Chevrolet Celebrity Performance and Racing Products

ACCEL cap and rotor kits offer superior protection from “arc-thru” and crossfire. Features 60k V-rated alkyd compound, stress-relieved at molding to ensure stability. Brass inserts and steel rotor springs provide for high spark energy flow.

Product Features:

• See catalog for application information
• Features 60K V Rated Alkyd Compound

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

Product Features:

• HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
• VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
• PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
• EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
• EASY TO REMOVE: Fast and easy Wrench-Off removal
• HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
• HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers

Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:

• 3400-3800 RPM
• Small And Big Blocks
• Serious Performance
• Furnace Brazed
• Fully Balanced

Hypertech Power Chips are engineered for stock 1981-1995 GM vehicles. The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. Street Runner Power Chips are designed for daily street driving or competition in unmodified vehicles using a stock thermostat.

Product Features:

• Designed For Daily Street Driving
• For Unmodified Vehicles w/Stock Thermostat
• Controls Engines Air/Fuel Ratio
• Controls Spark Advance For Max Power
• Potential Gas Mileage Improvements
• No Wiring Or Soldering Required
• Installs In Less Than 30 Minutes
• Product might not be available in all states due to local laws.

Regain horsepower and economy for your street machine with a new ACCEL performance rotor. ACCEL’s high quality manufacturing process results in rotors offering superior protection from arc-thru and crossfire.

Product Features:

• Max Stability For All RPM Ranges
• Heavy Duty For Maximum Energy Transfer

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1955-85 GM small block (internally balanced) V8 engines along with 4.3L V6 engines. Also fits 1990 and earlier GM big block (internally balanced) V8 engines with two piece rear main seal. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.75 or 11.5 inch converter mounting locations, 168 tooth ring gear with double-sided welds for added strength and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953. Compatible with Powerglide, TH350, TH400 and TH700R4 automatic transmissions.

Product Features:

• NHRA/IHRA Legal For All Classes
• Includes SFI Certification Sticker
• Ideal For Street Applications
• To Extreme Duty Racing
• To High RPM Use

Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Compatible with late model GM computer controlled remote mount HEI systems. Direct bolt-in, plug-in replacement. Brass coil wire contact increases energy transfer and resists corrosion better than aluminum. Complete with new mounting hardware.

Product Features:

• 10-15% More Energy
• Direct Plug In Replacement Direct OE Fit
• Advanced Bobbin Technology
• Highly Specialized Silicone Magnetic Steel Cores
• Standard Motor Products SMP DR-37
• MSD 8226
• Resist Corrosion
• W/New Mounting Hardware

Hypertech Power Chips are engineered for stock 1981-1995 GM vehicles. The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. Street Runner Power Chips are designed for daily street driving or competition in unmodified vehicles using a stock thermostat.

Product Features:

• Designed For Daily Street Driving
• For Unmodified Vehicles w/Stock Thermostat
• Controls Engines Air/Fuel Ratio
• Controls Spark Advance For Max Power
• Potential Gas Mileage Improvements
• No Wiring Or Soldering Required
• Installs In Less Than 30 Minutes
• Product might not be available in all states due to local laws.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
• Not intended for use in emission controlled vehicles.

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

• Service Part
• No Moving Parts To Wear Out
• Self Contained Unit
• Can Drive OEM
• Can Drive High Performance Ignition Coils

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 180 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:

• Indicates coolant temperature
• Helps prevent coolant injuries
• Fahrenheit and centigrade readings
• Color-coded temperature ranges
• Integrated coolant reclamation valve
• Improves under-hood appearance
• Chromed crown with a colored trim ring

Product Features:

• Designed for Optimum Torque and Acceleration
• Maximum Performance From Idle through Mid-Range
• Matched to Edelbrock Performer Intakes
• Includes Hydraulic Lifters and Assembly Lube
• Major Improvement in Throttle Response and Torque
• Use For Daily Drivers/Trucks/Vans/RVs/4x4s
• Take The Guesswork Out Of Camshaft Selection

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
• Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
• Not intended for use in emission controlled vehicles.

Product Features:

• Matching Top For Edelbrock Base Intake PN[3785]
• Designed for OEM 2-barrel Carburetor
• Contains Necessary Linkage And Bracketry
• 50-State Street Legal if Correct Carburetor Used
• Accepts Stock EGR Connections
• Match With Edelbrock Valve Covers Pn[4488]

Product Features:

• For Idle to 5500 RPM Street-Driven Performance
• Excellent Throttle Response and Mid-Range Power
• 50-State Street Legal if Correct Carburetor Used
• Ideal for Light-Duty Pickups and Passenger Cars
• Unique Design Allows Use Of 2 bbl Or 4 bbl Top

The Edelbrock #4488 Signature Series Valve Covers are designed for Chevrolet 2.8L 60 Deg V6 ’82-93 applications. Engineered for function and styled for great looks, Signature Series valve covers have stock-style breather baffles that prevent oil passage to the PCV valve. These quality valve covers accept all emissions equipment, including PCV valve holes. Rubber grommets for the breather and PCV valve holes are included. Matching breathers sold separately.

Product Features:

• Chevrolet 2.8L, 60 Degree, 1982-93
• Short
• Chrome Steel
• Set Of Two
• Rubber Grommets For Breather

These ACCEL carbon and graphite core wire sets virtually eliminate RFI noise, while providing maximum conductivity for ultimate performance in any race or street application. Double silicon insulation eliminates leakage and misfire.

Product Features:

• Heavy Duty 8.8mm Oversized Silicone Jacket
• 500 Ohms/ft. Of Resistance
• 550 Degree Double Silicone Construction
• Fiberglass Braid
• Carbon/Graphite Core
• Magnetic Suppression
• Fiberglass/Kevlar Core
• 500 Ohms Resistance

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fel-Pro performance intake manifold gaskets have been tested with virtually all aftermarket cylinder head and intake manifold combinations.
• No exhaust crossover openings or blocking shields
• Embossed steel core laminate w/coating
• Not intended for use in emission controlled vehicles.

Fits Chevy small block 265-400 CID, Chevy big block 396-454 CID, & 90 degree Chevy V6. The Starter Motor Heat Shield is built with heat-resistant material sandwiched between two aluminum plates. The shield protects the starter from heat buildup from the exhaust system, especially important when using headers.

Product Features:

• Designed to prevent starter overheat due to extreme exhaust temperature
• Heat resistant material sandwiched between 2 aluminum plates
• Protects Starter From High Temperatures
• Made Of 2 Sheets Of Aluminum Heat Resistant Center
• Natural Finish