Faster, Easier Replacement of Clutches. Align clutch plates and pilot bearings accurately. Shaft and bushings provide an accurate fit for eight pilot bearing sizes and the tapered cone handles the rest.
YOU MAY ALSO LIKE
(0)
National
Bearings
(3)
Driveworks
Clutch Release Bearing
(0)
Dorman - Help
Clutch Alignment Tool Splines 23, Outer Diameter 1 In.
(5)
Felpro
REAR MAIN BEARING SEAL SET
(0)
Dorman - Help
Clutch Alignment Tool Splines 26, Outer Diameter 1-1/8 In.
(123)
Pennzoil
Platinum 5W-30 Full Synthetic Motor Oil, 5 Quart
(2)
Dorman - Help
Clutch Alignment Tool Splines 10, Outer Diameter 1-1/16 In.
Brake Parts Cleaner, Non-Chlorinated, High VOC, 14 oz.
Will this work on 2006 Kia Sorento 2 wheel drive? The vin is KNDJD733465620496
Verified Reply - Solomon
Hi Presly, I'm glad to help you! This Lisle Clutch Alignment Tool (Part # 55500) should work fine for your 2006 Kia Sorento, it includes 0.590"-inches, 0.612"-inches, 0.624"-inches, 0.668"-inches, 0.749"-inches, 0.786"-inches, 0.808"-inches and 0.984"-inches adaptors and it is universal and not vehicle specific. You would have to match one by size to what is in your vehicle that can be fabricated into its place.
will this Lisle Clutch Alignment Tool
Part # 55500 work for a 1970 chevy c20 4 speed clutch?
Verified Reply - Solomon
Hi Chris, I'm glad to help you! This Lisle Clutch Alignment Tool (Part # 55500) should work fine for your 1970 Chevrolet C20, it includes 0.590"-inches, 0.612"-inches, 0.624"-inches, 0.668"-inches, 0.749"-inches, 0.786"-inches, 0.808"-inches and 0.984"-inches adaptors and it is universal and not vehicle specific. You would have to match one by size to what is in your vehicle that can be fabricated into its place.
Will this work on a 15 Ford Focus se 1.0 turbo
Verified Reply - Solomon
Hi Ryan, I'm glad to help you! This Lisle Clutch Alignment Tool (Part # 55500) should work fine for your 2015 Ford Focus SE and it is universal and not vehicle specific. You would have to match one by size to what is in your vehicle that can be fabricated into its place.
Will it fit a 2018 Dodge Challenger? Cuz I can't seem to find the clutch alignment tool kit for my 2018 Dodge Challenger
Verified Reply - Solomon
Hi Chris, I'm glad to help you! This Lisle Clutch Alignment Tool (Part # 55500) should work fine for your 2018 Dodge Challenger, it includes 0.590"-inches, 0.612"-inches, 0.624"-inches, 0.668"-inches, 0.749"-inches, 0.786"-inches, 0.808"-inches and 0.984"-inches adaptors and it is universal and not vehicle specific. You would have to match one by size to what is in your vehicle that can be fabricated into its place.
What size are the adaptors?
Verified Reply - Steve
Hi Bruce, I'm glad to assist you! This Lisle Clutch Alignment Tool - Part # 55500 includes 0.590", 0.612", 0.624", 0.668", 0.749", 0.786", 0.808" and 0.984" - inch adaptors.
Displaying Question & Answer 1-5
TOP SELLERS IN THIS CATEGORY
(62)
AutoCraft
Microfiber Glass Cleaning Towels: 12" x 16", 2 Pack
(35)
Rain-X
De-Icer -30 Degree Windshield Washer Fluid
(310)
Valvoline
Non-Chlorinated Low VOC Brake Parts Cleaner (15 oz.)
(1)
Chemical Guys
Complete Car Wash & Clay System for Glass-Smooth Shine
(257)
Carquest Wearever
Brake Parts Cleaner, Chlorinated, Non-Flammable, 19 oz.
(15)
American Grease Stick Co.
Sil-Glyde Brake Lubricant: Silicone, Stops Break Noise, .14 Oz (sold by each)
(645)
Lucas Oil Products
Lucas Upper Cylinder Lube/Fuel Treatment - 5.25 oz
(1010)
Scott Brand
Shop Towels: 9.4" x 11" Sheets, 55 Sheets a Roll, 1 Pack
(37)
AutoCraft
Ultimate Wheel and Tire Scrubber with Stiff Bristles for Enhanced Cleaning