from

$32.59

Product Features:

Prevents Air Inclusion
Direct Replacement
For OE Bleeders
One Person Bleeds Safely
Without The Mess
No Chance Of Air Bubbles

from

$100.99

Product Features:

Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$23.99

Spectre’s Ford small block water neck fits 1965 – 19475 Ford 221, 289, 302 and 351W engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes the bolts and sealing O-ring, and also features a 1/2 inch outside diameter by-pass hose connection.

Product Features:

Fits 1965 – 19475 Ford 221, 289, 302 and 351W engines
Includes bolts and sealing O-ring
Has additional 1/2 inch by-pass hose fitting
Chrome plated
Designed for OEM fit
Easy to install

from

$128.99

These ACCEL carbon and graphite core wire sets virtually eliminate RFI noise, while providing maximum conductivity for ultimate performance in any race or street application. Double silicon insulation eliminates leakage and misfire.

Product Features:

Heavy Duty 8.8mm Oversized Silicone Jacket
500 Ohms/ft. Of Resistance
550 Degree Double Silicone Construction
Fiberglass Braid
Carbon/Graphite Core
Magnetic Suppression
Fiberglass/Kevlar Core
500 Ohms Resistance

from

$226.99

Product Features:

FORD 9″ EMPTY POSI CASE – 28 & 31 SPLINES

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$38.59

Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Silicone beading on both sides of each gasket
Complete with manifold end seals and distributor gasket
For OE replacement, high performance street, drag race and oval track use
Creates Tight Leak proof Seal

from

$19.99

Hooker’s precision-matched Super Competition header gaskets provide a sure fit and unmatched exhaust sealing. This OEM quality gasket is constructed of a thick ,.060 inch, high temperature, non-asbestos fiber laminate with a perforated steel core, which provides a superior grip and adhesion. This construction also contributes to exact fit compliance between the cylinder head and header flange, offering excellent sealing properties during extreme temperature and operating conditions.

Product Features:

Tear Resistant
Precisely Cut To Match Header

from

$144.99

Product Features:

Polished Finish
Raised Fins w/Black Mat Background
Detailed With Allen Hex Heads
2 Piece Look; 1 Piece Construction
Clears Most Roller Rockers
Clears Valvetrain Components
Heavy Gauge

from

$210.99

Product Features:

Designed for 1500 to 7000 Performance
Large Plenum
Long Tapered Runners
90mm. Throttle Body Opening
Polished Finish

from

$85.29

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

Service Part
No Moving Parts To Wear Out
Self Contained Unit
Can Drive OEM
Can Drive High Performance Ignition Coils

from

$788.99

Dual Valve Springs from COMP Cams are manufactured from Super Clean wire and subject to extensive quality control testing to deliver a valve spring assembly with superior strength, durability and valve train stability, no matter what the application. The dual spring design creates a stronger valve spring that can easily handle the increased lift found in extreme stress applications. COMP Cams Dual Valve Springs exceed the expectations of today’s engine builders and racers.

Product Features:

Seat pressure: 112 lbs. @ 1.900″, Open Pressure: 355 lbs. @ 1.200″
O.D.: 1.509″, I.D.: 0.697″
Dual valve springs with damper

from

$426.99

The award-winning Quarter Stick automatic shifter is designed to provide positive gear change control for street or racing transmission applications. Gated mechanism. NHRA/IHRA approved reverse lockout.

Product Features:

Forward and Reverse Shift Patterns
Chrome Plated Trigger for Detent Activity
Factory Neutral Safety Switch
Compact And Lightweight
Roller Detent with Shifter Pattern

from

$20.99

Performance mechanical advance springs.

Product Features:

PerTronix D700700 Advance Spring Kit Flame-Thrower Billet Distributor
Performance mechanical advance springs.

from

$58.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$200.99

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:

High Output Fuel Flow
Flows 130+ gph Free Flow
Shutoff Pressure Pre-Set From 7.5 To 9 PSI
Fuel Pressure Regulator Is Not Required
Heavy Duty Construction For Continuous High rpm Operation
Redesigned High Flow Valves Always Ensure Adequate Fuel Delivery
Fuel Body Casting Can Be Rotated For Plumbing Situations
Inlet And Outlet Tapped For 3/8 in. NPT

from

$42.49

Excellent high performance replacement for import and domestic vehicles with canister type oil filled coil. Re-engineered windings for even higher energy output resulting in quicker starting improved throttle response and more high RPM power. Designed to work with Points style and Breakerless electronic ignition systems. Heavy duty black Alkyd tower provides in flashover in protection to primary terminals. ACCEL Yellow can. 42000 volts effective up to 6500 RPM 1.4 ohms on the primary

Product Features:

42000 Volts
Effective To 6500 RPM
Quicker Starting
Improved Throttle Response
Higher RPM Power
Can Finished In Yellow

from

$43.99

Super Intake Manifold Bolts

from

$81.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets

from

$59.19

High performance, race quality gasket with molded rubber coating over a steel core. Steel core provides rigidity and durability, preventing prevent push out while the molded rubber coating helps seal minor oil pan rail irregularities. The one piece design eliminates the need for separate end seals to make installation easier and even further reduce the possibility of oil leakage. Provides excellent sealing and durability. Excellent replacement for stock original equipment, high performance street, drag race and oval track. Includes gasket and new oil pan bolts.

Product Features:

Steel core provides rigidity, durability and prevents gasket push out
Molded rubber coating seals minor irregularities in pan surface
One piece design is easier to install and even less prone to leak
Direct replacement suitable for all uses – street, racing, heavy duty
Include both gasket and new oil pan bolts
No Cork Particles
Easy Removal For Disassembly

from

$72.99

Shift Improver Kit – 1970 to 1982 Ford, Lincoln, Mercury C4 Application: 1970 to 1982 Ford, Lincoln, Mercury C4 Recalibrate your automatic transmission for optimum performance and extended life! Select the mode that best suits your application Provides crisp shifts on any stock automatic transmission Eliminates shift overlap and excess wear on clutches and bands due to slippage The B&M Shift Improver Kit the easiest way to get the stout performance you’ve always wanted out of your automatic transmission – and you get two modes of performance to select from: Heavy Duty, or Street/Strip. It’s our least expensive and simplest to install kit. All you need are some hand tools! In the space of an afternoon, you can turn your transmission into a B&M-tuned unit! Ask the thousands of satisfied customers that have installed one in their transmissions! STAGE 1. HEAVY DUTY Firm positive shifts without loss of driver comfort for improved performance in all street vehicles. Recommended for regular passenger vehicles. STAGE 2. STREET/STRIP Provides positive shifts for high performance street use or for competitive events. This level is for the enthusiast who wants the hardest, quickest possible shift.

Product Features:

Provides Crisp Shifts
On Any Stock Automatic Transmission
Eliminates Soft/Sluggish Shift
Eliminates Shift Overlap
Eliminate Clutch and Band Wear
Improves Transmission Life
Transmission Removal Not Required

from

$9.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Saves Your Tie Rods
Lasts Longer
Looks Great

from

$427.99

These COMP Cams Ultra-Gold Aluminum Roller Rocker Arms with a 3/8″ stud diameter and 1.6 ratio are designed for Ford V8 289-302-351W applications. The new modern design features of these Ultra-Gold Rockers are proven to withstand extremely aggressive spring pressure and valve lift. Designed specifically for high performance street and race engines, the Ultra-Gold Aluminum Rocker Arms are precision CNC-machined to strict tolerances. Developed to meet the demands of professional engine builders, these rockers include features never before possible in an aluminum rocker arm.

Product Features:

CNC-machined, lightweight design removes weight and yields unrivaled quality and ratio accuracy
Designed for high performance street and race engines
Precision-sorted trunion bearings withstand elevated valve spring pressure and valve lift
Additional clearance, up to 1.650″ O.D. valve spring

from

$284.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$60.99

MSD Ignition is a company built on Customer Satisfaction and Service. That is why all of MSD products go through regimented test procedures before they are ever packaged and shipped. MSD stands behind its products for one full year after purchase

Product Features:

Rotor phasing can be adjusted.
Ideal When Atomic TBI Is Controlling The Timing

from

$48.09

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:

Indicates coolant temperature
Helps prevent coolant injuries
Fahrenheit and centigrade readings
Color-coded temperature ranges
Integrated coolant reclamation valve
Improves under-hood appearance
Chromed crown with a colored trim ring

from

$399.99

MSD engineers fit all of their high performance distributor experience into a special compact housing designed to be less obtrusive for Ford engines. The diameter of the special cap and housing are 5/8 inch smaller than stock Ford distributors providing extra room in front of the engine. The new MSD cap features spark plug style terminals and is firmly screwed down to the housing. The distributor relies on MSD’s race proven magnetic pick-up and precision reluctor to deliver accurate trigger signals to the MSD ignition throughout high rpm. The reluctor assembly is turned by a hardened steel shaft which rides in a sealed ball bearing for high rpm stability and endurance. Mounted to the top of this shaft is a fully adjustable mechanical advance assembly. The rate at which the chromoly assembly advances the timing is easily controlled by changing the supplied advance springs and stop bushing for total advance.

Product Features:

Billet housing 5/8 in. smaller dia. than stock Ford distributors
Must Be Used w/An MSD Ignition Control
Supplied w/small dia. cap w/HEI style terminals; race and rotor
Will accept PN[8441] Cap-A-Dapt
Nylon pads ensure smooth operation of the advance weights
Advance weight pins are staked and tig welded to the plate
Mech. advance assem. can be locked out for crank trigger systems
Advance plate and weights are fine blanked from chrome moly steel

from

$22.99

Adds a dramatic amount of performance and durability to any vehicle, cars, trucks and SUVs. Helps the vehicle be in control – when maneuvering through turns, during standing start accelerations, braking, even over bumps and berms. Made of Energy’s Hyper-Flex performance polyurethane which lasts 5 -10 times longer than conventional rubber components.

Product Features: