Lincoln Mark VII Fluids and Chemicals

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• Maxlife technology prevents engine breakdown with 40% better wear protection than the industry standard
• Refresh aging seals and prevent leaks with seal conditioners
• Reduce sludge, deposits, corrosion, and rust with added detergents – keep motors clean inside
• Enhanced friction performance helps maximize power with advanced friction-fighting agents
• Meets or exceeds all requirements of ilsac gf-6a, api sp, api sn with sn plus, api sn
• MaxLife High Mileage Synthetic Blend Engine Oil is specially designed for engines with over 75,000 miles, providing greater protection and maximizing engine life.

Special Tec LL 5W-30 Full Synthetic Engine Oil is engineered to deliver exceptional performance and long-lasting engine protection for both gasoline and diesel vehicles without particulate filters. This premium, fully synthetic oil is designed to meet and exceed the stringent requirements of major manufacturers, making it ideal for modern engines equipped with turbochargers and catalytic converters. With its high lubrication reliability, outstanding engine cleanliness, and optimum stability to aging, this oil ensures your engine runs smoothly under all conditions. Its advanced formulation helps keep oil consumption low while supporting extended oil change intervals as recommended by your vehicle’s manufacturer. Made in Germany, this SAE 5W-30 oil offers superior all-season performance, ensuring your engine stays protected and efficient year-round.

Product Features:

Product Features:
• ideal with turbochargers and catalytic converters
• high lubrication reliability
• outstanding engine cleanliness
• optimum stability to aging
• Keep oil consumption low
• Made in germany

Valvoline MaxLife Multi-Vehicle ATF is a full-synthetic formulation with advanced additives to prevent the major causes of transmission breakdown and help extend transmission life.  Developed to help prevent leaks, maximize transmission performance, reduce transmission wear, and maintain smooth shifting longer than conventional fluids. It is suitable for use in a broad range of ATF applications including most Ford, GM, Toyota, Honda, Nissan, Hyundai, BMW, Mercedes, Volvo, VW & Audi. Recommended for use in the following applications: GM DEXRON-II, DEXRON-III, DEXRON-VI, Ford MERCON LV, Toyota/Lexus Type T, T-II, T-IV, WS, Honda/Acura, ATF-Z1, Nissan/Infiniti Matic-D, Matic-J, Matric-K, Matic-S, Hyundai/Kia SP-II, SP-III, SP-IV, SPH-IV, BMW 7045E, ETL 8072B, LA2634, LT71141, Allison C-4, Mercedes Benz NAG-1, Volvo 1161521, 1161540, 97340, 1273.41, and VW/Audi G-052-025-A2, G-052-162-A1. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.

Product Features:

• Formulated with full-synthetic base oils and long life friction modifiers to help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
• High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks in high mileage transmissions
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Valvoline Full Synthetic MaxLife Multi-Vehicle ATF, the No. 1 ATF product, suitable for use in 95% of vehicles. And now, it’s recommended for most belt & chain-driven continuously variable transmissions (CVT). Featuring advanced additives to prevent the major causes of transmission breakdown, it’s designed to help prevent leaks, reduce wear & tear, and maximize performance. Has improved thermal stability for longer fluid life, better viscosity stability for consistent transmission operation, and frictional enhancements for smooth gear engagements. Valv MaxLife Multi-Vehicle ATF is suitable for most Ford, GM, Toyota, Honda, Nissan, Hyundai, Subaru, BMW, Mercedes, Volvo, VW & Audi vehicles. Recommended for use in: GM DEXRON-II, DEXRON-III, DEXRON-VI, and DEX-CVT; Ford MERCON LV; Toyota/Lexus Type T, T-II, T-IV, WS, CVTF FE, and CVTF TC; Honda/Acura ATF-Z1 and Honda CVT; Nissan/Infiniti Matic-D, Matic-J, Matic-K and Matic-S; Hyundai/Kia SP-II, SP-III, SP-IV and SPH-IV; BMW 7045E, ETL 8072B, LA2634 and LT71141; Allison C-4; Mercedes-Benz NAG-1; Volvo 1161521, 1161540, 97340 and 1273.41; Subaru ATF HP, Lineartronic chain CVT and CVT-II, Lineartronic High Torque CVT, and CV-30; and VW/Audi G-052-025-A2 and G-052-162-A1. CURRENTLY UNABLE TO SHIP THIS PRODUCT TO CUSTOMERS LOCATED IN CALIFORNIA

Product Features:

• FOR USE IN 95% OF VEHICLES INCLUDING MOST CVTs in operation with US registered light duty applications
• HIGH PERFORMANCE CONDITIONING AGENTS prolong seal elasticity to prevent leaks
• IMPROVED DURABILITY & TRANSMISSION LIFE with anti-wear technology to avoid costly repairs
• ENHANCED HIGH & LOW TEMP PERFORMANCE supports transmission fluid in all weather situations

FRAM Extended Life AMAM Concentrate is compatible with any antifreeze/coolant in any vehicle with aluminum or other cooling system metals. The formulas have a blend of long-lasting inhibitors to guard against temperature extremes and the effects of rust, corrosion, and premature water pump failure. FRAM Concentrate meets or exceeds ASTM D3306 and D4985 for corrosion protection for cars and light duty trucks, while providing reliable freeze-up and boil-over protection.

Product Features:

• Formulated to work with All Vehicles. Works with all fluid colors; All OAT, POAT, HOAT and IAT.
• Longer Engine Life Guarantee – 5 year/150,000 mile Extended life formula.
• Includes patented technology, the best advancement in cooling system parts protection that protects against rust and corrosion of all cooling system metals, including aluminum. Protection for 150,000 miles.
• Concentrate formula. Must mix with distilled to the desired mix ratio of EG and water. Can be used for top-off, complete drain and refill or flush and refill of the cooling system.

FRAM Extended Life AMAM 50/50 is compatible with any antifreeze/coolant in any vehicle with aluminum or other cooling system metals. The formulas have a blend of long-lasting inhibitors to guard against temperature extremes and the effects of rust, corrosion, and premature water pump failure. Top-off your cooling system with FRAM Extended Life AMAM 50/50, which is a blend of 50% antifreeze and 50% demineralized water. FRAM 50/50 meets or exceeds ASTM D3306 and D4985 for corrosion protection for cars and light duty trucks, while providing reliable freeze-up and boil-over protection.

Product Features:

• Formulated to work with All Vehicles. Universally works with all fluid colors; All OAT, POAT, HOAT and IAT
• 5 year/150,000 mile Extended life formula.
• Meets or exceeds ASTM D3306 and D4985 for corrosion protection.
• Ready to Use formula (prediluted to a 50% Eg and 50% distilled water mix). Perfect for small volume top-off or complete drain and refill of the cooling system

Antifreeze Conventional Green 50/50 is an ethylene glycol-based product for use in car and light duty trucks that are already using a conventional coolant. The inhibitors prevent rust, corrosion, and provide freeze-up and boil-over protection. Prime Green 50/50 can be used to top-off cooling systems in vehicles using conventional AF/C, will not harm rubber parts, and meets ASTM D3306 and D4985 standards.

Product Features:

• Low Silicate Formula.
• When used as directed, will provide protection for a minimum of 1 year
• Meets or exceeds ASTM requirements for cars, light duty trucks
• Ready to Use formula (prediluted to a 50% Eg & 50% distilled water mix). Perfect for small volume top-off or complete drain and refill of the cooling system

Product Features:

• Reduces heat & wear
• Eliminates TQ converter shudder & clutch pack chatter
• For all automatic transmissions & 4×4 transfer cases

Liqui Moly’s Leichtlauf High Tech 5W-40 is a fully synthetic, premium low-friction engine oil for all-season use in gasoline and diesel engines without diesel particulate filters (DPF). The combination of innovative base oils – based on synthesis technology and the latest additive technology – guarantees an engine oil that reduces oil and fuel consumption and that ensures fast lubrication of the engine. Depending on the manufacturer instructions, oil change intervals of up to 40,000 km are possible. Ideally suited for modern gasoline and diesel engines with multi-valve technology, turbocharger and with or without charge air cooling. Especially suitable where there are long intervals between changes and heavy duty engine requirements.

Product Features:

• All season use reliable at high and low temperatures
• Suited for modern gasoline and diesel engines with multivalve technology, turbocharger and with or without charge air cooling
• An engine oil that reduces oil and fuel consumption
• Ensures fast lubrication of the engine
• Made in germany
• Full Synthetic Oil Composition

Upgrading your motor oil to Valvoline Full Synthetic High Mileage with MaxLife Technology can help you increase the longevity of your car, truck or SUV with over 75,000 miles. It’s proven to protect your high-mileage motor against wear, friction, heat, and deposits – the leading causes of engine breakdown and expensive repairs. Our exclusive formulation goes beyond industry standards to protect your engine. It’s fortified with enhanced wear additives and friction-fighting agents to safeguard critical engine components, extra detergents to clean inside your engine, and premium seal conditioners to restore aging seals and prevent leaks. Superior viscosity modifiers and high-quality base oils help it perform exceptionally in both high and low temperatures. Engineered with ingenuity, tested with tenacity, and proven with purpose, our formula was innovated in America with a century and a half of hands-on experience from the original motor oil brand.

Product Features:

• Enhanced maxlife technology prevents engine breakdown in extreme conditions with 50% better wear protection than the industry standard
• Treat and prevent leaks with premium seal conditioners to keep oil out of places it shouldn’t be
• 25% extra defense against deposits, sludge, corrosion and rust via interior-cleansing detergents
• Extreme temperature protection through our high-quality base oils and superior viscosity modifiers
• Meets or exceeds all requirements of ilsac gf-6a, api sp, api sn with sn plus, api sn
• High Mileage Protection: Valvoline Full Synthetic High Mileage Engine Oil is specially designed to protect engines with over 75,000 miles against wear, friction, heat, and deposits, ensuring a longer lifespan for your vehicle.

All-year oil for gasoline and diesel engines. Modern multi-purpose low-friction motor oil developed according to the latest technology. Unconventional base oils based on HC synthetic technology were combined with the most modern additive technology. The low-viscosity and high sheer stability of the motor oil guarantees optimal cleanliness, reduces frictional loss in the engine and provides outstanding protection against wear. The results are savings in fuel and an extended service life for the engine. Tested for turbochargers and catalytic converters.

Product Features:

• High-tech low-viscosity engine oil
• Advance wear protection formula
• Fastest cold start oiling during start up
• Provides ideal oil pressure under all operating conditions
• Keep oil consumption low
• Made in germany

FRAM Mercon V ATF is for use in Ford vehicle transmissions and transaxles. Especially formulated to exhibit better low-temperature flow and better shear-stability, FRAM Mercon V ATF meets Ford performance requirements of vehicles specifying Mercon V ATF. FRAM Mercon V ATF is recommended for use in all transmissions, hydraulic systems, and power steering units manufactured by American, European, Korean, Japanese and other manufactures from around the world specifying Mercon V type transmission fluids.

Product Features:

• Improved foam and corrosion prevention
• Improved oxidation stability
• Promotes smooth shifting
• Always Refer To Your Vehicles Operating Manual To Select The Correct Grade Oil For Your Transmission
• Transmission Fluids Also Applicable In Power Steering Units; Check Owners’ Manual

Prestone MAX American Vehicles Power Steering Fluid (PSF) + Stop Leak maximizes and increases system life + the power to stop leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. This formula is also great at preventing leaks by rejuvenating seals before they leak. This synthetic fluid is designed with 2X Anti-wear System Protection, which means more protection against pump failure, squeals and clogs. 100,000 mile fluid life, 2X more than conventional fluid, extends the time between replacement. This fluid is formulated for American vehicle manufacturers: Ford, Lincoln, Mercury, Dodge, Ram, Jeep, Chrysler, GMC, Chevrolet, Buick, Cadillac, Pontiac, Oldsmobile and others. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 100,000 Mile Fluid Life. Synthetic Formula for longer life and more protection
• MAX + Stop Leak. Stop Leak Additives to prevent and stop power steering system leaks.
• For use in American vehicle manufacturers: Ford, Lincoln, Mercury, Dodge, Ram, Jeep, Chrysler, GMC, Chevrolet, Buick, Cadillac, Pontiac, Oldsmobile and other
• 2X Anti-Wear Protection for enhanced System Life vs. conventional fluid. More protection against pump failure, squeals and clogs

Valvoline Import Multi-Vehicle Automatic Transmission Fluid is specifically formulated for use in most Toyota, Nissan, Honda and other imported vehicles. It is formulated with all synthetic base stocks and a proprietary additive system to ensure optimal transmission performance in a wide variety of vehicles. Valvoline Import Multi-Vehicle ATF can also be used in many domestic vehicles. It meets requirements of General Motors and Ford vehicles. Recommended for use in the following applications: Ford MERCON, GM DEXRON-II and DEXRON-III, BMW LT 71141 and ETL-7045E, Nissan/Infiniti Nissan ATF, Matic-D, Matic-K and Matic-J, Mitsubishi Diamond SP-II and SP-III, Subaru ATF-HP, Hyundai/ KIA SP-II and SP-III, Toyota/Lexus Type T, T-III and T-IV, Honda/Acura ATF-Z1 (except in CVTs), Mercedes Benz NAG1, Volvo passenger car (except AW-1), and Volkswagen/Audi TL52162. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.

Product Features:

• Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Prestone Power Steering Fluid + Stop Leak (PSF+SL) delivers increased system life and prevents and stops system leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. The stop leak additives also prevent leaks by rejuvenating seals before they leak. Also designed with Anti-wear System Protection, Prestone PSF+SL protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 50,000 Mile Fluid Life
• Includes Stop Leak Additives to prevent and stop power steering system leaks.
• Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber and gasket components.
• Conventional Formula – For use in all manufacturers

Prestone Power Steering Fluid + Stop Leak (PSF+SL) delivers increased system life and prevents and stops system leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. The stop leak additives also prevent leaks by rejuvenating seals before they leak. Also designed with Anti-wear System Protection, Prestone PSF+SL protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 50,000 Mile Fluid Life
• Includes Stop Leak Additives to prevent and stop power steering system leaks.
• Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber and gasket components.
• Conventional Formula – For use in all manufacturers

Prestone® DOT 3 Motor Vehicle Brake Fluid delivers enhanced performance vs. DOT standards, benefitting all vehicles calling for DOT 3. This synthetic fluid starts with a higher dry boiling point than the DOT minimum standard to protect against overheating, brake fade and performance decline due to water absorption. This extended life (50,000 mile) fluid is also formulated to prevent corrosion of all metals within the braking system. This formula is safe to use in all DOT 3 braking systems (ABS, disc or drum) and can mix with any DOT 3 fluid. It is recommended to only use the DOT fluid specified for your car, as using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 50,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with High Grade Formula (1)
• Protects against performance decline due to water absorption. Prevents corrosion of all metals within the braking system
• Synthetic, Extended Fluid Life Formula

Prestone DOT 3 Motor Vehicle Brake delivers enhanced performance vs. DOT standards, benefitting all vehicles calling for DOT 3. This synthetic fluid starts with a higher dry boiling point than the DOT minimum standard to protect against overheating, brake fade and performance decline due to water absorption. This extended life (50,000 mile) fluid is also formulated to prevent corrosion of all metals within the braking system.  This formula is safe to use in all DOT 3 braking systems (ABS, disc or drum) and can mix with any DOT 3 fluid.  It is recommended to only use the DOT fluid specified for your car, as using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 50,000 Mile Fluid Life
• Prevent Overheating and Brake Fade with High Grade Formula
• Protects against performance decline due to water absorption. Prevents corrosion of all metals within the braking system.
• Synthetic, Extended Fluid Life Formula

Prestone DOT 3 Motor Vehicle Brake Fluid delivers enhanced performance vs. DOT standards, benefitting all vehicles calling for DOT 3. This synthetic fluid starts with a higher dry boiling point than the DOT minimum standard to protect against overheating, brake fade and performance decline due to water absorption. This extended life (50,000 mile) fluid is also formulated to prevent corrosion of all metals within the braking system.  This formula is safe to use in all DOT 3 braking systems (ABS, disc or drum) and can mix with any DOT 3 fluid.  It is recommended to only use the DOT fluid specified for your car, as using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 50,000 Mile Fluid Life
• Prevent Overheating and Brake Fade with High Grade Formula
• Protects against performance decline due to water absorption. Prevents corrosion of all metals within the braking system.
• Synthetic, Extended Fluid Life Formula

Prestone MAX DOT 3 Motor Vehicle Brake Fluid is our highest grade formula, maximizing performance vs. DOT standard. Prestone MAX is our best brake fluid at protecting against overheating and brake fade. With 100,000 mile fluid life, our longest life fluid has 2X more miles between replacement than regular Prestone DOT 3. Prestone MAX has superior performance in severe braking conditions when compared to regular Prestone DOT 3, which means even more piece of mind about the braking system. This synthetic fluid starts with our highest dry boiling point giving our best protection against performance decline due to water absorption. Prestone MAX DOT 3 is safe to use in all DOT 3 braking systems, ABS, disc or drum, and can mix with any DOT 3 fluid. Mixing Prestone MAX with other fluids will lower the performance rating for miles and boil points, for best results replace completely with Prestone MAX DOT 3. It is recommended to only use the DOT fluid specified for your car. Using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 100,000 Mile Fluid Life
• Prevent Overheating and Brake Fade with Our Highest Grade Formula. Prevents corrosion of all metals within the braking system.
• Superior Protection in Extreme Braking Conditions
• Synthetic, Long Life Formula – 2X Longer than regular Prestone DOT 3

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 in

Product Features:

• Fits Ford 7.5″
• 28 spline
• 4-spring, clutch style positraction
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA