from

$97.99

A true performance application component for cars, trucks, hot rods, racing/competition, yet popularly used for street vehicles when more horsepower is added. Soft running enough to absorb vibrations for street use yet rugged for racing use. Helps control torque on high performance vehicles. Maintains proper drive shaft angle to help prevent early wear and unexpected power train damage. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal transmission mounts. Resistant to under vehicle fluid oils, coolants and road contaminants. Made of Energy’s Hyper-Flex performance polyurethane and heavy duty hardware – for added durability.

Product Features:

Unique Safety Interlock Design
Impervious to Vehicle Oils and Chemicals
Strong Enough Too Handle High Performance

from

$54.99

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:

Indicates coolant temperature
Helps prevent coolant injuries
Fahrenheit and centigrade readings
Color-coded temperature ranges
Integrated coolant reclamation valve
Improves under-hood appearance
Chromed crown with a colored trim ring

from

$10.99

Installs using stock timing cover bolts. Chrome plated steel is a much better compliment to a chromed timing cover. Has markings for 16 degrees before top dead center (BTDC) to 8 degrees after top dead center (ATDC).

Product Features:

Bolts on with existing timing cover bolts
Chrome plated steel is a much better compliment for chrome timing covers
Markings for 16 degrees BTDC to 8 degrees ATDC

from

$49.99

These are high quality gaskets that works well on those hard to seal applications. The low density fiber & rubber blend gasket material seals those minor head imperfections with a low clamp force. At .312 inch, the extra thickness can also offer slightly more clearance for roller rockers. Ideal for all those high performance applications where you take the valve covers off and on a lot, and sticking is a problem.brbrFits all 1965-2000 Chevy Big Blocks: 366,396,402,427,454 including GM (General Motors) Gen VI Crate Engines like the 502 and 572.

Product Features:

These Are A Cork Rubber Blend
Extra Thick 5/16 In Creates Positive Seal
Also Available In Standard Thickness
For OE Replacement And High Performance Apps

from

$50.39

Made of high quality stainless steel. These bolts will brighten up your hot rod, or improve the looks of your race car.

Product Features:

Bright Ball Burnish Finish
Made From 304 Stainless
Compact Hex Head Is Ideal Where Space Is Limited
16 per Package
Resist corrosion and provides a clean professional appearance

from

$46.99

Brake Bleeder Screws

from

$25.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$53.99

The cap and rotor of any ignition system must be considered maintenance items. Just as you change the oil and filter of your car, you should always replace the cap and rotor as a set. To make things easy, we now offer these cap and rotor replacement kits.

Product Features:

Fits MSD/GM V8 Distributors
Made from high quality materials
Brass terminals
High dielectric properties

from

$228.99

Performance Replacement HEI Distributor, direct plug-in with OE type connectors, GM HEI equipped Cars, Trucks (Pre-Computer). High dielectric strength cap, brass male towers. ACCEL Performance Replacement Distributors are the perfect choice for your daily driver or street machine. Using all new components, these distributors feature High-performance ACCEL Electronics. All new components-housings are either new castings or turned from billet stock, centerless ground shaft with oil lite bushings. High dielectric strength cap, balanced rotor. Male tower distributor cap with brass cap and rotor contacts (Ford and AMC Models feature screw-mounted wire retainer for the ultimate plug wire retention). Iron or steel distributor gear. Direct plug-in replacement with factory-type connectors for plug and play installation.

Product Features:

Direct Plug In Factory Replacement Plug And Play
CNC Machined 6061 T6 Billet Aluminum Housing
High Dielectric Strenght Thermoplastic Cap With Br
4 Topin Module With Dwell Control Triggers At 75 R
Easy Access Fully Adjustable Mechanical Advance
Adjustable Vacuum Advance
Includes Performance Coil
Fit non computerized vehicles

from

$33.99

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Product Features:

Work with .530″ guides and 3/8″ valve stem diameter
Valve stem oil seals keep unwanted oil from entering the combustion chamber
Several different types of valve seals are offered

from

$18.99

Chrome-plated for beauty and durability, wing bolts make valve cover removal fast & easy. They are precision-engineered and feature extra-long threads to accommodate Mr. Gasket re-usable valve cover gasket & custom valve covers.

Product Features:

Fits Chevy V8
Standard Y Top 1/4 In-20 X 5/8 in L
Chrome Plated Steel
Overall Length: 4.64″
Installed Length: 4.00″
Pack of 4

from

$73.99

These grade 8 alloy steel, longer length bolts are designed to compensate for thread length lost when using head bolt washers. This allows increased torque and clamping. Set of 16 does one cylinder head.

Product Features:

Cylinder Head Bolts
Longer-Than-Stock
High Quality Grade 8 Alloy
Increase Torque Settings
Higher Clamp Loads On Gasket

from

$389.99

The Edelbrock #4145 Classic Series Valve Covers are designed for Chevy 262-400 V8 1959-86 applications. Edelbrock first made these aluminum valve covers in the late ’50s and they’re still a classic. They are made of heavy-gauge sand-cast aluminum, Overall height is measured from base to top at the highest point. Edelbrock classic valve covers can be machined to accept breathers if desired.

Product Features:

Small Block Chevy 262-400 1959-86
Tall
Polished Aluminum
Set Of Two

from

$19.99

Rotor for Flame-Thrower cast distributors. Premium rotor with brass contact

Product Features:

PerTronix D660701 Rotor Flame-Thrower Billet Distributor
Rotor for Flame-Thrower cast distributors

from

$13.99

Precision cut to cover stock fuel pump opening when converting to an electric fuel pump. Gasket included.

Product Features:

Chrome Plated Steel
Comes With Gasket
Easy Installation

from

$838.99

For 3500 to 7500 PRM. Use where low-end torque is not a prime factor. Great for engines with slightly modified heads. HEI ignition will not clear manifold. Street machines, street rods, pro-street and marine.

Product Features:

For 3500 to 7500 RPM
Use Where Low-End Torque is Not a Prime Factor
Great For Engines w/Slightly Modified Heads
Top Has Vacuum Outlet for Power Brakes
Will Accept Forward and Sideways Mounted Carbs
Carburetor Center-to-Center Dimensions 9.38 in
HEI Ignition Will Not Clear Manifold
Street Machines; Street Rods; Pro-Street; Marine

from

$20.99

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

Zinc plated to resist corrosion and provide a clean professional appearance
Made from Grade 5 steel for strength and durability
Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
Allen (socket) Head
Zinc Plated For Protection

from

$46.99

Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Silicone beading on both sides of each gasket
Complete with manifold end seals and distributor gasket
For OE replacement, high performance street, drag race and oval track use

from

$499.99

Holley’s new 0-80457SA is constructed from aluminum which compared to its zinc counterpart equates to a weight savings of 40%! Holley’s aluminum 0-80457SA will hold its shine longer and also can be hand polished for a custom look! Its 600 CFM of airflow,

Product Features:

Vibratory Polished For Good Looks

from

$15.99

This is a high quality bolt set that is made of grade 8 steel and will meet your requirements for a quality bolt set, this set will work on original equipment, high performance street, drag or circle track applications.

Product Features:

Has A Zinc Dichromate Finish
Made Of High Quality Grade 8 Steel
Has A Tall Hex Head To Prevent Wrench Slipping Off
Extra Thick Parallel Ground Washer
Washer Provides More Accurate And Uniform Torque

from

$64.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets
50 State Street Legal

from

$199.99

Product Features:

Case-Hardened Tubing
Welded Ends
5/16 in. Diameter
Use with or without Hardened Steel Guideplates

from

$101.99

Product Features:

MINI SPOOL – DANA 44, 30 SPL.

from

$9.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Saves Your Tie Rods
Lasts Longer
Looks Great

from

$316.99

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features: