from

$53.99

304 stainless steel mesh. 5 layer construction. Most durable filters in the industry. Outperforms the others in clean air testing. Assures cleanest air possible from washable filter. Provides balance between air flow and peak filtration. Lifetime no hassle warranty.

Product Features:

Multi-Layer Construction
Most Durable Filters In The Industry
Outperforms The Others In Clean Air Testing
Assures Cleanest Air Possible From Washable Filter
Washable And Reusable
Made In The USA
Lifetime No Hassle Warranty

from

$1243.99

Designed for carburetor V8 engines. Power increases from 200 to 400 horsepower. Simple to install. Shorter spray bars. More even distribution across the plenum. A more balanced air and fuel ratio. Quicker response time.

Product Features:

Designed For Carbureted V8 Engines
Power Increases From 200-400_ HP
Simple To Install
Shorter Spray Bars
More Even Distribution Across The Plenum
A More Balanced Air/Fuel ratio
Quicker Response Time

from

$442.99

The Edelbrock #4162 Classic Series Valve Covers are designed for Ford FE V8 1958-1976 applications. Edelbrock first made these aluminum valve covers in the late ’50s and they’re still a classic. They are made of heavy-gauge sand-cast aluminum, Overall height is measured from base to top at the highest point. Edelbrock classic valve covers can be machined to accept breathers if desired.

Product Features:

Ford FE V8 1958-76
Tall
Polished Aluminum
Set Of Two

from

$16.99

Cap off your radiator with a gleaming chrome plated filler cap. Made to last.

Product Features:

Chrome radiator caps
Made to last
Skin packaged

from

$50.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$54.99

Spectre’s Ford V8 water neck fits Ford 429 – 460 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes sealing O-ring, and has a 3/8 inch NPT threaded hole for the Ford temp sensor.

Product Features:

Fits Ford 429 – 460 engines
Has a 3/8 inch NPT threaded hole for temperature sensor
Includes sealing O-ring
Chrome plated
Easy to install
Hardware not included

from

$149.99

Kits include most popular chrome dress-up components, including short, OEM height valve covers with integral oil baffles.

Product Features:

Includes oil baffles
Chrome plated

from

$449.99

When you start making serious power with your EFI Ford, the stock distributor shaft is one of the weak links of the engine. These Pro-Billet models answer the need for an affordable replacement in a strong and great looking package. Each distributor starts as a solid billet that is secured into a state of the art computer numerical control (CNC) machine where it is transformed into a precision housing. Inside each housing there is a sealed ball bearing at the top of the shaft. This design is responsible for accurately guiding the oversized polished steel shaft throughout the entire RPM range of your engine. The shaft is also QPQ-coated for friction reduction and corrosion resistance. The Pro-Billet distributors use a stock-style trigger pick-up to accept factory connectors. For installation, you simply remove the stock distributor and bolt the Pro-Billet MSD in place!

Product Features:

Drop in billet replacement for late model Ford TFI 5.8L dist.
Supplied w/steel gear to work w/factory roller camshafts
Factory style ignition module connector accepts factory wiring
CNC machined billet aluminum housing and billet aluminum base
QPQ coated polished steel shaft; guided by sealed ball bearings
Supplied w/Late Model Distributor Cap And Rotor
Legal to install in all 50 states

from

$467.99

The B&M Megashifter has it all, form, function and classic style. This all adds up to bring you a quality shifter that’s been one of the most popular automatic shifters of all time. The light truck Megashifter is better suited for truck and bench seat applications with its overall height of 14.85-inches tall (2.25-inches taller than #80690 Megashifter.) The positive ratcheting action won’t allow you to over-shift and miss a gear at that critical moment, along with the reverse lockout feature meets NHRA/IHRA safety rules for those weekend grudge races at the track, while the look and feel of the T-handle and accordion style shift boot really shows off its racing heritage. Other features include a black console that you can trim to match the contour of your vehicle’s floor, 5-foot long shifter cable, cable brackets, transmission shift levers, chrome plated top plate with lighted gear indicator and everything needed for an easy at home installation. An optional T-handle with a 12-volt button is available separately for actuating a trans-brake, nitrous oxide or other accessories for the hard-core performance enthusiast. This shifter fits most popular Chrysler, Ford and GM 3 and 4-speed automatic transmissions. Note: AOD transmissions require optional kit #40496, GM 4L60E through 4L85E transmissions with PRNDL switch will require optional kit #70499. Overall Dimensions – 14.9L x 6.4W x 14.8H

Product Features:

Universal Floor Mount Application
Cable Operated
Quick Installation
Accurate Shifting
NHRA/IHRA Reverse Lockout Meets Requirements
Use w/Reverse Pattern Valve Body
Includes Neutral Safety Switch
Includes Backup Light Switch

from

$9.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Saves Your Tie Rods
Lasts Longer
Looks Great

from

$17.99

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

from

$27.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$368.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$113.99

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

Easy Installation
Improved Fuel Economy
Reduced Maintenance
Accurate Timing
Improved Performance
Provides A Simple Conversion
No Moving Parts To Wear Out

from

$108.99

Transpak – 1970 to 1982 Ford, Lincoln, Mercury C4 Recalibrate your automatic transmission for optimum performance Select the mode that best suits your application Improves transmission life Transmission removal not required APPLICATION: 1970 to 1982 Ford,

Product Features:

Recalibrate Auto. Transmission
Optimum Performance
Select Your App. Mode
Improves Transmission Life
Trans. Removal Not Required

from

$45.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$766.99

Product Features:

Designed For Carbureted V8s
Power Increases From 100-250 HP
Precision EDM Machined Spray Bars
Simple To Install

from

$338.99

A higher than stock stall speed as delivered by a B&M Converter will provide several advantages. The high stall converter allows the engine to launch the car at a higher RPM where more torque is available and increased strength.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$190.99

Edelbrock part #9659 Pushrods are designed for small-block Ford 351W V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise f

Product Features:

7.7 in. Length
0.312 in. Diameter
4130 Chromoly Steel Material
Black Oxide Finish
Made In The USA

from

$40.99

Super Intake Manifold Bolts

from

$100.99

Product Features:

Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$29.99

Product Features:

Timing Chain Only

from

$26.99

Made of high durometer, very firm, Hyper-Flex performance polyurethane. They’re economical, increase efficiency and are easy to install. Use Energy Suspension sway bar end links with sway bar bushings to get the maximum performance benefit. Combine both for the same effect as buying a larger sway bar. Together they offer a dramatic improvement in performance and handling.

Product Features:

Made from HYPER-Flex Polyurethane
Allows Vehicle to Work At Maximum Efficiency
Easy to Install
Superior Performance and Greater Longevity
Lasts Much Longer Than OEM Rubber End Links

from

$358.99

Edelbrock #88433 Water Pump Ford 1970-78 302 & 1970-87 351w v8 black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cool

Product Features:

Standard Impeller Rotation
0.625 in. Pilot Shaft
0.750 in. Ball/Ball Bearing
5.70 in. Block To Hub Height
Black Finish

from

$98.99

These coils feature advanced bobbin technology, highly specialized silicone magnetic steel cores, along with optimized winding, resistance and turns ratios to delivery 10-15 percent more energy than the OEM coils. Specialized high temperature epoxy resist

Product Features:

Oil Filled For Better Cooling
Optimized Low Resistance
Silicon Magnetic Steel E-Core
Higher Energy/Voltage Outputs
Quicker Starts
Improved Idle Quality
Resists Shock And Vibration
Resists Corrosion

from

$35.99

This gear test fixture features variable rpm and oil pressure control allowing MSD engineers the ability to maintain the exact conditions that they want for gear tests. Severe loads can be placed on the gear and the fixture can spin up to 10,000 rpm. Features increased outer hardened layer thickness (RC 55-60). Micro polished surface for smooth contact. Proprietary formulated ductile iron. Melonite QPQ coated reduces friction and initial wear. Interstitial carbide concentration improves wear resistance and running properties.

Product Features:

Increased outer hardened layer thickness (RC 55-60)
Micro Polished Surface For Smooth Contact
Proprietary formulated ductile iron.
Melonite QPQ coated reduces friction and initial wear
Interstitial carbide improves wear resistance/running properties

from

$31.99

These performance polyurethane components help reduce common wheel roll-under. This occurs when stopping abruptly, especially when using performance tires for both front of rear drive vehicles is so equipped. Replaces that original, short lived and too-soft O.E.M, rubber on front wheel drive vehicles – diminishes wheel hop and traction loss during standing start accelerations. Better maintains proper alignment under extreme conditions. Made of Energy’s Hyper-Flex performance polyurethane to add both performance and durability.

Product Features:

Made from HYPER-Flex Polyurethane

from

$30.99

Mr. Gasket standard intake gasket sets are manufactured from a blend of nitrile rubber and fiber, for excellent sealing and durability. They’re precision die-cut for each specific application to ensure a great fit, and can be custom-trimmed for modified ports where needed. The sets come complete with all necessary seals and block-off plates.

Product Features: