from

$439.99

The B&M Quicksilver features a ratcheting action for positive shifts, Chrome Knob, neutral safety switch, NHRA/IHRA approved Reverse Lockout. Fits Most 3 and 4 speeds.

Product Features:

Universal Floor Mount Application
Base Trimmed For Custom Fit
Cable Operated
Quick Installation
Accurate Shifting

from

$48.49

This unit permits a seamless wide range of adjustment to both amount and rate of ignition advance. This unit helps increase horsepower and throttle response. It provides maximum spark advance while preventing detonation or “pinging”. This kit includes an allen wrench for easy adjustment along with instructions.

Product Features:

Adjustable Vacuum Advance
Increases Horsepower And Throttle Response
Includes Allen Wrench For Adjustments
Instantly Increase Horsepower
Maximum Possible Spark Advance
Not Legal For Sale/Use In CA

from

$10.49

This chrome plated breather, embossed with a Mr. Gasket logo, is perfect for race car vacuum balance systems and OEM use. It fits any 1 1/4 inch diameter hole. It has metal baffle/foam element with 1 inch outer diameter neck and 5/8 inch outer diameter breather tube.

Product Features:

Internally battled
High-porosity filter
Ideal for high performance
Includes rubber grommet

from

$43.99

Fits Chevy small block 265-400 CID, Chevy big block 396-454 CID, & 90 degree Chevy V6. The Starter Motor Heat Shield is built with heat-resistant material sandwiched between two aluminum plates. The shield protects the starter from heat buildup from the exhaust system, especially important when using headers.

Product Features:

Designed to prevent starter overheat due to extreme exhaust temperature
Heat resistant material sandwiched between 2 aluminum plates
Protects Starter From High Temperatures
Made Of 2 Sheets Of Aluminum Heat Resistant Center
Natural Finish

from

$306.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$41.99

Made of high quality stainless steel. These bolts will brighten up your hot rod, or improve the looks of your race car.

Product Features:

Bright Ball Burnish Finish
Made From 304 Stainless
Compact Hex Head Is Ideal Where Space Is Limited
12 Per Set
Resist corrosion and provides a clean professional appearance

from

$9.99

Add sparkle to your engine with this chromed hold-down clamp. With bolt and gasket. Serrations on the bottom prevent distributor and magneto rotation for accurate timing.

Product Features:

Rolled Edges For Strength
Ideal For Magnetos
Ideal For Ignition Distributor

from

$30.19

With the introduction of our 20 Amp extreme HEI module, we needed an HEI cap and rotor that could withstand the high output. The answer was to mold our own HEI cap, rotor and coil cover. The cap and rotor will fit our HEI Pro-Billet distributor, PN 8365, plus will work on stock applications.

Product Features:

Extreme output rotor

from

$350.99

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

from

$620.99

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

Vibratory Polished For Good Looks
Optimized Street Calibration That Works Out Of The Box
Factory Preset Electric Choke For Easy Startups
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
No Unnecessary Trips Back To The Parts Store
Limited Lifetime Warranty
100% Wet Flow Tested By Holley Technicians
Arrives Ready To Run

from

$30.49

Product Features:

Service Part
Makes Connections Quick And Easy

from

$57.99

Available in various sizes, heights, and finishes, Spectre offers a wide variety of high performance valve covers designed to easily replace your stock covers. Designed for 1958-1986 Chevrolet Small Block 265-400 engines, this valve cover features chrome-plated steel construction and a smooth design. Sold in pairs, this stock profile cover is baffled to provide optimum function. With show quality construction and a sealing edge designed for an ideal fit, our valve covers are engineered to look great for applications ranging from custom builds to replacing stock equipment.

Product Features:

Designed for 1958-1986 Chevrolet Small Block 265-400 engines
Baffled for breather system compatibility
Sold in pairs
Triple chrome-plated steel construction
Stock height
Features OEM style sealing edge

from

$461.99

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:

6.25 in. Diameter
Absolutely the most accurate way to trigger the ignition.
The non-magnetic pickup cannot be false triggered.
Powerful magnets are embedded in a billet aluminum trigger wheel.

from

$32.09

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

Features 12-point Smaller-than-standard Bolt Head
Thick Flat Washers Distribute Optimum Clamp Load
Ideal Use Where Space Is Minimal On Race Manifolds
Bolts And Washers Zinc Plated For Protection
Zinc Plated For Protection

from

$15.99

Bolts on with existing timing cover bolts. It is chrome plated steel, which makes is a better compliment to a chrome timing cover. It also has an adjustable red timing pointer. This allows for better visibility and helps you set your timing more easily. Just loosen the screw, set the pointer to the desired initial timing level, and screw it back down. Then you’ll be able to more clearly see if your timing is where you want it when checking your timing.

Product Features:

Bolts on using existing timing cover bolts
Chrome finish compliments chrome timing covers
Red adjustable pointer makes it easier to check timing

from

$37.69

Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Manufactured from high-temperature steel core/graphite faced exhaust material
Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
Conforms to and seals minor surface irregularities
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use
Anti-Stick Properties
Easy Removal For Disassembly

from

$148.99

Constructed of thicker than stock steel plate to withstand the stress of high stall speed converters and high RPM engine. Zinc dichromate plated to resist rust and corrosion. Meets SFI specification 29.1 for racing.

Product Features:

Thicker Than Stock Steel Plate
Ring Gear Securely Welded
Dual Bolt Patterns
Zinc-Dichromate Plated To Resist Corrosion
Withstands High Torque and RPM

from

$168.89

Hypertech ThermoMaster Power Chips are engineered for stock 1995-1981 GM vehicles (premium octane fuel required). The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. ThermoMaster Power Chips are designed for daily street driving or competition in unmodified vehicles using a 160 Deg. or 180 Deg. thermostat. Hypertech Power Chips(TM) are emissions certified 50-state legal (application specific).

Product Features:

Use w/Low-Temp 160-180 Deg. PowerStat Thermostat
Controls Engines Air/Fuel Ratio
Controls Spark Advance For Max Power
Potential Gas Mileage Improvements
No Wiring Or Soldering Required
Installs In Less Than 30 Minutes
Product might not be available in all states due to local laws.

from

$65.99

The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.

Product Features:

Helically wound conductor suppresses electro and radio noise
Kevlar core combination for great strength and durability
Heavy Duty Terminals For Secure Connection
8mm silicone and synthetic jacket resists heat and abrasion
500 Ohms/ft. Resistance For Improved Spark Delivery And Power
Silicone Boots Protect Against High Exhaust Temps

from

$307.99

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:

Maximum Cooling for Street and Racing Engines
Internal Passages Are Balanced for Maximum Flow
Impeller is Larger than Others For Max Pressure
Impeller Vanes Dramatically Increase Flow Rates
Equal Distribution to Both Sides of Block
Only Flows in One-Direction for Optimum Efficiency

from

$1009.99

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
64cc Combustion Chambers Improve Performance
Retain Stock Compression Ratio

from

$566.99

Edelbrock part #21011 Performer intake manifold is designed for street 1955-86 small-block Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent throttle respons

from

$17.99

Product Features:

For Small-Block Chevy
One Piece Configuration
Includes Front Cover Gasket & Front Seal
Includes Necessary Gaskets & Crankshaft Oil Seal
For Replacement Or Installation

from

$211.99

Product Features:

GM10.5″ 14 BOLT OPEN EMPTY CASE 4:10 & DWN

from

$203.99

Edelbrock part #9646 Pushrods are designed for small-block Chevy V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise forme

Product Features: