GMC C3500 Air Intakes
Top GMC C3500 Air Intakes Categories
We carry over 243 Air Intakes in inventory for the GMC C3500. If you’re looking for aftermarket Air Intakes for your GMC C3500, check out all these categories:
Essential GMC C3500 Air Intakes
Holley – Prem Street Carbs (Avengers) (Part No.0-81570)
from
$671.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Manual Choke For Precise Cold Start Control
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Mr. Gasket – Intake Bolt Kit (Part No.5003)
from
$87.99
Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.
Product Features:
See More
Product Features:
- Chrome plated
- Grade 8
- 12-point head
- AN washers with no exposed shoulder for a professional appearance
Felpro – Carburetor Choke Tube Gasket (Part No.72591)
from
$4.49
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Carburetor Gasket Kit #12371 Fits 4160 Carburetors (Part No.12371)
from
$20.99
The Edelbrock #12371 kit includes the primary fuel bowl gasket, the primary metering block gasket, the secondary metering block gasket and a metering plate gasket. The Edelbrock #12371 fits Holley 4160 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block Type
- Set of 4
- Fits Holley® 4160 Carburetors
- Made In The USA
Edelbrock – Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs (Part No.12412)
from
$26.99
The Edelbrock #12412 Vacuum Secondary Spring Kit includes 7 springs that will fit on Holley 4150, 4150HP, 4160 series and various Demon Carburetors.
Product Features:
See More
Product Features:
- Steel Material
- For Holley® 4150, 4150HP, 4160; Demon King, Mighty, Race, Road, Sea, Speed; Barry Grant Claw
- Includes Lightest To Heavy
- Set of 7
- Made in The USA
Dorman – Nylon Nut – 1/4 In. (No.14) (Part No.961-351D)
from
$4.99
Constructed of quality materials, this multi-purpose retainer provides the same function and versatility as the original equipment retainer ensuring long service life.
Product Features:
See More
Product Features:
- Ideal replacement – this retainer matches the fit and function of the original equipment retainer for this vehicle application
- Quality material – this retainer is made of durable material for long-lasting service
- Versatile design – this retainer is suitable for a variety of automotive uses
- Excellent value – this part offers original equipment quality at a competitive cost
Felpro – Fuel Injection Throttle Body Mounting Gasket (Part No.60903)
from
$10.49
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Each gasket is built to meet or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered and manufactured specifically for the repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Carquest – Carburetor Choke Thermostat (Part No.779-1485)
from
$69.05
Carquest distributes a full line of engine management products, providing the aftermarket with premium quality and comprehensive coverage.
See More
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1746)
from
$21.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Felpro – Air Cleaner Mounting Gasket (Part No.60038)
from
$4.29
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Mr. Gasket – Ultra-Seal Intake Manifold Gasket with Silicone Beading (Part No.5821)
from
$34.99
Mr. Gasket Ultra-Seal Intake Manifold Gasketss are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For original equipment replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.
Product Features:
See More
Product Features:
- Manufactured from cellulose/nitrile composition gasket material
- Provides excellent sealing and durability
- Silicone beading on both sides of each gasket
- Complete with manifold end seals and distributor gasket
- For OE replacement, high performance street, drag race and oval track use
Dorman – Help – Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (Part No.10232)
from
$5.99
Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.
Product Features:
See More
Product Features:
- Manufactured from high quality materials for a long service life
- Torque values listed on parts (where applicable)
- Easy to install
- Constructed to strict engineering quality standards
Edelbrock – Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors (Part No.12403)
from
$43.99
The Edelbrock #12403 Accelerator Pump Cam Kit Assortment Package of 8. These accelerator pump cams will have different shapes and profiles, allowing you to fine tune the accelerator pump’s performance to the engine’s requirements. Cam “lift” will directly
Product Features:
See More
Product Features:
- Multi-Color
- Plastic Material
- Fits Holley® 2300, 4150, And 4160 Carburetors
- Set of 8
- Made In The USA
Wells Vehicle Electronics – Carburetor Choke Pull-Off (Part No.1C1044)
from
$39.99
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
NTK – Throttle Position Sensor (Part No.TH0033)
from
$65.99
The Throttle Position Sensor (TPS) reports the angle of the throttle plate and thus the engine air intake to the ECM for optimal engine operation under all engine load conditions. Located on the throttle body, a failed Throttle Position Sensor may result in poor engine performance including stalling, hesitation, rough idle, increased fuel consumption, unnecessary stress on the emissions system and check engine light illumination.
Product Features:
See More
Product Features:
- OE MATCH: Throttle Position Sensors are manufactured to operational performance standards to meet or exceed OE fit, form and function to ensure proper feedback to the ECU to control engine performance.
- THE DIFFERENCE: Magnet size and strength optimized for precise output signal. 100% thermo-shock and vibration tested to ensure the best performance in extreme conditions.
Dorman – Upper Plastic Intake Manifold – Includes Gaskets (Part No.615-181)
from
$99.99
This engine intake manifold was precision-engineered and durably manufactured to match the fit and function of the original manifold on specified vehicles. It is thoroughly tested to ensure top-quality OEM construction and superior reliability.
Product Features:
See More
Product Features:
- Ideal replacement – this intake manifold was precision-engineered and durably manufactured to match the fit and function of the stock manifold on specified vehicles
- Reliable construction – tested to ensure top-quality OEM performance and durability
- Perfect fit – designed to match all specifications of the original part for convenient, trouble-free installation
- Trustworthy design – built by the industry leader in aftermarket manifolds
Edelbrock – Standard Main Jet Carburetor Metering Jet #12456 Size .055 (Pair) (Part No.12456)
from
$14.99
The Edelbrock 94 #12456 Carburetor Jets .056″ Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 56 Maximum Jet Size
- 0.055 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Carburetor Gasket Kit #12380 Fits 4150 And 4160 Carburetors (Part No.12380)
from
$18.99
Product Features:
See More
- The Edelbrock #12380 Metering Block gasket is made of black nitrile material and will ensure a leak-free seal from your Carb to the metering block.
- The Edelbrock #12380 Metering Block gasket will fit 4150 &4160 Carburetors.
- These will not work with accelerator pump transfer tubes.
ACDelco – Fuel Injection Throttle Body Gasket Kit (Part No.219-607)
from
$77.99
ACDelco Professional Fuel Injection Throttle Body Repair Kit contains high quality aftermarket replacement components for one or more of the following vehicle systems: ignition, and/or engine fuel management. This premium aftermarket kit contains components that are manufactured to meet or exceed your expectations for fit, form, and function.
Product Features:
See More
Product Features:
- Professional, premium aftermarket replacement
- Provides the performance and dependability you expect from ACDelco
- Manufactured to meet expectations for fit, form, and function
Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)
from
$22.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23
Product Features:
See More
Product Features:
- Center Hung Floats
- 0.11 in. Needle Diameter
- Viton® Needle Material
- Sold Individually
- Non-Adjustable Type
Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)
from
$66.99
Product Features:
See More
- Customize Carburetor Calibration and Performance
- Owners Manual has Assembly Help
- Includes Metering Rod Retaining Spring
- Includes Metering Rods
- Includes Metering Jets
- Includes Step-Up Springs
Edelbrock – Chevrolet SB Performer EPS Manifold w/ Gaskets, Bolts, Studs (Part No.2040)
from
$299.99
Edelbrock part #2040 Manifold Installation kit will simplify the process of adding more power and efficiency to your street rod or muscle car. It combines all the necessary components to replace your stock iron intake manifold with an Edelbrock aluminum i
See More
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$13.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Edelbrock – Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1221)
from
$46.99
Stamped from 18 gauge steel. Triple-chrome plated. High quality finish. Great looks. Works with all 5.152 inch carburetors. Base knock-outs for use with crankcase ventilation.
Product Features:
See More
Product Features:
- Stamped From 18-Gauge Steel
- Triple-Chrome Plated
- High-Quality Finish
- Great Looks
- Works With All 5.125 in. Carbs
- Base Knock-Outs For Use w/Crankcase Ventilation
Edelbrock – Pro-Flo Black 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1223)
from
$50.99
Product Features:
See More
- Edelbrock triple chrome-plated round air cleaner #1223 work with all popular 5-1/8″ diameter Carburetors (Performer Series, Thunder Series AVS, Holley, Thermo-Quad, Quadra jet and Carter AFB).
- The 10″ and 14″ models have knock-outs in the air cleaner base for use with Edelbrock crank case ventilation adapter #1205 (sold separately).
- #1208, #1209 and #1221 fit all Edelbrock Carburetors.
- Heights of air cleaners are in parentheses, measured from the gasket flange to the top of the supplied retaining nut.
- Dimensions are accurate within 1/8″.
GMC C3500 Air Intakes Categories
Helping You Find the Right Air Intakes for Your GMC C3500
You love your C3500. So we’ve made it easier than ever to help you find GMC C3500 Air Intakes in our online catalog. Our inventory holds 243 aftermarket and OEM Air Intakes for your GMC C3500, ranging from $4.29 to $1,972.99.
We offer parts from 17 brands trusted to make quality Air Intakes for your GMC C3500. Before you buy, take some time to read through customer reviews. We currently have 7,105 reviews of GMC C3500 Air Intakes from previous customers. Some of the top rated parts include Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet with 4.7 stars and Engine Intake Manifold Bolt Set with 4.8 stars.
Find your C3500 Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your GMC C3500 part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Air Intakes Brands for Your GMC C3500
Our inventory holds Air Intakes for your GMC C3500 from 17 trusted brands. You’ll find OEM and aftermarket parts from brands like FELPRO, Edelbrock, and Carquest Premium, all of which can keep that GMC happy.
We have Delphi parts available for your GMC C3500 in categories like Throttle Bodies & Carb Parts. Some of the top-rated Delphi parts in these categories are:
Top-Rated Felpro Air Intakes
Leading Felpro Air Intakes
We carry Felpro brand parts for your GMC C3500 across several catalog categories, including Intake Manifold Parts. Some of our most reviewed Felpro parts include:
FAQs for GMC C3500 Air Intakes
What are the most purchased Air Intakes for the GMC C3500?
Out of 243 Air Intakes for the GMC C3500, the most popular in our inventory are:
from
$446.99
(10)
AVS2 1906 Carburetor: 650 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
What are the top-rated GMC C3500 Air Intakes?
Top-rated Air Intakes for your GMC C3500 based on customer reviews/ratings are:
from
$428.99
(55)
Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
“Easy bolt on installation”
from
$42.99
(22)
Engine Intake Manifold Bolt Set
“These are 5/16″ bolts, but have the ball-end to supposedly prevent over-tightening. They also have a washer-type surface and thread-locker applied. Th”
