CARDONE Remanufactured Rack & Pinions are re-engineered, built and tested to meet or exceed O.E. fit and performance. 100% new, O.E.-style o-rings and seals are installed to ensure leak-free, long-lasting performance. A final protective coating is applied and each unit is tested to guarantee a perfect fit and function.
Product Features:
Protective coating applied to each unit to extend the life of the unit (where applicable).
100% performance testing to ensure perfect fit, function and reliable performance.
100% hydraulic testing for proper flow, leakage and performance ensures perfect fit and function (where applicable).
Racks are surfaced to precise specifications to prevent leaking between chambers and extend unit life.
100% new O.E.- style o-rings and lip seals ensure leak-free and long-lasting performance (where applicable).
All new spool valve seals and rack donut seals are installed to eliminate internal leaks and ensure reliable performance (where applicable).
Valve housings have polished micro-finish sleeves for durability (where applicable).
As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%.
Specifications
Bellows Color:
Black
End To End Length:
45.437 in
Gasket Or Seal Included:
Yes
Grade Type:
Regular
Inlet Line Fitting Diameter:
17.83 mm
Inlet Line Fitting Gender:
Male
Inner Tie Rods Included:
Yes
Installation Hardware Included:
Yes
Mounting Brackets Included:
No
Mounting Hardware Included:
Yes
Mounting Hole Quantity:
2
Outer Tie Rods Included:
No
Outlet Line Fitting Diameter:
11.66 mm
Outlet Line Fitting Gender:
Male
Package Contents:
Rack and Pinion; Mounting Bushing; Sealing Kit; Instruction Sheet
Steering Input Shaft Diameter:
16.78 mm
Steering Rack Color/Finish:
Black
Total Turns Lock To Lock:
2.875
Type:
Hydraulic
YOU MAY ALSO LIKE
(56)
Carquest Standard Brake Pads: Reliable and Dependable Stopping
Driveworks Wheel Bearing and Hub Assembly: 5 Studs
(450)
TRICO Rear Rear 14'' Wiper Blade: Clear Rear Visibility In All Conditions
(1)
NGK Ignition Coil: Meets or Exceeds Original Equipment Specifications, 1 Piece
(21)
Carquest Premium Standard Thermostat: 180 Degrees
(2115)
Mobil 1 Oil Filter: Ideal for Synthetic Oil, Protection To 20,000 Miles
(8)
Dorman Standard Engine Oil Drain Plug: M14-1.50 Thread, 17 mm Head, 1 Pack
(260)
Carquest Brake Cleaner Brake Parts Cleaner, Chlorinated, Non-Flammable, 19 oz.
(0)
Dorman Evaporative Emissions Canister Vent Valve
3.1 out of 5
10 Customer Reviews
50%of respondents would recommend this to a friend
Ratings Distribution
5 Stars
4
4 Stars
1
3 Stars
1
2 Stars
0
1 Star
4
Pros
1
Durable
1
Lightweight
1
Hr and half install time
1
Clean
1
Good Instructions
Cons
1
Difficult To Install
1
Do Not Last
Best Uses
1
Small Cars
1
Everyday Driving
1
Replacement
Car/Motorcycle Describe yourself
3
Casual Driver
2
Mechanic
1
Auto Enthusiast
Most Liked Positive Review
Great service from Advance
Takes several hours to remove,then several hours to install. take your time, take pictures as you remove parts, so you can install in reverse order. keep all parts and tools clean will make it easier to install. parts was well rebuilt, had lot of check marks on fittings and pipes so you know they have been checked. count the turns on rod-ends so you can be sure to put back them same to keep it close before getting lined back up. use lots of safety when you jack up car. use several jack stands and wood blocks. use real good jack to lower sub-frame about 3 inches to get access to sway bar bolts. be sure to fluse all old old out of pump and hoses.
Most Liked Negative Review
Third time the charm... God I hope so!
This will be the third rack and pinion in so many years. I installed the last one in late November, I put in a new PS pump as well as new hoses. I boiled the reservoir spotless and let it dry over night I then ran air through the reservoir till there was absolutely no water in it anywhere. I then ran the fluid through a filter for a half hour just looping from one end of the pump to the other before finally connecting the new lines to the new rack and pinion. I then followed the instructions on the Cardone site as well as the directions that came with the unit as to purging the air from the new system. Yet here it is three months after my last PS replacement and I have to do it all over again!!! Can't anyone make decent parts anymore? The last battery and two different alternators I bought from Advance were junk right out of the box as well and took several trips back to the store to get functioning ones.
Will this fit a 2004 chevorlet classic fwd, 2.2L I4?
Verified Reply - Solomon
Hi Jonah , I'm glad to help you! This Cardone Hydraulic Power Rack and Pinion {Complete} - Domestic (Part #22-184) is an exact fit for a 2004 Chevorlet Classic.
Will this fit a 2003 Toyota Tacoma Prerunner, 2wd, 3.4L v6?
Verified Reply - Solomon
No, Vitaliy! This Cardone Hydraulic Power Rack and Pinion (Part No. 22-184) does not fit your 2003 Toyota Tacoma. We do have an exact fit hydraulic power rack and pinion available online for your vehicle and the part number is 26-1611. Please enter your vehicle on our website and search for this part to check the fitment.
Will this work with my existing item ? Even it has vari effort steering !
Verified Reply - Vincent
This Fenco Rack and Pinion - part# RP6514 is vehicle specific. For assisting you further, please provide the year, make, model and engine size of the vehicle. For any further assistance, you may also visit your nearest Advance Auto store or call us directly at 1-877-ADVANCE (238-2623) and one of our representatives there would be more than happy to assist you.
how does this product get bolted do
Open Reply - Parts Guru Geo
I recommend purchasing a Haynes repair manual specifically for your vehicle. This should be able to assist you further into detail on how to repair or replace specific parts.