Chevrolet SSR Performance and Racing Products

The REACT offers fully customizable control over your vehicle’s throttle response. The simple control knob allows you to switch between multiple modes and control the throttle intensity of each mode on-the-fly. The REACT installs easily and is completely plug-and-play, has an automatic setup sequence so no disassembly is required, comes with a magnetic A/C vent mount (Pedestal swivel mount also available – Sold separately at hypertech.com/REACT.aspx), and doesn’t void your factory warranty. Plus the REACT is internet updateable. Three (3) versions of the REACT throttle optimizer are available to fit your particular driving needs… Performance, Off-Road, and Tow.

Product Features:

• On-The-Fly Adjustments
• LED Setting Indicators
• Multiple Levels Of Safety Protection
• Magnetic A/C Vent Mount Incl. [No Screw Or Tape]
• Pedestal Swivel Mount Available [Sold Separately]
• Custom Tuning Software
• Internet Updateable
• Easy Plug-N-Play Install
• Automatic Setup Sequence [No Disassembly Required]
• Doesnt Void Factory Warranty
• Product might not be available in all states due to local laws.

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Bolt-on Performance
• Custom Fit For Make And Model Listed
• Wires Are Pre-Cut To Exact Specifications

Designed to open at 160 degrees every time, regardless of engine rpm, and it’s high-flow design and brass and copper construction eliminate the damaging effects of cycling when you’re stuck in stop-and-go traffic. It includes the rubber gasket and has a pressure relief valve.

Product Features:

• Opens sooner than stock at 160 degrees
• High flow design for performance applications
• Includes rubber o-ring seal/gasket
• Incorporates pressure relief valve

Hays aluminum flywheels are manufactured from certified billet material that will not break up under the stress of high RPM and severe punishment of racing. Features replaceable steel surface insert. Precision balanced to either neutral (internal) or Detroit (external) specifications. Meets SFI specification 1.1 for racing.

Product Features:

• Certified Billet Material
• Borg and Beck Clutch Pattern
• Long-Style Clutch Pattern
• Ring Gear Securely Mounted To Prevent Spinning

The K&N 57-3046 FIPK air intake system replaces the restrictive factory air filter and air intake housing in some Chevrolet SSR V8 models. K&N intakes are designed to dramatically reduce intake restriction as they smooth and straighten air flow. This allows your engine to inhale a larger amount of air than the factory air filter assembly. More air means more usable power and acceleration throughout the engine’s RPM range. The 57-3046 air intake comes with an ultra-light carbon fiber topped and flanged K&N high-flow air filter and a heat shield that installs into the previous air box space. Air is directed through an aerodynamically engineered intake tube into the engine’s throttle body for a guaranteed power gain. The oversized oval shaped air filter can be used for up to 100,000 miles before servicing is needed depending on driving conditions. This air intake is relatively easy to install usually in 90 minutes or less using existing factory mounting points and accommodates the factory mass air sensor. The tools needed are a screwdriver, a ratchet set and an Allen wrench.

Product Features:

• GUARANTEED INCREASE IN HORSEPOWER: Dyno-tested with up to 50% more airflow than restrictive factory box air filter and intake tube
• BETTER TOWING: Improves acceleration and uphill performance when towing by improving throttle response.
• IMPROVED ENGINE SOUND: Hear the power under the hood.
• WORLD CLASS PROTECTION: Pushing the limits of engine protection by protecting your engine from harmful contaminants
• EASY MAINTENANCE: No filter cleaning required for up to 100,000 miles
• EASY TO INSTALL: Bolt-on power in less than an hour with basic hand tools. K&N air intake systems are one of the easiest ways to guarantee an increase in horsepower.
• DYNO TESTED: Dyno-tested for a guaranteed increase in horsepower and acceleration with no ECU tune required
• HIGH QUALITY: Made in America.

Edelbrock part #7343 RPM-Link adjustable true-roller timing chain Set now, you can dial-in your camshaft with ease with our RPM-Link Roller Timing Chain Set. RPM-Link timing chain bolt onto your engine just like any other timing chain set, so there’s no m

Product Features:

• Keyway Adjustable
• Single Roller Timing Chain Type
• Induction Hardened Billet Steel Material
• No Machining Required
• No Special Offset Bushings Needed For Installation

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

Product Features:

• HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
• VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
• PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
• EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
• EASY TO REMOVE: Fast and easy Wrench-Off removal
• HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
• HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers

COMP Cams GM LS Series RPM Valve Train Upgrade Kits replace stock valve train components for more usable horsepower and a higher rpm operating range. This kit includes Hi-Tech Pushrods, Beehive Valve Springs and Titanium Retainers.

Product Features:

• For GM LS series applications
• includes Hi-Tech Pushrods, Beehive Valve Springs and Titanium Retainers
• Replaces stock valve train components for more usable horsepower and higher rpm range

With a .625″ maximum lift, these Beehive Valve Springs were designed for hydraulic roller cams in LS1, LS2 and LS6 engines. COMP Cams Beehive Valve Springs deliver increased valve train stability and a much lighter valve train. This is achieved with less spring pressure for better valve control and reduced weight of both the spring and retainer. The unique Beehive shape handles valve train stress more efficiently to eliminate damaging harmonics and increases high RPM horsepower and durability. The oval/multi-arc wire shape places the maximum area of the wire at the point of highest stress to handle valve train stress more efficiently and allow better heat dissipation for longer life. Because of the unique Beehive design, the valve train can handle more RPM and more aggressive cam profiles.

Product Features:

• Seat pressure: 125 lbs. @ 1.800″, Open Pressure: 367 lbs. @ 1.150″
• O.D.: 1.075″ (Top) 1.310″ (Bottom), I.D.: .650″ (Top) .885″ (Bottom)
• Designed for hydraulic roller cams
• .625″ maximum lift, 1.310″ O.D.
• Originally designed for LS engine applications but will work in 5.7L Hemi engines and many others

HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) Application: HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• New Turbine Hub
• New Springs/Rollers In Stator

This 7° steel retainer for GM Gen III applications with #26915 or #26918 Beehive Valve Springs is precision machined from 4140 chromemoly steel and finished in black oxide. This precision retainer is specifically designed for positive location when combined with COMP Cams high-quality valve springs.

Product Features:

• 7° angle retainers for 1.055″ diameter valve springs, stock diameter valve stems
• O.D. – 1.030″, Step 1 – .640″
• Precision machined from 4140 chromemoly steel and finished in black oxide
• Designed for positive location when combined with COMP Cams high-quality valve springs

Assure a steady, precise metered flow of nitrous and fuel for reliability. Backed with years of laboratory research, as well as dyno and drag strip testing. NOS Injector Plates are available for those who want to build their own system or upgrade their current nitrous system without having to go through the expense of a new complete system. Unless specified, NOS Injector plates incorporate a low profile 1/2 inch thick design and are constructed of solid billet or die cast aluminum with a durable black finish. Included are all applicable gaskets, studs, jets and plumbing.

Product Features:

• Convert Existing Nitrous Kit To New Technology

Designed to take advantage of the GM LS engine’s larger camshaft journal diameter, the XFI RPM camshaft line takes Xtreme Energy technology to deliver excellent power.

Product Features:

• Designed with Xtreme Energy technology to provide excellent power with the LS engine’s enhanced cylinder head design and high RPM potential.
• Takes advantage of the LS engine’s larger journal diameter, base circle and 1.7+ rocker arm ratio.
• Provides outstanding low RPM torque with increased stability.

The B&M Megashifter has it all, form, function and classic style. This all adds up to bring you a quality shifter that’s been one of the most popular automatic shifters of all time. The light truck Megashifter is better suited for truck and bench seat applications with its overall height of 14.85-inches tall (2.25-inches taller than #80690 Megashifter.) The positive ratcheting action won’t allow you to over-shift and miss a gear at that critical moment, along with the reverse lockout feature meets NHRA/IHRA safety rules for those weekend grudge races at the track, while the look and feel of the T-handle and accordion style shift boot really shows off its racing heritage. Other features include a black console that you can trim to match the contour of your vehicle’s floor, 5-foot long shifter cable, cable brackets, transmission shift levers, chrome plated top plate with lighted gear indicator and everything needed for an easy at home installation. An optional T-handle with a 12-volt button is available separately for actuating a trans-brake, nitrous oxide or other accessories for the hard-core performance enthusiast. This shifter fits most popular Chrysler, Ford and GM 3 and 4-speed automatic transmissions. Note: AOD transmissions require optional kit #40496, GM 4L60E through 4L85E transmissions with PRNDL switch will require optional kit #70499. Overall Dimensions – 14.9L x 6.4W x 14.8H

Product Features:

• Universal Floor Mount Application
• Cable Operated
• Quick Installation
• Accurate Shifting
• NHRA/IHRA Reverse Lockout Meets Requirements
• Use w/Reverse Pattern Valve Body
• Includes Neutral Safety Switch
• Includes Backup Light Switch

Multi-Layered Steel (MLS) exhaust and header collector gaskets are designed for extreme cylinder pressures produced by high horsepower high compression turbo-charged, supercharged and nitrous oxide injected engines. Manufactured from three stainless steel layers, they resist corrosion, will not burn through or push out and maintain maximum fastener torque retention. Stress formed inner and outer layer embossments act like springs that rebound under exhaust flange clamp load, creating force to seal extreme exhaust pressures. Total gasket thickness .075 inch. Will not deteriorate from scrubbing action caused by different expansion rates in aluminum and steel materials.

Product Features:

• Multi Layer Stainless Steel 3-Layers
• Round Port 1.75″ Diameter
• Will not deteriorate from scrubbing action caused by different expansion rates in aluminum and steel materials.
• Thickness .072″
• Fits GM LS Series Engines 1997-’15

RngPnn

Product Features:

• GM 10BL 8.5 R/P 3.08 FRT/REAR MGP

Reduced Travel OE-Style Hydraulic Roller Lifter for ’87+ SBC, LT/LS and V6

LS Cast Iron Exhaust Manifold

LS Cast Iron Exhaust Manifold

The Super 40 features Flowmaster’s Delta Flow technology. It’s larger case profile provides the best of both worlds of performance and sound. The Super 40 has that deep powerful sound of the Original 40 series but with all the benefits of performance and low interior resonance from the Delta Flow technology. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

The Super 40 features Flowmaster’s Delta Flow technology. It’s larger case profile provides the best of both worlds of performance and sound. The Super 40 has that deep powerful sound of the Original 40 series but with all the benefits of performance and low interior resonance from the Delta Flow technology. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

Edelbrock #8895 Water Pump GM gen III ls1 & gen iv ls engines insert style ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “supe

Product Features:

• Standard Impeller Rotation
• 0.750 in. Pilot Shaft
• 0.750 in. Ball/Ball Bearing
• 6.00 in. Block To Hub Height
• Natural Finish

Edelbrock #8897 Water Pump gm gen III ls1 & gen iv ls, replacement insert ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super

Product Features:

• Standard Impeller Rotation
• Replacement Insert
• Service Part
• For Part Number 8896
• Satin Finish