1972 Ford Country Squire Performance and Racing Products

Essential 1972 Ford Country Squire Performance and Racing Products

Edelbrock – Water Pump #8845 For Small-Block Ford 1986-93, 5.0L V8, Rev. Rotation, Polished (Part No.8845)

Water Pump #8845 For Small-Block Ford 1986-93, 5.0L V8, Rev. Rotation, Polished

from

$461.99
Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:
  • Maximum Cooling for Street and Racing Engines
  • Internal Passages Are Balanced for Maximum Flow
  • Impeller is Larger than Others For Max Pressure
  • Impeller Vanes Dramatically Increase Flow Rates
  • Equal Distribution to Both Sides of Block
  • Only Flows in One-Direction for Optimum Efficiency
See More

Edelbrock – Thunder AVS Carburetor #1825 650 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.1825)

Thunder AVS Carburetor #1825 650 CFM With Manual Choke, Satin Finish (Non-EGR)

from

$427.99
The Edelbrock 1825 Thunder Series AVS 650 CFM manual choke carburetor has been designed and calibrated to deliver optimum off-road performance. Several characteristics make the 1825 Thunder Series AVS 650 CFM manual choke carburetor an outstanding street

Product Features:
  • Spring Loaded Needles/Seat Increase Performance
  • New Qwik-Tune Adjustable Secondary Air Valve
  • Distinctive Black Accented Hardware
  • Lightweight Ball-Burnished Aluminum
  • No Gaskets Below Fuel Level to Prevent Leakage
  • Metering Rod/Step Up Springs Can Be Changed Easily
  • GM/AMC-Style Throttle Linkage
See More

MSD Ignition – Starter; Small Block Ford 289; 302; 351W 5.0L (Part No.5090)

Starter; Small Block Ford 289; 302; 351W 5.0L

from

$438.99
Our advanced power system line has grown to include starters. Our new APS starter is designed to crank over the highest compression engines on a hot day in Death Valley. Not that too many race cars are sitting in Death Valley, but it’s good to know that you have the oomph to make it happen. The APS starter features all new components beginning with a three horsepower motor. This power is used to crank over the reduced 4.4:1 gear set to deliver great torque to the engine’s ring gear to get the engine turning. The armature is balanced during assembly and is guided by two ball bearings for smooth engagement and thousands of starts. The downsized housing clears most headers and oil pans, but just in case, we made the billet mount so it can be clocked in different positions to help in tight applications. The assembly is powder coated MSD red and will stay looking good, even though it’s underneath your car.

Product Features:
  • Mount Can Be Clocked To Assist In Mounting
  • Downsized design helps clearance issues w/oil pans and exhaust
  • Ball bearing supported armature and pinion gear
  • 3 Hp Motor Provides Power For High Compression Engines
  • Gear reduction of 4.4:1 improves torque for great cranking
See More

B & M – Automatic Shifter, Pro Stick Shift with CVR (Part No.80706)

Automatic Shifter, Pro Stick Shift with CVR

from

$429.99
The Original Pro Stick shifter delivers rock-solid performance, mixed with clean design cues and compact size. This is why you see so many Pro Stick shifters at the race track. We start off with a heavy duty steel base with a hardened steel gate plate, a reverse lockout feature that only requires one hand to operate, and complies with NHRA/IHRA safety rules. Then add the billet aluminum shift handle with classic white shift knob, lightweight aluminum trigger and finish it off with a brushed aluminum cover with quick release pins, and you end up with one good looking bullet-proof race shifter. Optional Forward and Reverse shift pattern gate plates are available for most popular 2, 3 and 4-speed transmissions. This model Pro Stick comes out of the box ready for action for most popular 3-speed transmissions, includes a 5-foot Super Duty shift cable, brackets, levers, hardware and detailed instructions for an easy installation. Be sure to check out all the optional Magnum Grip side grip plates including the one and two button 12-volt momentary switches or any of the other accessories we offer for the Pro Stick in the Shifter Accessories section. Notes: AOD requires installation kit #40496, AODE & 4R70W requires installation kit #40504, E40D & 4R100 requires installation kit #40505, 2004R & 700R4 require gate plate #80712, 4L60E – 4L85E equipped with PRNDL switch requires cable bracket kit #70499 and gate plate #80712. Overall Dimensions – 8.25L x 2.92W x 9.25H

Product Features:
  • All One-Handed
  • Reverse Lockout Meets NHRA And IHRA Requirements
  • Mount Directly To Floor/Chassis/Or w/Quick Release
  • Ultimate For Powerglide Applications
  • Lightweight Brushed Alum. Cover
  • Cover Removed Quickly and Easily
  • Includes 5 Ft. Super Duty Race Cable
  • Quick Change Plate Design
See More

Mr. Gasket – Timing Cover Gasket Set (Part No.793G)

Timing Cover Gasket Set

from

$20.99
Mr. Gasket Performance Timing Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:
  • Manufactured from high-density cork/rubber blend gasket material
  • Provides excellent sealing and durability
  • For OE replacement, high performance street, drag race and oval track use
See More

Competition Cams – ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST (Part No.17043-16)

ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST

from

$237.99
The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.

Product Features:
  • Cost effective aluminum construction provides superior strength to weight ratio
  • Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
  • Durable design increases valve lift while withstanding the rigors of moderate race use
  • Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.
See More

MSD Ignition – Wire Set; Black Super Conductor; Ford 351C-460 with HEI Cap (Part No.35383)

Wire Set; Black Super Conductor; Ford 351C-460 with HEI Cap

from

$181.99
The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:
  • Bolt-on Performance
  • Custom Fit For Make And Model Listed
  • Wires Are Pre-Cut To Exact Specifications
See More

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

Mr. Gasket – Valve Cover Gasket (Part No.275)

Valve Cover Gasket

from

$42.49
Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:
  • Manufactured from high-density cork/rubber blend gasket material
  • Provides excellent sealing and durability
  • For OE replacement, high performance street, drag race and oval track use
See More

Mr. Gasket – Engine Rebuilder Overhaul Gasket Kit (Part No.7123)

Engine Rebuilder Overhaul Gasket Kit

from

$87.99
Kits include all gaskets needed for a complete engine overhaul. Cylinder head, intake, exhaust, valve cover and oil pan. Distributor gasket (where applicable), timing cover, fuel pump, thermostat, water pump, and rear main seal. For OE replacement, high performance street, drag race and oval track.

Product Features:
  • Engine Rebuilder
  • Stock/Non-High Performance Engines
  • Includes All Gaskets/Seals
  • Includes all gaskets/seals
See More

Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7821)

Performer-Link Adjustable True-Roller Timing Chain Set

from

$81.99


Product Features:
  • Solid Bushing Chain Resists Stretching
  • For Use with Stock or Edelbrock Camshafts
  • Stressproof Steel Crank Gears
  • 3 Keyway Setting Points To Ensure Accurate Timing
  • True Bearing Surface Rolls with the Sprockets
See More

Weiand – Action +Plus; Intake Manifold (Part No.8010)

Action +Plus; Intake Manifold

from

$349.99
New Everbright(TM) Manifold coating now available on the most popular Weiand and Holley intakes uses proprietary vacuum metalizing technology combined with a protective clear powdercoat to provide long lasting, virtually maintenance free polished looks.

Product Features:
  • Low Rise/Dual Plane Design For Maximum Torque
  • Permanent Mold Casting Process
  • Lighter/Smoother/Better Looking/Consistent Casting
  • Dyno Proven To Make 25hp Over Competition
  • Fully CNC Machined For A Perfect Fit
  • Square Bore Carburetor Flange
  • Exhaust Crossover For Improved Street Drivability
See More

Lakewood – Clutch Fork Pivot Ball-Adj:GM (Part No.15501)

Clutch Fork Pivot Ball-Adj:GM

from

$45.99
Designed to allow additional adjustment of the clutch fork height to eliminate clutch release problems when installing a high performance clutch. Recommended for use with Lakewood safety bell housings. Available for most GM, Ford, and Mopar applications. Adjustable dowel pins correct for improper register bore alignment of bell housing.

Product Features:
  • Allows Additional Adjustment
  • Eliminates Clutch Release Problems
See More

Mr. Gasket – Dust Cap (Part No.2485)

Dust Cap

from

$12.09
If you have custom steel or mag wheels that are not designed without a provision for a center cap, you’re probably looking at an ugly stock dust cap in the center of your front wheels. This chrome dust cap fixes that problem, and is a direct replacement for stock cap 1.790 inches in diameter. Two per set.

Product Features:
  • Chrome Plated Steel
  • Set of 2 Caps
  • Easy Installation
  • 2 Per Set
See More

Mr. Gasket – Ultra Seal: Harmonic Balancer Bolt/Washer Kit (Part No.7847)

Ultra Seal: Harmonic Balancer Bolt/Washer Kit

from

$38.49
Mr. Gasket Harmonic Balancer Bolt for Ford V8 except 351C. Fits 221,260,289,302,351W small block Windsor engines, 332,352,360,390,406,410,427,428 FEs, and 429,460 385 series big blocks. 5/8-18 x 2 inch long heat treated black oxide coated Grade 8 alloy steel with a thick parallel ground washer to provide accurate, uniform torque.

Product Features:
  • Heat treated black oxide coated Grade 8 alloy steel
  • Thick parallel ground washer provides more accurate, uniform torque
  • Hex Prevents Socket Slippage
  • Accurate And Uniform Torque
  • Black Plated Finish
See More

Edelbrock – Performer RPM Series fuel pump is for 289-351W Ford (Part No.1725)

Performer RPM Series fuel pump is for 289-351W Ford

from

$177.99
Product Features:
  • Mechanical Operation
  • Fuel Sending Unit Not Included
  • For Small-Block 289-351 Ford Engines
  • In Tank Mounting Type
  • 110 GPH
See More

Spectre – Water Neck; Ford 429-460 (Part No.4734)

Water Neck; Ford 429-460

from

$54.99
Spectre’s Ford V8 water neck fits Ford 429 – 460 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes sealing O-ring, and has a 3/8 inch NPT threaded hole for the Ford temp sensor.

Product Features:
  • Fits Ford 429 – 460 engines
  • Has a 3/8 inch NPT threaded hole for temperature sensor
  • Includes sealing O-ring
  • Chrome plated
  • Easy to install
  • Hardware not included
See More

PerTronix – D4062 Flame-Thrower HEI Distributor Rotor Blue (Part No.D4062)

D4062 Flame-Thrower HEI Distributor Rotor Blue

from

$15.99
Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provi

Product Features:
  • PerTronix D4062 Flame-Thrower HEI Distributor Rotor Blue
  • Made from hi-performance 60 KV rated alkyd molding compound.
See More

Mr. Gasket – Super Intake Manifold Bolts (Part No.6082)

Super Intake Manifold Bolts

from

$43.99
Super Intake Manifold Bolts

Competition Cams – Magnum/Marine 253/253 Hydraulic Flat Cam for Ford 429,460 (Part No.34-337-4)

Magnum/Marine 253/253 Hydraulic Flat Cam for Ford 429,460

from

$284.99
An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts. Ideal for use with higher compression ratio engines that

Product Features:
  • Best with aftermarket torque converters and 9.5:1 compression.
  • Great high RPM power.
  • Easy on valve train parts.
  • Can be used with mild ratio rocker arms and traditional performance valve springs.
See More

Mr. Gasket – Valve Cover (Part No.9412)

Valve Cover

from

$87.29
These Mr. Gasket chrome plated stamped steel valve covers have a flat smooth top, and internal baffles. Fits Ford 332,360,390,406,427,428. Sold as a pair.

Product Features:
  • Fits Ford big block (FE series)
  • Chrome plated steel construction
  • Sold as a pair
  • Long Lasting Durability
  • Cadmium Plated To Resist Corrosion
  • Easy Installation
See More

Mr. Gasket – Thermocap Radiator Cap (Part No.2470R)

Thermocap Radiator Cap

from

$48.09
The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:
  • Indicates coolant temperature
  • Helps prevent coolant injuries
  • Fahrenheit and centigrade readings
  • Color-coded temperature ranges
  • Integrated coolant reclamation valve
  • Improves under-hood appearance
  • Chromed crown with a colored trim ring
See More

Spectre – Oil Pan (Part No.5490)

Oil Pan

from

$196.99
Spectre’s Chrome Oil Pans feature a front sump and triple chrome plating. This product is designed to fit Ford passenger cars and 2 wheel drive trucks with 351C, 351M, and 400 engines. This OEM replacement oil pan is manufactured using high quality materials and is engineered for optimum fit and function.

Product Features:
  • Triple chrome-plated
  • Steel construction
  • Front sump
  • OEM replacement.
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1020)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$41.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1419)

Exhaust Manifold Gasket Set

from

$26.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Remote Oil Filter Kit (Part No.7682)

Remote Oil Filter Kit

from

$97.99
This kit relocates the oil filter for quick, clean and easy access and increased filtering. It is complete with precision die cast aluminum by-pass, filter brackets and all high pressure connectors.

Product Features:
  • Relocate oil filter to an easy access location
See More

Competition Cams – XE Computer Controlled 206/212 Hydraulic Roller Cam K-Kit for Ford 5.0L (Part No.K35-512-8)

XE Computer Controlled 206/212 Hydraulic Roller Cam K-Kit for Ford 5.0L

from

$1157.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:
  • Excellent performance in street fuel injected applications.
  • More vacuum allows an increase in duration for improved performance and assists power brakes.
  • Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
  • Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
See More

FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2941)

Engine Crankshaft Seal Kit

from

$48.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • PTFE offers the best in fluid and high-temperature compatibility and contact sealing surface can run on undersize shafts, seal minor imperfections and virtually eliminate shaft wear.
  • Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
  • Not intended for use in emission controlled vehicles.
See More

Popular 1972 Ford Country Squire Performance and Racing Products Categories

1972 Ford Country Squire Performance and Racing Products

You count on your 1972 Ford Country Squire to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 161 Performance and Racing Products ranging in price from $10.99 to $788.99, you’re sure to find everything you need for your 1972 Ford Country Squire.

Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 20 different brands like Accel, Mr. Gasket, and Edelbrock. 1972 Ford Country Squire Performance and Racing Products start as low as $10.99!

One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 1,448 extensive product reviews on 1972 Ford Country Squire Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are Water Neck with 3.8 stars and Ford HEI Distributor, Red Cap, For Ford 289-302 V8 Engines with 4.8 stars.

Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1972 Ford Country Squire below to get started!

Top-Rated Performance and Racing Products Brands For Your 1972 Ford Country Squire

Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1972 Ford Country Squire running right for years to come. In our inventory you’ll find brands like Accel, Mr. Gasket, Edelbrock, and even more.

Popular MSD Ignition Performance and Racing Products

You’ll find popular MSD Ignition brand products across Performance Distributors. All are waiting to get your 1972 Ford Country Squire back on the road. Some of the top-rated MSD Ignition products in these categories are:
Distributor Gear; Ford; 302; Bronze
from $83.39
(1)
Distributor Gear; Ford; 302; Bronze
Performance Distributor Components

Top-Rated Edelbrock Performance and Racing Products


If Edelbrock are what you’re looking for, our inventory holds plenty. We stock Edelbrock brand Performance and Racing Products for your 1972 Ford Country Squire, and some of our most reviewed Edelbrock parts include:

FAQs for 1972 Ford Country Squire Performance and Racing Products

What are the most purchased Performance and Racing Products for the 1972 Ford Country Squire?

Out of 161 Performance and Racing Products for the 1972 Ford Country Squire, the most popular in our inventory are:
High Performance 180 Degree Thermostat for Increased Flow
from $26.99
(20)
High Performance 180 Degree Thermostat for Increased Flow
Performance Engine Coolant Thermostats
Lower Intake Manifold Gasket Set: 11 Piece Set
from $33.99
(4)
Lower Intake Manifold Gasket Set: 11 Piece Set
Performance Engine Intake Manifold Gaskets

What are the top-rated 1972 Ford Country Squire Performance and Racing Products?

Top-rated Performance and Racing Products for your 1972 Ford Country Squire based on customer reviews/ratings are:
Water Neck
from $19.99
(12)
Water Neck
“FINALLY… first time not having to re-do flimsy paper gaskets. Aside from thicker cork gasket, O ring is only way to go !”
Ford HEI Distributor, Red Cap, For Ford 289-302 V8 Engines
from $228.99
(4)
Ford HEI Distributor, Red Cap, For Ford 289-302 V8 Engines
“Like the distributor so much, that I am contemplating on replacing the Mallory Distributor on the other car with one.”
High Perf. Full-Flow Lube Spin-on
from $16.99
(4)
High Perf. Full-Flow Lube Spin-on
“Filter size for my boat. OMC 460. works fine. HP filters have a bypass so that clogs do not cause the engine to starve for oil… important for HP eng”