1982 Ford E-250 Econoline Drivetrains

Essential 1982 Ford E-250 Econoline Drivetrains

Yukon Gear – Forged Yoke For Ford 8.8" With A 1350 U/Joint Size (Part No.41051)

Forged Yoke For Ford 8.8" With A 1350 U/Joint Size

from

$246.99
Yukon forged yoke for Ford 8.8″ with a 1350 U/joint size (stronger than billet). 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:
  • Fits Ford 8.8″
  • 30 spline
  • 1350 u-joint size
  • Outside snap ring design
  • 3.625″ snap ring span
  • 1.188″ cap diameter
  • U-bolt style
See More

Yukon Gear – 20 Long Air Line For Zip Locker (Part No.34002)

20 Long Air Line For Zip Locker

from

$29.99
20 long air line for Zip Locker.

Product Features:
  • Air line
  • 20′ in length
See More

Yukon Gear – Ford 10.25" Rear Axle Bearing And Seal Kit (Part No.10034)

Ford 10.25" Rear Axle Bearing And Seal Kit

from

$274.99
Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. Axle bearing and seal kit for 10.25″ Ford (full-floating). This kit includes Timken inner and outer bearings and races along with high quality seals. Unit is sold per side and is covered for one year against manufacturing defects. This axle bearing & seal kit services one side only.

Product Features:
  • Fits Ford 10.25″
  • Includes inner and outer bearings and races and axle seal
  • Services one side
See More

USA Standard Gear – 9" Ford Spartan Locker Cross Pin, Short (Part No.17022)

9" Ford Spartan Locker Cross Pin, Short

from

$26.99
9″ Ford Spartan locker cross pin, short.

Product Features:
  • USA Standard Gear heavy-duty cross pin shaft
  • Fits Ford 9″
  • Works with Spartan Locker or standard open spider gears
  • Short shaft for four pinion designs
See More

Yukon Gear – Standard Open Side Gear And Thruster Washer For 10.25" Ford (Part No.33293)

Standard Open Side Gear And Thruster Washer For 10.25" Ford

from

$11.99
55P Chevy Passenger Drop Out gasket.

Product Features:
  • Side gear thrust washer
  • Fits Ford 10.25″
See More

Yukon Gear – High Performance Ring & Pinion Gear Set For Ford 8.8" In A 3.31 Ratio (Part No.24351)

High Performance Ring & Pinion Gear Set For Ford 8.8" In A 3.31 Ratio

from

$369.99
Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:
  • Fits standard rotation Ford 8.8″
  • 8.80″ ring gear diameter
  • 30 spline pinion
  • 10 ring gear bolts
  • 3.31 ratio
See More

Dorman – Rear Differential Cover (Part No.697-702)

Rear Differential Cover

from

$34.99
This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.

Product Features:
  • Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles
  • Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid
  • Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
  • Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
See More

Yukon Gear – Dana 44 JK / 60 / 70U Pinion Nut Washer Replacement (Part No.33164)

Dana 44 JK / 60 / 70U Pinion Nut Washer Replacement

from

$3.99
Product Features:
  • Pinion nut washer for Chrysler 7.25″, 8.25″, 8.75″ with 29 spline pinion, Jeep JK rear, Dana Spicer 60, 70, 70U and 70HD and 2007-2010 Ford 10.5″
See More

Yukon Gear – 9" Ford Gasket (Part No.23012)

9" Ford Gasket

from

$11.99
9″ Ford gasket.

Product Features:
  • Dropout gasket
  • Fits Ford 9″
See More

Yukon Gear – 1541H Alloy, 8 Lug, Left Hand Replacement Rear Axle For ’95-’10 Dana 60, E150/ E250/ E350 (Part No.21157)

1541H Alloy, 8 Lug, Left Hand Replacement Rear Axle For '95-'10 Dana 60, E150/ E250/ E350

from

$329.99
Yukon 1541H alloy, 8 lug, left hand replacement rear axle for ’95-’10 Semi Float Dana 60, Ford E Series Vans with a length of 34.13″ inches and 35 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a semi float axle.

Product Features:
  • 35 spline
  • 8 lug
  • 34.13″ long
  • Fits Dana Spicer 60 in 1995-2002 Ford E250
  • Left hand side
  • Semi-float axle
See More

National – Bearings (Part No.HM88542)

Bearings

from

$22.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Crowned raceways and rollers to ensure even load distribution for maximum life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Yukon Gear – Replacement Carrier Shim Kit For Dana 60, 61 & 70U (Part No.55020)

Replacement Carrier Shim Kit For Dana 60, 61 & 70U

from

$104.99
Product Features:
  • Carrier shims for Dana Spicer 60 and 70U
See More

Yukon Gear – The Carrier Bearing Puller (Part No.56072)

The Carrier Bearing Puller

from

$883.99
The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:
  • Carrier bearing puller
  • Works with an impact gun to safely and easliy remove carrrier bearings
See More

Dorman – Help – Driveshaft Flange Bolts (Part No.80992)

Driveshaft Flange Bolts

from

$20.29
This drive shaft bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:
  • Direct replacement – this engine mount bolt matches the fit and function of the factory part on specified years, makes and models
  • Ideal solution – this drive shaft bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

SKF – Pinion Seal (Part No.J7010201578SKF)

Pinion Seal

from

$19.04
Pinion Seal

National – Bearings (Part No.LM102910)

Bearings

from

$6.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Crowned raceways and rollers to ensure even load distribution for maximum life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Yukon Gear – Trac Loc Friction Plate, 4 Tab (Part No.16177)

Trac Loc Friction Plate, 4 Tab

from

$21.99
Product Features:
  • Friction plate
  • Fits Ford 8″ and 9″ Trac Loc positraction
See More

Yukon Gear – Set Up Bearing (Part No.56039)

Set Up Bearing

from

$276.99
Set-up carrier bearing kit (2 bearings, no races) for Dana 60 and 70. 387A. No return.

Product Features:
  • Set up bearing kit
  • Fits Dana Spicer 60
  • Easily slips on and off carrier journals to allow for easier carrier shim adjustment
See More

Yukon Gear – Bearing Race Driver (Part No.56010)

Bearing Race Driver

from

$215.99
Bearing race drive for Ford 10.25″ and 10.5 axle bearing. (TK 3920). No return.

Product Features:
  • Bearing race driver
  • Fits 3920 race
  • All steel construction
See More

Yukon Gear – Bearing Install Kit For Ford 8.8" Differential (Part No.11042)

Bearing Install Kit For Ford 8.8" Differential

from

$217.99
Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:
  • Fits 2009 and down Ford 8.8″
  • Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve , marking compound and brush.
See More

Yukon Gear – Minor Install Kit For Ford 9.75" Differential (Part No.12041)

Minor Install Kit For Ford 9.75" Differential

from

$142.99
Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:
  • Fits Ford 9.75″
  • Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.
See More

Yukon Gear – Seal Housing For Ford 10.25" & 10.5", Zip Locker, With O-Rings (Part No.34040)

Seal Housing For Ford 10.25" & 10.5", Zip Locker, With O-Rings

from

$78.99
Seal housing for Ford 10.25″ & 10.5″, Zip locker, with o-rings.

Product Features:
  • Seal housing for Ford 10.25″ and 10.5″
  • Includes o-rings
See More

Yukon Gear – Short Yoke For ’92 And Older Ford 10.25" And 10.5" With A 1410 U/Joint Size (Part No.41041)

Short Yoke For '92 And Older Ford 10.25" And 10.5" With A 1410 U/Joint Size

from

$381.99
Yukon short yoke for ’92 and older Ford 10.25″ and 10.5″ with a 1410 U/joint size. 4.188″ snap ring span, 1.118″ cap diameter. Outside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:
  • Fits 1992 and down Ford 10.25″
  • 31 spline
  • 1410 u-joint size
  • Outside snap ring design
  • 4.188″ snap ring span
  • 1.188″ cap diameter
  • U-bolt style
See More

Yukon Gear – Dana 60 & Dana 70 Power Lok Case Bolt (Part No.33236)

Dana 60 & Dana 70 Power Lok Case Bolt

from

$7.99
Dana 60 & Dana 70 Power Lok case bolt.

Product Features:
  • Power Lok case bolt for Dana Spicer 60 and 70
  • 7/16 x 14 thread
  • 3.5″ long
  • 9/16″ hex head
See More

Yukon Gear – Replacement Pinion Depth Shims For Dana 60, 61 & D70-U (Part No.55012)

Replacement Pinion Depth Shims For Dana 60, 61 & D70-U

from

$17.99
Product Features:
  • Pinion depth shims for Dana Spicer 60 and 70U
See More

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6038)

Center Support Bearing Motor Mount: Center, 1 Piece

from

$34.49
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHEV 60-02; DODGE 57-02; FORD 55-07; GMC 63-02; INTL 57-02; KW 81-18; MACK 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:
  • MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
  • HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
  • READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
  • For Years: 1955-2018
  • Weight approx: 4 Lbs
  • BEARING ID / BORE: 1.5750 INCH / 40 MM
  • CENTERLINE: 2.48 INCH / 63 MM
  • MOUNT WIDTH: 6.62 INCH / 168 MM
  • STYLE: ROUND FRAME
  • NOT PICTURED: TWO DUST SHIELDS
See More

Yukon Gear – Replacement Cover Gasket For Dana 50, Dana 60 & Dana 70 (Part No.23007)

Replacement Cover Gasket For Dana 50, Dana 60 & Dana 70

from

$13.99
Product Features:
  • Cover gasket
  • Fits Dana Spicer 60, 70, 70U and 70HD
See More

National – Bearings (Part No.208-LO)

Bearings

from

$49.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Controlled heat treating process for lasting performance and extended bearing life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Popular 1982 Ford E-250 Econoline Drivetrains Categories

1982 Ford E-250 Econoline Drivetrains

You count on your 1982 Ford E-250 Econoline to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 241 Drivetrains ranging in price from $2.59 to $1,487.99, you’re sure to find everything you need for your 1982 Ford E-250 Econoline.

Brands matter. If you want to shop a specific Drivetrains brand, we stock 17 different brands like Moog, National, and Driveworks. 1982 Ford E-250 Econoline Drivetrains start as low as $2.59!

One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 4,461 extensive product reviews on 1982 Ford E-250 Econoline Drivetrains. Some of the top-rated Drivetrains products we carry are Multi Purpose Bearing with 3.4 stars and Wheel Bearing: Direct Fit, 1 Piece with 4.4 stars.

Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 1982 Ford E-250 Econoline below to get started!

Top-Rated Drivetrains Brands For Your 1982 Ford E-250 Econoline

Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1982 Ford E-250 Econoline running right for years to come. In our inventory you’ll find brands like Moog, National, Driveworks, and even more.

Popular Spicer Drivetrains

You’ll find popular Spicer brand products across Universal Joints. All are waiting to get your 1982 Ford E-250 Econoline back on the road. Some of the top-rated Spicer products in these categories are:
Universal Joint
from $39.99
(5)
Universal Joint
U-Joints

FAQs for 1982 Ford E-250 Econoline Drivetrains

What are the most purchased Drivetrains for the 1982 Ford E-250 Econoline?

Out of 241 Drivetrains for the 1982 Ford E-250 Econoline, the most popular in our inventory are:
Universal Joint
from $15.99
(65)
Universal Joint
U-Joints
Bearings
from $16.99
(17)
Bearings
Input Shaft Bearings
Driveshaft Flange Bolts
from $20.29
(1)
Driveshaft Flange Bolts
Drive Shaft Support Bolts

What are the top-rated 1982 Ford E-250 Econoline Drivetrains?

Top-rated Drivetrains for your 1982 Ford E-250 Econoline based on customer reviews/ratings are:
Multi Purpose Bearing
from $44.99
(25)
Multi Purpose Bearing
“Fit just like the old one.”
Wheel Bearing: Direct Fit, 1 Piece
from $52.99
(20)
Wheel Bearing: Direct Fit, 1 Piece
“USA made”
Multi Purpose Bearing
from $73.99
(17)
Multi Purpose Bearing
“Muy bueno y se ajusto como si fuera original”