1981 Toyota Celica Fluids and Chemicals

Extended Protection Automatic Transmission Fluid – 6 Quarts

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• MAXLIFE TECHNOLOGY PREVENTS engine breakdown with 40% better wear protection than the industry standard
• REFRESH AGING SEALS AND PREVENT LEAKS with seal conditioners
• REDUCE SLUDGE, DEPOSITS, CORROSION, AND RUST with added detergents – keep motors clean inside
• ENHANCED FRICTION PERFORMANCE HELPS MAXIMIZE POWER with advanced friction-fighting agents
• MEETS OR EXCEEDS ALL REQUIREMENTS of ILSAC GF-6A, API SP, API SN with SN PLUS, API SN

High Performance Motor Oil API LICENSED MOTOR OIL Royal Purple High Performance Motor Oil combines premium base oils with proprietary additive technologies to create a high performance synthetic engine oil that optimizes performance and protection. Royal Purple High Performance Motor Oils carry the current API and ILSAC engine oil licenses, as well as the GM dexos1 gasoline engine oil approval. ILSAC GF-6 AND GM DEXOS1 Modern gasoline direct injection (GDI) engines have achieved levels of power and fuel economy never before possible in passenger car engines. As a result, smaller engines operate at much higher loads across all engine speeds. This has caused increased wear in critical areas of the engine, and created a destructive phenomenon called low-speed pre-ignition (LSPI). The unique, state-of-the-art additive technology in Royal Purple High Performance engine oils is designed specifically to address these issues, and help engines maintain performance and reliability.

Product Features:

• Better Wear Protection
• Increased Protection against Low Speed Pre-Ignition
• Increased Fuel Efficiency
• Better Protection for Vehicle Exhaust Emissions Equipment
• Improved Compatibility with Fuels Containing Ethanol
• Superior Corrosion Protection
• Made in USA

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• MAXLIFE TECHNOLOGY PREVENTS engine breakdown with 40% better wear protection than the industry standard
• REFRESH AGING SEALS AND PREVENT LEAKS with seal conditioners
• REDUCE SLUDGE, DEPOSITS, CORROSION, AND RUST with added detergents – keep motors clean inside
• ENHANCED FRICTION PERFORMANCE HELPS MAXIMIZE POWER with advanced friction-fighting agents
• MEETS OR EXCEEDS ALL REQUIREMENTS of ILSAC GF-6A, API SP, API SN with SN PLUS, API SN
• MaxLife Technology: Valvoline High Mileage with MaxLife Technology is specially formulated to maximize engine life in vehicles with over 75,000 miles, providing superior protection against wear, friction, heat, and deposits.
• Synthetic Blend Composition: This motor oil features a unique combination of synthetic and premium conventional oils, ensuring optimal performance and protection for high-mileage engines.

Product Features:

• Reduces heat & wear
• Eliminates TQ converter shudder & clutch pack chatter
• For all automatic transmissions & 4×4 transfer cases

Product Features:

• Fully Synthetic
• Advance transmission protection from standard to sever duty
• Resist thermal breakdown, oxidation, varnish and sludge

Automatic transmission fluid is a technologically advanced, low viscosity formulation specially designed to deliver performance and maximum fuel efficiency for modern automatic transmissions.

Product Features:

• Full Synthetic, low viscosity formulation
• OEM approved and licensed by Ford (MERCON® LV) and GM (DEXRON® -VI)
• Low viscosity formula for maximum fuel efficiency in modern automatic transmissions
• Enhanced friction durability for smooth transmission performance
• Superior high temperature protection to effectively resist oxidation
• Unsurpassed protection against copper corrosion
• Industry Specifications and OEM Approvals: JASO-1A
• Licensed and approved for use in: All GM vehicles (DEXRON®-VI, All previous DEXRON®); All Ford vehicles which specify Mercon® LV

FRAM DEX III/MERC ATF is formulated for older model Ford and General Motors  vehicles requiring MERCON®, DEXRON-I®, DEXRON-II® and DEXRON-III®. It is also  recommended for transmissions, power steering systems, and hydraulic systems  requiring a DEXRONIII® or Caterpillar TO-2 fluid. FRAM DEX III/MERC ATF may also  be used in compressors, pumps, and hydraulic systems. FRAM DEX III-H/M ATF is  recommended for use in all transmissions, hydraulic systems, and power steering units  manufactured by American, European, Korean, Japanese and other manufactures from  around the world specifying DEXRON®III H/Mercon® and earlier DEXRON®/Mercon® type transmission fluids.

Product Features:

• Good foam and corrosion prevention
• Safe for seals
• Promotes smooth shifting
• ALWAYS REFER TO YOUR VEHICLES OPERATING MANUAL TO SELECT THE CORRECT GRADE FLUID FOR YOUR TRANSMISSION
• TRANSMISSION FLUIDS ALSO APPLICABLE IN POWER STEERING UNITS; CHECK OWNERS’ MANUAL

Castrol Transmax ATF/CVT Universal is a technologically advanced full-synthetic formulation designed to deliver excellent performance in most of the traditional stepped automatic transmissions and Continuously Variable Transmissions currently in use. It is also suitable for use in hybrids.

Product Features:

• Coverage of over 300 specs/95% of vehicles in operation
• Broad scope of vehicle applications improves workshop efficiency and inventory management
• Enhanced friction durability for smooth transmission performance
• Superior high temperature protection to effectively resist oxidation

ZEREX G05® is the automaker approved original chemistry used in newer Ford®, Chrysler® and Mercedes-Benz® automotive and diesel engines. Its Hybrid Organic Acid Technology (HOAT) chemistry combines the best of conventional and organic acid-based chemistry to provide the ultimate protection against rust and corrosion. ZEREX G05 antifreeze/coolant uses the highest quality virgin ethylene glycol for freeze and boil over protection and a hybrid organic acid corrosion inhibitor package to protect your engines from liner pitting and corrosion.

Product Features:

• Automaker approved technology. Provides protection for 5 years / 150,000 miles in light duty applications and 3 years / 300,000 miles in heavy duty applications
• Formulated for long life performance
• Low-silicate, low-pH and phosphate-free formula
• Helps protect all cooling system metals, including aluminum

PEAK ORIGINAL EQUIPMENT TECHNOLOGY ANTIFREEZE + COOLANT for ASIAN VEHICLES is a line of premium coolants specifically designed to match the technology and color requirements of Asian vehicles. Each coolant is formulated with the same corrosion inhibitor technology that protected your vehicle straight from the factory. Color cues on the packaging and a list of covered vehicles on the front label make it easy to identify the right match for your specific vehicle. PEAK ORIGINAL EQUIPMENT TECHNOLOGY ANTIFREEZE + COOLANT for ASIAN VEHICLES – RED/PINK is an ethylene glycol-based antifreeze/coolant specifically developed for use in any Asian vehicle requiring a Red or Pink phosphate-enhanced organic acid technology (POAT) formulation. It contains high-quality organic acid corrosion inhibitors and is free of borate, nitrite, silicate and amines chemicals. PEAK ORIGINAL EQUIPMENT TECHNOLOGY ANTIFREEZE + COOLANT for ASIAN VEHICLES – RED/PINK meets the performance requirements of ASTM D3306 and JIS K2234. With a complete flush and fill, PEAK guarantees this coolant will provide service life protection of up to 150,000 miles or 5 years.

Product Features:

• Matches each Asian vehicle manufacturer’s technology and color requirements
• Protects all cooling system metals from rust and corrosion
• Meets the performance requirements of ASTM D3306 and JIS K2234
• Service life of up to 5 years/150,000 miles with a complete cooling system flush and fill
• Color-coding and vehicle applications listed on the front simplify selecting the right antifreeze/coolant
• Available as both concentrate and 50/50 products to do the job right
• Testing Requirements: For proper freeze and boil over protection, use a traditional refractometer or hydrometer to measure the percentage of ethylene glycol by volume.

FRAM Conventional Green Concentrate is an ethylene glycol-based product for use in car and light duty trucks that are already using a conventional coolant. The inhibitors prevent rust, corrosion, and provide freeze-up and boil-over protection. When used as directed, the Prime Green Concentrate Low Silicate formula provides full protection for a minimum of one year.

Product Features:

• Low Silicate Formula
• When used as directed, will provide protection for a minimum of 1 year
• Meets or exceeds ASTM requirements for cars, light duty trucks
• Concentrated formula. Must mix with high quality (distilled/deionized) water to the desired ratio. Can be used for top-off, complete drain and refill or flush and refill of the cooling system.

Prestone All Vehicles antifreeze+coolant (ready to use) is truly designed to work with all vehicles; all makes, models, years & fluid colors. It is designed to work with all new engines while also being backwards compatible improving protection in all older engines. The patented Cor-Guard technology (the best innovation in the category in decades) instantly protects parts from corrosion, buildup, pitting, scaling, rust and other damage. These fluids are specially designed to not only manage the engine temp and protect from freezing up (like competitors), but they also potect the engine from damage. Internal damage can cause engine part failure, leading to expensive repairs and serious inconveniences. Avoid costly repairs and vehicles in the shop with Prestone All Vehicles antifreeze+coolant. This fluid is designed to last 10yrs / 300,000 miles and also to protect the internal parts of the engine for 10yrs / 300,000, offically patented by Prestone.

Product Features:

• Formulated to work with All Vehicles. Works with all fluid colors; All OAT, POAT, HOAT & IAT.
• Longer Engine Life Guarantee – 10 Yr., 300,000 mile Extended life formula.
• Includes patented Prestone CorGuard technology, the best advancement in cooling system parts protection that protects against rust and corrosion of all cooling system metals, including aluminum. Protection for 300,000 miles.
• Ready to Use formula (prediluted to a 50% Eg & 50% distilled water mix). Perfect for small volume top-off or complete drain and refill of the cooling system

Prestone® MAX American Vehicles Power Steering Fluid (PSF) + Stop Leak maximizes and increases system life + the power to stop leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. This formula is also great at preventing leaks by rejuvenating seals before they leak. This synthetic fluid is designed with 2X Anti-wear System Protection, which means more protection against pump failure, squeals and clogs. 100,000 mile fluid life, 2X more than conventional fluid, extends the time between replacement. This fluid is formulated for American vehicle manufacturers: Ford, Lincoln, Mercury, Dodge, Ram, Jeep, Chrysler, GMC, Chevrolet, Buick, Cadillac, Pontiac, Oldsmobile and others. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 100,000 Mile Fluid Life. Synthetic Formula for longer life and more protection
• MAX + Stop Leak. Stop Leak Additives to prevent and stop power steering system leaks.
• For use in American vehicle manufacturers: Ford, Lincoln, Mercury, Dodge, Ram, Jeep, Chrysler, GMC, Chevrolet, Buick, Cadillac, Pontiac, Oldsmobile and other
• 2X Anti-Wear Protection for enhanced System Life vs. conventional fluid. More protection against pump failure, squeals and clogs

Prestone® Power Steering Fluid (PSF) delivers increased system life. Designed with Anti-wear System Protection, Prestone PSF protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 50,000 Mile Fluid Life
• Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber & gasket components.
• For use in all manufacturers
• Conventional Formula – For use in all manufacturers

Prestone® Power Steering Fluid + Stop Leak (PSF+SL) delivers increased system life and prevents & stops system leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. The stop leak additives also prevent leaks by rejuvenating seals before they leak. Also designed with Anti-wear System Protection, Prestone PSF+SL protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 50,000 Mile Fluid Life
• Includes Stop Leak Additives to prevent and stop power steering system leaks.
• Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber & gasket components.
• Conventional Formula – For use in all manufacturers

Prestone® Power Steering Fluid + Stop Leak (PSF+SL) delivers increased system life and prevents & stops system leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. The stop leak additives also prevent leaks by rejuvenating seals before they leak. Also designed with Anti-wear System Protection, Prestone PSF+SL protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 50,000 Mile Fluid Life
• Includes Stop Leak Additives to prevent and stop power steering system leaks.
• Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber & gasket components.
• Conventional Formula – For use in all manufacturers

Power Steering Fluid

PENTOSIN ATF 6 1L

Valvoline SAE 75W-90 Full Synthetic Gear Oil provides the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Engineered to outperform, our detergent package-based formulation contains Full Synthetic basestocks and special additives that help protect parts from rust and corrosion while providing exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity, wear resistance additives that assist in protecting gear teeth, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. Valvoline SAE 75W-90 Full Synthetic Gear Oil is recommended for use in axle applications requiring factory-fill or drain-and-fill levels for limited slip performance. Protect your gears with Valvoline, the #1 gear oil brand.

Product Features:

• EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION , ranging from -30F to 300F degrees
• REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
• FIGHTS CORROSION AND RUST with emulsifying agents and safeguards against impurities, oxidation and thermal breakdown
• MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP HYPOID DIFFERENTIALS where APPI GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4 or MT-1 fluid
• MEETS OR EXCEEDS THE PERFORMANCE REQUIREMENTS for Mack GO-H and GO-J; API GL-5 and API MT-1; MIL-PRF-2105E; and SAE J2360

Mobil 1 advanced full synthetic motor oil 5W-30 helps to extend engine life for vehicles of all ages. Mobil 1 advanced synthetic motor oil is designed to deliver outstanding engine protection from the five factors that can damage engines over time and protect critical engine parts for up to 10,000 miles between oil changes (1) . Its uniform synthetic oil molecules reduce friction, helping to prevent deposits and sludge buildup. Mobil 1 helps to keep your engine running at lower temperatures. (2) This technologically advanced motor oil is proven to cool engine temperatures by over 10%. (3) Its formulation provides excellent internal engine heat protection (up to 500 degrees Fahrenheit), and low-temperature protection (to -30 degrees Fahrenheit), supporting quick cold-weather starting and ultra-fast protection. Mobil 1 advanced full synthetic motor oil meets ILSAC GF-6 standards to help provide low-speed pre-ignition (LSPI) and timing chain wear protection while keeping your engine clean and helping to improve your fuel economy. Mobil 1 advanced full synthetic motor oil 5W-30 also helps control oxidation to prevent oil breakdown and is recommended by ExxonMobil for all types of modern vehicles, including high-performance turbo-charged, and supercharged gasoline and diesel multi-valve fuel-injected engines found in passenger cars, SUVs, light vans, and light trucks. Mobil 1 is America’s leading synthetic motor oil brand at retail¿, recommended by car builders and experienced mechanics, and is the Official Motor Oil of NASCAR®. ( (1) Protects for up to 10,000 miles or 1 year, whichever comes first. To learn more about the Mobil 1 Limited Warranty, visit Mobil.US. (2) Compared to conventional oil. (3) Based on proprietary engine testing¿results may vary. (4) Source: The NPD Group/Retail Tracking Service/Dollar Sales/PCMO Full Synthetic/52 weeks ending February 25, 2023.)

Product Features:

• Mobil 1 advanced full synthetic motor oil 5W-30 helps to protect your engine from the five factors that can damage engines over time
• Helps protect critical engine parts for up to 10,000 miles between oil changes,(1) controlling oxidation to prevent oil breakdown and maintaining excellent viscosity
• Meets ILSAC GF-6 standards to help provide low-speed pre-ignition (LSPI) and timing chain wear protection while keeping your engine clean and helping to improve your fuel economy
• Mobil 1 is specially formulated to help remove sludge and lower engine temperatures
• Provides excellent internal engine heat protection (up to 500 degrees F) and low temperature protection (to -30 degrees F)
• Manufacturer Part Number: 124315
• Versatile Application: Recommended by ExxonMobil for all types of modern vehicles, including high-performance turbo-charged and supercharged gasoline and diesel multi-valve fuel-injected engines found in passenger cars, SUVs, light vans, and light trucks.

Automatic Transmission Fluid – 5 Liter Bottle

Today’s advanced engine technology requires advanced protection. Valvoline Advanced Full Synthetic, the motor oil designed to protect today’s sophisticated engines, contains premium anti-wear additives, superior antioxidants and extra detergents. It protects 40% better against wear, resists oil breakdown 10-times better, and defends 25% more against deposits than industry standards for maximum performance and engine longevity. And with an exceptional range of temperature protection your engine will ready for extreme weather. Valvoline invented motor oil 150 years ago, and we’ve been reinventing it ever since. Get Valvoline Advanced Full Synthetic and give your engine the advanced protection proven to maximize engine life.

Product Features:

• ADVANCED PROTECTION AGAINST the four main causes of engine breakdown: wear friction heat and deposits
• 40% BETTER WEAR PROTECTION vs. industry standard as tested in the Sequence IVB engine test
• 25% BETTER DEPOSIT PROTECTION with superior engine cleaning detergents as tested in the GMOD engine test
• EXCEPTIONAL HIGH/LOW TEMPERATURE PROTECTION defends your motor no matter the weather conditions
• MEETS OR EXCEEDS ALL REQUIREMENTS of ILSAC GF-6A, API SP, API SN with SN PLUS, API SN, GM dexos 1 Gen 3
• Enhanced Oil Stability: Resists oil breakdown 10-times better than industry standards, providing consistent performance and reliability.
• Premium Additives: Contains premium anti-wear additives, superior antioxidants, and extra detergents for maximum performance and engine longevity.

Prestone® MAX DOT 3 Motor Vehicle Brake Fluid is our highest grade formula, maximizing performance vs. DOT standard. Prestone MAX is our best brake fluid at protecting against overheating and brake fade. With 100,000 mile fluid life, our longest life fluid has 2X more miles between replacement than regular Prestone DOT 3. Prestone MAX has superior performance in severe braking conditions when compared to regular Prestone DOT 3, which means even more piece of mind about the braking system. This synthetic fluid starts with our highest dry boiling point giving our best protection against performance decline due to water absorption. Prestone MAX DOT 3 is safe to use in all DOT 3 braking systems, ABS, disc or drum, and can mix with any DOT 3 fluid. Mixing Prestone MAX with other fluids will lower the performance rating for miles and boil points, for best results replace completely with Prestone MAX DOT 3. It is recommended to only use the DOT fluid specified for your car. Using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 100,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with Our Highest Grade Formula. Prevents corrosion of all metals within the braking system.
• Superior Protection in Extreme Braking Conditions
• Synthetic, Long Life Formula – 2X Longer than regular Prestone DOT 3

Prestone® DOT 3 Motor Vehicle Brake Fluid delivers enhanced performance vs. DOT standards, benefitting all vehicles calling for DOT 3. This synthetic fluid starts with a higher dry boiling point than the DOT minimum standard to protect against overheating, brake fade and performance decline due to water absorption. This extended life (50,000 mile) fluid is also formulated to prevent corrosion of all metals within the braking system.  This formula is safe to use in all DOT 3 braking systems (ABS, disc or drum) and can mix with any DOT 3 fluid.  It is recommended to only use the DOT fluid specified for your car, as using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 50,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with High Grade Formula*
• Protects against performance decline due to water absorption. Prevents corrosion of all metals within the braking system.
• Synthetic, Extended Fluid Life Formula