7.5″, 8″ and 9″
• 3/4″ x 20 thread
• 1 1/6″ socket

Product Features:

• Crush sleeve
• Fits Ford 9.75″
• Conversion crush sleeve to install 2011 and up ring and pinion set into 2000-2010 housing

8.6″ GM 99-08 PINION Bearing & SEAL KIT .

Product Features:

• Pilot bearing
• Fits Ford 9″
• 0.656″ thick

10.25″ Ford TracLoc pinion gear Thrust washer.

Product Features:

• Pinion gear thrust washer
• Fits Ford 10.25″ with Trac Loc positraction

Yukon round replacement yoke companion flange for Dana 60 and 70. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Dana Spicer 60 and 70
• 29 spline
• 5.00″ O.D.
• 8 x 4.25″ bolt pattern
• Round companion flange

Flat side gear without hub for 9″ Ford with 31 splines.

Product Features:

• Side gear without hub
• Fits Ford 8″ and 9″ Trac Loc positraction with 31 spline axles

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

• Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
• 0.225″ diameter
• 1.870″ long

Product Features:

• Inner oil slinger for Dana Spicer 60

Differential

Trac Loc clutch guide for 9″ Ford.

Product Features:

• Clutch guide
• Fits Ford 8″ and 9″

Product Features:

• Clutch kit
• Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
• 18 piece kit
• Steel clutches

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

0.260″ diameter cross pin roll pin for 8.75″ Chrysler, 8″, 9″ Ford, and Model 20 and 35.

Product Features:

• Roll pin for Chrysler 8.75″, Ford 8″ and 9″, AMC Model 20 and Model 35
• 0.260″ diameter

Valvoline High Performance Gear Oil is an extreme pressure gear lubricant formulated with quality base oils and superior additives that helps protect against severe temperatures, shock loads, scuffing, scouring, corrosion and pitting in high speed, high load, high torque and high horsepower conditions.

Product Features:

• Formulated for reliable gear protection
• Protects against severe temperatures to help extend service life
• Formulated with extreme-pressure additives to minimize gear wear from shock loads
• Helps protect against gear wear from scuffing, scouring, corrosion and pitting
• Recommended for conventional hypoid differentials and non-synchronized manual transmissions in passenger cars, light trucks, sport utility vehicles, vans and heavy-duty trucks where an API-GL5 or GL-4 fluid is specified
• PLEASE NOTE: Valvoline recommends SynPower Full Synthetic Gear Oil for limited slip differentials

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

• Fits standard rotation Dana Spicer 60
• 9.75″ ring gear diameter
• 29 spline pinion
• 12 ring gear bolts
• 4.11 ratio

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Ford 9″ with35 spline pinion
• For oversize applications
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings
• Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits Ford 9″ with LM104911 carrier races and Daytona pinion support
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve eliminator, pilot bearing, thread locker, marking compound with brush and gasket.

Spartan spring & pin kit, fits larger designs.

Product Features:

• Fits Dana Spicer 60
• Replacement alignment pin and spring kit

Seal housing for Ford 10.25″ & 10.5″, Zip locker, with o-rings.

Product Features:

• Seal housing for Ford 10.25″ and 10.5″
• Includes o-rings

Product Features:

• Bulkhead quit connect fitting

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! This unit has been machined for use in dropouts with a load-bolt. All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This locker also fits 9.5″ & 10″ dropouts.

Product Features:

• Fits Ford 9″ with 35 spline axles and loadbolt housing
• Patented internal design reduces common locker failures
• 8620 internals for added strength
• Assembled in the USA

Side gear thrust washer (0.750″ shaft) for 8.8″ Ford.

Product Features:

• Side gear thrust washer for Ford 8.8″
• 0.750″ diameter cross pin shaft applications only