Mitsubishi Flywheels and Flexplates

Vehicles with automatic transmissions have a flex plate. The flex plates connects the engine and transmission. Most flex plates are made of a thick piece of sheet metal with bolt holes for the torque converter and teeth for the starter. The job of a flex plate is to allow for expansion of the torque converter as engine RPM increases. The constant expansion and contraction of a flex plate over time can result cracks and/or shearing of the flex plate. A damaged flex plate can create serious (expensive) damage. Broken flex plates can not be repaired, they must be replaced. ATP flex plates are made of high quality steel and contain the correct bolt hole spacing and ring gear teeth just like the original part to ensure long life and durability

Product Features:

• Balanced to factory specs
• Fit and function like the original parts
• Restores normal operation

LuK: New flywheels are a smart alternative! The flywheel is an integral part of clutch replacement. It must provide a smooth, flat surface for proper clutch operation. Pairing your clutch set with a new flywheel is a smart, cost-effective alternative to resurfacing. All new – never remanufactured – every component is engineered and manufactured to OE specifications, including ring gear and dowel pins.

LuK: New flywheels are a smart alternative! The flywheel is an integral part of clutch replacement. It must provide a smooth, flat surface for proper clutch operation. Pairing your clutch set with a new flywheel is a smart, cost-effective alternative to resurfacing. All new – never remanufactured – every component is engineered and manufactured to OE specifications, including ring gear and dowel pins.

LuK: New flywheels are a smart alternative! The flywheel is an integral part of clutch replacement. It must provide a smooth, flat surface for proper clutch operation. Pairing your clutch set with a new flywheel is a smart, cost-effective alternative to resurfacing. All new – never remanufactured – every component is engineered and manufactured to OE specifications, including ring gear and dowel pins.

LuK: New flywheels are a smart alternative! The flywheel is an integral part of clutch replacement. It must provide a smooth, flat surface for proper clutch operation. Pairing your clutch set with a new LuK flywheel is a smart, cost-effective alternative to resurfacing. All new – never remanufactured – every component is engineered and manufactured to OE specifications, including ring gear and dowel pins.

LuK conventional flywheels are dynamically balanced to reduce vibration and improve clutch performance. All new – never remanufactured – every flywheel component is engineered and built to original-equipment specifications, including the ring gear and dowel pins.

Product Features:

• OE quality and direct fit application
• Made from high quality steel
• Designed to reduce clutch chatter and vibration
• Dynamically balanced

LuK conventional flywheels are dynamically balanced to reduce vibration and improve clutch performance. All new – never remanufactured – every flywheel component is engineered and built to original-equipment specifications, including the ring gear and dowel pins.

Product Features:

• OE quality and direct fit application
• Made from high quality steel
• Designed to reduce clutch chatter and vibration
• Dynamically balanced

LuK: New flywheels are a smart alternative! The flywheel is an integral part of clutch replacement. It must provide a smooth, flat surface for proper clutch operation. Pairing your clutch set with a new flywheel is a smart, cost-effective alternative to

LuK: New flywheels are a smart alternative! The flywheel is an integral part of clutch replacement. It must provide a smooth, flat surface for proper clutch operation. Pairing your clutch set with a new flywheel is a smart, cost-effective alternative to resurfacing. All new – never remanufactured – every component is engineered and manufactured to OE specifications, including ring gear and dowel pins.

LuK: New flywheels are a smart alternative! The flywheel is an integral part of clutch replacement. It must provide a smooth, flat surface for proper clutch operation. Pairing your clutch set with a new flywheel is a smart, cost-effective alternative to resurfacing. All new – never remanufactured – every component is engineered and manufactured to OE specifications, including ring gear and dowel pins.

EXEDY Racing Flywheels are made from solid one piece billet chromoly steel forging. They are specifically designed to reduce weight and inertia for better engine response. Most incorporate special design features to enhance air flow to improve the cooling of the clutch. The ring gear teeth are milled onto the flywheel unlike an aluminum flywheel where the ring gear is pressed onto the flywheel and have the possibility of separating from the flywheel.

Product Features:

• The flywheels are made from solid one piece billet chromoly steel or chromoly steel forging
• Exedy steel billet and forged steel flywheels have passed engineering tests to 15000-18000 rpm
• The ring gear and teeth are integrated onto the flywheel unlike an aluminum flywheel where the ring gear is pressed onto the flywheel and has the possibility of separating
• They are specifically designed to reduce weight and inertia for better engine response
• Most incorporate special design features to enhance airflow which improves the cooling of the clutch

LuK dual-mass flywheels absorb engine vibrations before they are transmitted to the driveline where they can create gear rattle. These units feature a built-in damper designed to isolate engine torque spikes and prevent transmission damage. By design, dual-mass flywheels cannot be resurfaced. This all makes the LuK dual mass flywheel the ideal solution. With one drawback: the higher the mass reactance of the vibrating masses, the more excessive the resonance increase and associated torque peaks. With the dual mass flywheel, this would be easily perceived when starting and stopping the engine; much more easily than with a conventional clutch system. Additionally: the smaller flymass of the engine has less of a stabilizing effect on the speed fluctuation of the engine. Thanks to decades of experience in clutch building, the LuK specialists were able to find an excellent solution to this problem. An additional damping device effectively prevents resonance overload. In normal operation, however, this additional damping device has no function and the torsional vibrations of the engine are filtered out by spring dampers. Friction and spring rate – the correct ratio is important. For optimal vibration isolation and soft resonance passage when starting and stopping the engine, the ratio between friction and spring rate must be optimal. The length of the springs is a key factor: The softer a spring, the more efficiently vibrations are isolated. The extra-long springs of the latest generation of dual mass flywheels significantly reduce the spring rate compared to a first generation dual mass flywheel. In routine driving operations, excessive resonance increases are kept almost completely away from the gearbox.

Product Features:

• Top driving comfort
• Absorbs vibrations
• Prevents noise
• Enables comfortable, low-revs driving
• Saves fuel
• Relieves crankshaft and gearbox

EXEDY Racing Flywheels are made from solid one piece billet chromoly steel forging. They are specifically designed to reduce weight and inertia for better engine response. Most incorporate special design features to enhance air flow to improve the cooling of the clutch. The ring gear teeth are milled onto the flywheel unlike an aluminum flywheel where the ring gear is pressed onto the flywheel and have the possibility of separating from the flywheel.

Product Features:

• The flywheels are made from solid one piece billet chromoly steel or chromoly steel forging
• Exedy steel billet and forged steel flywheels have passed engineering tests to 15000-18000 rpm
• The ring gear and teeth are integrated onto the flywheel unlike an aluminum flywheel where the ring gear is pressed onto the flywheel and has the possibility of separating
• They are specifically designed to reduce weight and inertia for better engine response
• Most incorporate special design features to enhance airflow which improves the cooling of the clutch

LuK: Don’t gamble – stay with the original DMF! The DMF prevents damages solid flywheels may cause. The Dual Mass Flywheel (DMF) is individually fine-tuned for every type of car. The risks of using solid flywheels are numerous – from increased wear of

LuK conventional flywheels are dynamically balanced to reduce vibration and improve clutch performance. All new – never remanufactured – every flywheel component is engineered and built to original-equipment specifications, including the ring gear and dowel pins.

Product Features:

• OE quality and direct fit application
• Made from high quality steel
• Designed to reduce clutch chatter and vibration
• Dynamically balanced

LuK: New flywheels are a smart alternative! The flywheel is an integral part of clutch replacement. It must provide a smooth, flat surface for proper clutch operation. Pairing your clutch set with a new LuK flywheel is a smart, cost-effective alternative

LuK conventional flywheels are dynamically balanced to reduce vibration and improve clutch performance. All new – never remanufactured – every flywheel component is engineered and built to original-equipment specifications, including the ring gear and dowel pins.

Product Features:

• OE quality and direct fit application
• Made from high quality steel
• Designed to reduce clutch chatter and vibration
• Dynamically balanced

LuK: New flywheels are a smart alternative! The flywheel is an integral part of clutch replacement. It must provide a smooth, flat surface for proper clutch operation. Pairing your clutch set with a new flywheel is a smart, cost-effective alternative to

LuK conventional flywheels are dynamically balanced to reduce vibration and improve clutch performance. All new – never remanufactured – every flywheel component is engineered and built to original-equipment specifications, including the ring gear and dowel pins.

Product Features:

• OE quality and direct fit application
• Made from high quality steel
• Designed to reduce clutch chatter and vibration
• Dynamically balanced

LuK conventional flywheels are dynamically balanced to reduce vibration and improve clutch performance. All new – never remanufactured – every flywheel component is engineered and built to original-equipment specifications, including the ring gear and dowel pins.

Product Features:

• OE quality and direct fit application
• Made from high quality steel
• Designed to reduce clutch chatter and vibration
• Dynamically balanced

LuK: New flywheels are a smart alternative! The flywheel is an integral part of clutch replacement. It must provide a smooth, flat surface for proper clutch operation. Pairing your clutch set with a new flywheel is a smart, cost-effective alternative to resurfacing. All new – never remanufactured – every component is engineered and manufactured to OE specifications, including ring gear and dowel pins.

AT FLEX PLATE