Chevrolet R3500 Performance Engines

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:

• Maximum Cooling for Street and Racing Engines
• Internal Passages Are Balanced for Maximum Flow
• Impeller is Larger than Others For Max Pressure
• Impeller Vanes Dramatically Increase Flow Rates
• Equal Distribution to Both Sides of Block
• Only Flows in One-Direction for Optimum Efficiency

Holley designed these throttle bodies with all relevant emission provisions and hook-ups for a true 50 state legal installation. They are engineered for a bolt-on installation on stock factory Manifolds for the applications cataloged. The one barrel throttle bodies have been assigned California Air Resources Board (C.A.R.B.) Executive Order (E.O.) number D-115-4. The two barrel throttle replacement bodies are considered to be the functional equivalent of the original equipment throttle body and, as such, are considered to be 50-State legal.

Product Features:

• Direct Replacement For OE Units
• 2 in. Throttle Bore
• 42 percent Area Increase Over Stock TBI
• Including Air Distribution Ring
• Increased Torque and Horsepower
• 50 State Legal

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. Comes complete with cork front & rear manifold end seals. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

• Manufactured from cellulose/nitrile composition gasket material
• Provides excellent sealing and durability
• Die-cut for an excellent fit
• Can be trimmed if necessary for modified port applications
• Complete with cork manifold end seals & distributor gaskets if applicable
• For OE replacement, high performance street, drag race and oval track use

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
• NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
• SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
• STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
• DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 180 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts, the Xtreme Energy grind family offers gains in torque and horsepower while still delivering adequate vacuum for power brakes and other vacuum dependent accessories. Xtreme Energy camshafts work great in carbureted applications, but offer the best performance with aftermarket intake manifolds, lower gear ratios, headers and free flowing exhaust.

Product Features:

• HYDRAULIC – Xtreme Energy Computer Controlled: Great in throttle body, crossfire or carbureted engine and 305 TPI.
• 249/260 Advertised Duration, 206/212 Duration @ .050″, .434″/.444″ Lift, 112 Lobe Separation
• Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

• Features 12-point Smaller-than-standard Bolt Head
• Thick Flat Washers Distribute Optimum Clamp Load
• Ideal Use Where Space Is Minimal On Race Manifolds
• Bolts And Washers Zinc Plated For Protection
• Zinc Plated For Protection

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

• Good blend of efficiency and performance.
• Perfect choice for performance street rebuilds.
• Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

Product Features:

• Solid Bushing Chain Resists Stretching
• For Use with Stock or Edelbrock Camshafts
• Stressproof Steel Crank Gears
• 3 Keyway Setting Points To Ensure Accurate Timing
• True Bearing Surface Rolls with the Sprockets
• For OEM Hydraulic Roller Lifter Cams Only

Designed to keep the rocker arms positively locked for precise and critical valve train adjustments. Manufactured from quality grade steel, then heat-treated for extra strength and plated with a durable finish. Kits include 16 rocker arm nuts with socket head set screws and one hex key wrench.

Product Features:

• (16) Rocker Arm Nuts w/ Locks 3/8″-24 Threads
• Shank O.D. .540″
• Includes Locks and Hex Wrench
• High-Quality Grade Steel
• Heat-Treated For Ex Strength
• Plated With Durable Gold Tone Finish

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

• Application specific design to ensure a perfect fit
• Meets or exceeds all original equipment specifications
• Engineered and manufactured specifically for repair applications
• Unsurpassed quality you can trust
• Validated for fit, form, and function

Mr. Gasket Performance Timing Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

• Manufactured from high-density cork/rubber blend gasket material
• Provides excellent sealing and durability
• For OE replacement, high performance street, drag race and oval track use

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Rigid core, molded silicone rubber gaskets utilize the one-piece molded rubber technology for a perfect fit, ease of installation and include compression limiters to prevent overtightening.
• Not intended for use in emission controlled vehicles.

Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.brbrThese gaskets are .312 inch thick. That’s substantially thicker than stock which can allow for additional valve train clearance.brbrFits Chevrolet 396,402,427,454,502 Gen IV, Gen V and Gen VI Big Block.

Product Features:

• This Gasket Has A Cork Rubber Blend
• Provides Excellent Sealing And Durability
• Extra Thick For The Hard To Seal Applications

Manufactured from high quality machine finished aluminum, Spectre’s Throttle Body Spacers are engineered to improve engine performance. By providing added volume to the intake manifold and directing air through a tapered internal constriction, this spacer utilizes the Venturi effect to increase the speed of air flowing into your intake manifold. Spectre has designed a number of kits to fit a wide range of specific applications. Each kit includes the necessary gaskets and hardware to bolt directly to the factory components, making installation quick and easy.

Product Features:

• Includes the necessary gaskets and hardware to bolt directly to the factory components
• Each kit is designed for the applications listed
• Manufactured from high quality machine finished aluminum
• Can be installed in less than an hour using common hand tools with no drilling or cutting required
• Simple to install

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Product Features:

• Work with .530″ guides and 3/8″ valve stem diameter
• Valve stem oil seals keep unwanted oil from entering the combustion chamber
• Several different types of valve seals are offered

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.O.D. Dia. 1 I.D. Dia. 2 Damper Seat Load Open Load Coil Bind Rate (Lbs./In.) Titanium Retainer Steel Retainer Cup Seat Shims 1.524 1.110 Y 122 @ 1.900 309 @ 1.400 1.200 373 721, 732 1732, 741 4779* 4757

Product Features:

• Seat pressure: 122 lbs. @ 1.900″, Open Pressure: 309 lbs. @ 1.400″
• O.D.: 1.524″, I.D.: 1.110″
• Single valve springs with damper

Based on performer RPM-series with unique air gap. Air gap cooler and denser mixture for more power. Designed for 1500 to 6500 RPM street-driven power. Dual-plane high-rise intake with 180 degree firing order. Produces incredible top-end horsepower. Retains good throttle response and acceleration. Larger plenum and runners maximize other upgrades. Edelbrock total power package maximizes gains. Available in cast, polished or endurashine finish.

Product Features:

• Based on Performer RPM-Series with Unique Air Gap
• Air Gap Cooler and Denser Mixture for More Power
• Designed for 1500 to 6500 RPM Street-Driven Power
• Dual-Plane High-Rise Intake w/180 deg Firing Order
• Produces Incredible Top-End Horsepower
• Retains Good Throttle Response and Acceleration
• Larger Plenum and Runners Maximizes Other Upgrades
• Edelbrock Total Power Package Maximizes Gains

Product Features:

• Remote Thermostat Housing

Edelbrock part #9646 Pushrods are designed for small-block Chevy V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise forme

Product Features:

• 7.25 in. Length
• 0.312 in. Diameter
• 4130 Chromoly Steel Material
• Black Oxide Finish
• Made In The USA

Product Features:

• Use W/ Valve Springs Part #5703, 5794
• Set of 16
• 1.50 in. Outside Diameter
• Steel Material
• Black Oxide Finish

This is a high quality bolt set that is made of grade 8 steel and will meet your requirements for a quality bolt set, this set will work on original equipment, high performance street, drag or circle track applications.

Product Features:

• These Are Have A Zinc Dichromate Finish
• Tall Hex Head Bolt To Prevent Slippage
• Extra Thick Parallel Ground Washer
• Washers Provides More Accurate And Uniform Torque
• Grade 8 Alloy Steel

Secure the harmonic balancer or dampener on your Chevy. Works on original equipment, high performance street, drag or circle track applications. Features a heat treated black oxide coated Grade 8 alloy steel bolt for strength with a tall hex head to prevent wrench from slipping. An extra thick parallel ground washer provides accurate, uniform torque, and a lock washer is also included.

Product Features:

• Heat treated black oxide coated Grade 8 alloy steel
• Tall hex head bolt to prevent wrench from slipping
• Extra thick parallel ground washer provides accurate, uniform torque
• Washers Provides More Accurate And Uniform Torque
• Grade 8 Alloy Steel

The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, new turbine hub and dual pattern drive lugs on some GM Holeshots.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator