Ford LTD II Performance and Racing Products

Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).

Product Features:

• Glass Filled Polyester Case
• Longer Spark Duration
• Increased Performance
• No Energy Loss Due To Arcing
• Includes Brass Contact Terminal

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

• Repairs That Leaky Rear Main Sail
• Silicone Rubber to Withstand Extreme Engine Oil Temperatures
• Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
• Injection Molded for Precise Fit

Brake Bleeder Screws

Use the B&M Transpak to recalibrate your automatic transmission for optimum performance. With the Transpak you will be able to downshift into low at any speed, and keep it in low to any speed that you want.

Product Features:

• Recalibrate Auto. Transmission
• Optimum Performance
• Select Your App. Mode
• Improves Transmission Life
• Trans. Removal Not Required

Product Features:

• Designed for Optimum Torque and Acceleration
• Maximum Performance From Idle through Mid-Range
• Matched to Edelbrock Performer Intakes
• Includes Hydraulic Lifters and Assembly Lube
• Major Improvement in Throttle Response and Torque
• Use For Daily Drivers/Trucks/Vans/RVs/4x4s
• Take The Guesswork Out Of Camshaft Selection

MSD Pro-Billet Distributors are the finest performance and racing distributors available. Every feature has been engineered to endure the rigors of high performance and racing engines. Whether cruising the streets or racing stock cars, dragsters, boats or trucks, MSD has a distributor for it. MSD uses state-of-the-art, Computer Numerical Controlled (CNC) mills and lathes to machine each housing. After a long series of precise cuts and movements, the billet is formed into a flawless distributor housing that is accurate to within 0.001″. The flex-free housings are lightweight, have no porosity or weak areas and look great on polished, show quality engines.

Product Features:

• Same features as PN[8584]
• Use w/Edelbrock Victor Jr. man. for add. clearance at water neck
• No CARB Exemption Order Number
• Maintenance-free magnetic pickup and precision reluctor create stable trigger signals throughout the RPM range
• Polished steel shaft is QPQ coated and guided by two sealed ball bearings
• Advance weight pins are staked and tig welded to the plate
• Supplied with cap-a-dapt and rotor (accepts MSD socket style caps)
• Must be used with an MSD Ignition control

Product Features:

• Service Part
• Makes Connections Quick And Easy

Mallory distributor gears are precision machined from alloy steel in our factory to exact original equipment specs. For use with cast flat tappet hydraulic/mechanical cams and austempered ductile iron roller cams.

Product Features:

• Replacement Distributor Gear

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:

• Indicates coolant temperature
• Helps prevent coolant injuries
• Fahrenheit and centigrade readings
• Color-coded temperature ranges
• Integrated coolant reclamation valve
• Improves under-hood appearance
• Chromed crown with a colored trim ring

The B&M Megashifter has it all, form, function and classic style. This all adds up to bring you a quality shifter that’s been one of the most popular automatic shifters of all time. The light truck Megashifter is better suited for truck and bench seat applications with its overall height of 14.85-inches tall (2.25-inches taller than #80690 Megashifter.) The positive ratcheting action won’t allow you to over-shift and miss a gear at that critical moment, along with the reverse lockout feature meets NHRA/IHRA safety rules for those weekend grudge races at the track, while the look and feel of the T-handle and accordion style shift boot really shows off its racing heritage. Other features include a black console that you can trim to match the contour of your vehicle’s floor, 5-foot long shifter cable, cable brackets, transmission shift levers, chrome plated top plate with lighted gear indicator and everything needed for an easy at home installation. An optional T-handle with a 12-volt button is available separately for actuating a trans-brake, nitrous oxide or other accessories for the hard-core performance enthusiast. This shifter fits most popular Chrysler, Ford and GM 3 and 4-speed automatic transmissions. Note: AOD transmissions require optional kit #40496, GM 4L60E through 4L85E transmissions with PRNDL switch will require optional kit #70499. Overall Dimensions – 14.9L x 6.4W x 14.8H

Product Features:

• Universal Floor Mount Application
• Cable Operated
• Quick Installation
• Accurate Shifting
• NHRA/IHRA Reverse Lockout Meets Requirements
• Use w/Reverse Pattern Valve Body
• Includes Neutral Safety Switch
• Includes Backup Light Switch

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
• Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
• Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
• Slotted bolt holes allow for easier header installation.
• Not intended for use in emission controlled vehicles.

Product Features:

• FORD 9″ EMPTY POSI CASE – 28 & 31 SPLINES

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Ultra-Seal is Mr. Gasket premium valve cover gasket material. It’s manufactured from a high density cork and rubber blend with a black latex coat applied to the outside to help seal minor flange irregularites and eliminate oil leakage. It creates a positive seal by controlled swelling of the gasket material when exposed to hot oil. For original equipment replacement, high performance street, drag race and oval track use. Sold as a pair. These gaskets are .187 inch thick.

Product Features:

• Manufactured from high-density cork /rubber blend gasket material
• A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage
• Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil
• For OE replacement, high performance street, drag race and oval track
• .187″ thick
• Handles Ex Flange Pressure
• Forms Leak Proof Seal
• Black Latex Coating

These COMP Cams Ultra-Gold Aluminum Roller Rocker Arms with a 3/8″ stud diameter and 1.6 ratio are designed for Ford V8 289-302-351W applications. The new modern design features of these Ultra-Gold Rockers are proven to withstand extremely aggressive spring pressure and valve lift. Designed specifically for high performance street and race engines, the Ultra-Gold Aluminum Rocker Arms are precision CNC-machined to strict tolerances. Developed to meet the demands of professional engine builders, these rockers include features never before possible in an aluminum rocker arm.

Product Features:

• CNC-machined, lightweight design removes weight and yields unrivaled quality and ratio accuracy
• Designed for high performance street and race engines
• Precision-sorted trunion bearings withstand elevated valve spring pressure and valve lift
• Additional clearance, up to 1.650″ O.D. valve spring

These performance polyurethane components help reduce common wheel roll-under. This occurs when stopping abruptly, especially when using performance tires for both front of rear drive vehicles is so equipped. Replaces that original, short lived and too-soft O.E.M, rubber on front wheel drive vehicles – diminishes wheel hop and traction loss during standing start accelerations. Better maintains proper alignment under extreme conditions. Made of Energy’s Hyper-Flex performance polyurethane to add both performance and durability.

Product Features:

• Made from HYPER-Flex Polyurethane

All the quality and performance you’ve come to expect from MSD is now available in black. Our customers have requested black parts for their builds so we’ve answered with the addition of several black distributor caps and cap and rotor kits. The black parts are built to the exact specifications of the traditional MSD red components. If you’re looking to change up the look under the hood of your street machine, off-road rig or race car; check out the complete line of MSD black components.

Product Features:

• Injection Molded From DuPont Rynite Material
• Extreme strength; high dielectric properties
• Designed with performance in mind
• High quality; voltage insulating material
• Brass terminals
• Black in color

Made of high durometer, very firm, Hyper-Flex performance polyurethane. They’re economical, increase efficiency and are easy to install. Use Energy Suspension sway bar end links with sway bar bushings to get the maximum performance benefit. Combine both for the same effect as buying a larger sway bar. Together they offer a dramatic improvement in performance and handling.

Product Features:

• Made from HYPER-Flex Polyurethane
• Allows Vehicle to Work At Maximum Efficiency
• Easy to Install
• Superior Performance and Greater Longevity
• Lasts Much Longer Than OEM Rubber End Links

Edelbrock #88433 Water Pump Ford 1970-78 302 & 1970-87 351w v8 black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cool

Product Features:

• Standard Impeller Rotation
• 0.625 in. Pilot Shaft
• 0.750 in. Ball/Ball Bearing
• 5.70 in. Block To Hub Height
• Black Finish

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

• Easy to Install
• Superior Material
• Saves Your Tie Rods
• Lasts Longer
• Looks Great

If you want to update just your camshaft and aren’t doing a complete engine overhaul, this kit contains all the gaskets needed to change out your camshaft. That way you don’t have to buy a complete gasket kit just to change the cam, but still can replace all the gaskets you should in the process.

Product Features:

• Contains all the gaskets needed to change out your camshaft
• Fuel Injector O-Ring Not Included
• Meets Performance Standards

Product Features:

• FRD 10BLT 9.0 R/P 4.30 MGP

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:

• High Output Fuel Flow
• Flows 110 gph Free Flow
• Shutoff Pressure Pre-Set From 6.5 To 8 PSI
• Fuel Pressure Regulator Is Not Required
• Heavy Duty Construction For Continuous High rpm Operation
• Fuel Body Casting Can Be Rotated For Plumbing Situations
• Inlet And Outlet Tapped For 3/8 in. NPT
• Inlet/Outlet Tapped For 3/8 in. NPT