from

$289.99

Yukon yoke for Chrysler 9.25″ with a 7260 U/joint size. 2.125″ snap ring span, 1.078″ cap diameter. Inside snap ring.All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler 9.25″ rear
29 spline
7260 u-joint size
Inside snap ring design
2.125″ snap ring span
1.078″ cap diameter
Strap style

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$152.99

Set-up bearing (one bearing). HM803149. No return.

Product Features:

Set up bearing
Fits HM803149 pinion bearing
Easily slips on and off pinion journal to allow for pinion depth adjustment

from

$209.99

USA Standard Gear open spider gear set for Chrysler 8.25″, 27 spline .

Product Features:

Spider gear kit
Fits Chrysler 8.25″ 27 spline open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$252.99

Yukon 1541H alloy rear axle for Chrysler 8.75″ measuring 30″ with 30 splines and 5×4.5 bolt pattern. for use with C & E-Body only. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. Must use Green bearing.

Product Features:

Fits Chrysler 8.75″
30 spline
30″ long
5 x 4.5″ bolt pattern

from

$159.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 1976 and up Chrysler 8.25″
Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$117.99

Product Features:

PINION YOKE
CAST:1310
U-BOLT STYLE

from

$26.99

8.25″ Chrysler pinion gear thrust washer.

Product Features:

Pinion gear thrust washer
Fits Chrysler 8.25″

from

$232.99

Product Features:

Clutch kit
Fits Dana Spicer 44 and Chrysler 8.75″ Powr Lok
Aggressive design

from

$8.99

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
For Trac Loc positraction applications only

from

$215.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits HM89410 race
All steel construction

from

$6.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$919.99

Yukon yoke for Ford 8.8″ truck or passenger with a 1330 U/joint size. 3.625″ snap ring span, 1.125″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 8.8″
30 spline
1330 u-joint size
3.625″ snap ring span
1.062″ cap diameter
Outside snap ring design
Strap style

from

$9.49

Product Features:

Brand may vary by location

from

$829.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

Fits Chrysler 9.25″ rear
4-spring, clutch style positraction
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$51.99

Product Features:

MINI INSTALL KIT CHRYSLER 8.75 8 3/4″ LATE

from

$12.99

8.25″ Chrysler cover gasket.

Product Features:

Cover gasket
Fits Chrysler 8.25″

from

$8.99

Ring gear bolt for Chrysler 7.25″, 8″ IFS, 8.25″, 8.75″ & GM 7.2″ IFS front. 3/8″ x 24.

Product Features:

Ring gear bolt for Chrysler 7.25″, 8.0″ IFS and 8.75″
3/8″ x 24 thread
.866″ long

from

$64.99

Differential side bearing screw adjuster for 9.25″ Chrysler.

Product Features:

Side adjuster for Chrysler 9.25″ rear

from

$231.99

A worn or damaged differential pinion flange can lead to driveline vibrations and fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.

Product Features:

Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles
Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$78.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for ’76 & up Chrysler 8.25″ rear.

Product Features:

Fits 1976 and up Chrysler 8.25″
Includes carrier bearings and races

from

$9.99

Product Features:

Cross pin bolt for Dana Spicer 60 with c-clip axles

from

$469.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty. This is a fine spline pinion which takes a 29 spline yoke.

Product Features: