Chevrolet C10 Suburban Performance Engines

Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

• Complete with o-rings and mounting bolts
• Features an o-ring style seal to prevent water leaks
• Chrome plated
• 1/2″ NPT port can be used for various coolant temp related sensors or switches

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• Complete Kit: Includes Retainers And Locks
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Includes Superior Quality Steel Retainers
• Includes 7 deg. Heat-Treated Valve Stem Locks
• Retainers and Locks Black Oxide Coated
• Non-Rotator Style: Dyno Tested and Street Proven
• Great Match to Edelbrock Camshaft Kit

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 195 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

Includes: 2 short flat black valve covers 2 valve cover gaskets 1 flat black push-on breather 1 flat black dipstick & tube 1 flat black timing chain cover 1 flat black timing tab 1 rubber grommet for valve cover PCV hole 1 breather grommet

Product Features:

• Ideal Starter Kit
• Enhances Appearance

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
• Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
• Raises combustion sealing force to roughly three times that of standard head gaskets.
• Steel wire rings for the greatest combustion seal strength.
• Not intended for use in emission controlled vehicles.

HYDRAULIC – Mutha’ Thumpr: High performance street/strip, needs 9:1 compression, 2500+ stall, intake, gears and headers, rough idle.

Product Features:

• HYDRAULIC – Mutha’ Thumpr: High performance street/strip, needs 9:1 compression, 2500+ stall, intake, gears and headers, rough idle.
• 287/304 Advertised Duration, 235/249 Duration @ .050″, .510″/.495″ Lift, 107 Lobe Separation
• Valve spring upgrade required

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts.

Product Features:

• Best with aftermarket torque converters and 9.5:1 compression.
• Great high RPM power.
• Easy on valve train parts.
• Can be used with mild ratio rocker arms and traditional performance valve springs.

Product Features:

• Solid Bushing Chain Resists Stretching
• For Use with Stock or Edelbrock Camshafts
• Stressproof Steel Crank Gears
• 3 Keyway Setting Points To Ensure Accurate Timing
• True Bearing Surface Rolls with the Sprockets
• 50 State Street Legal

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longevity.
• Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
• Not intended for use in emission controlled vehicles.
• Not intended for use in emission controlled vehicles.

Product Features:

• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 deg. Firing Order
• Patented Runner Design Ensures Broad Torque Curve
• Excellent Throttle Response and Mid-Range Power
• 50-State Street Legal if Correct Carburetor Used
• Will Not Fit Under Corvette Hoods
• Available in Multiple Finishes
• Use Choke Rod PN[9179] for Stock Carburetor

These High Energy Die Cast Aluminum Roller Rocker Arms for Chevy V8 396-454 applications are perfect for street and moderate race use. With a 7/16″ stud diameter and 1.7 ratio, the die cast, larger-than-stock body of the rocker arms is made of aluminum for superior strength with light overall weight. High Energy Die Cast Aluminum Roller Rocker Arms from COMP Cams are an affordable option that feature a die cast, aluminum body with a needle bearing fulcrum and roller tip. Designed to be stiffer and more durable, these cost effective rocker arms are capable of providing added valve lift while withstanding the rigors of a performance application. Their specially engineered fulcrum and roller tip create far less friction than sliding factory models to lower oil temperatures, thus improving both response and horsepower. Snap rings are used to hold the trunion and bearings locked in place.

Product Features:

• Cost effective aluminum construction provides superior strength to weight ratio
• Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
• Durable design increases valve lift while withstanding the rigors of moderate race use
• Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

This Mr. Gasket Water Pump Bolt Set includes chrome plated grade 5 hex head fasteners and AN style washers to install the water pump on your small block Chevrolet with the short style water pump. AN washers have no exposed shoulder which offers a professional appearance. Includes one 3/8 inch-16 x 2-1/2 bolt, three 3/8 inch-16 x 1-3/4 inch bolts, and four 3/8 inch AN washers.

Product Features:

• Chrome plated
• Grade 5
• AN washers with no exposed shoulder for a professional appearance

Magnum Pushrods from COMP Cams offer an affordable solution for your .080″ wall chromemoly pushrod needs. Designed to withstand the stresses of a high performance engine, Magnum Pushrods are head-treated for extended durability and have precision formed, reinforced ends. Magnum Pushrods are black-oxide finished with their part number and length laser etched onto the surface for easy identification.

Product Features:

• 3/8″ Diameter, 7.800″ Length
• Magnum Pushrods for Small Block Chevy
• One-piece .080″ wall chromemoly steel tubing
• Heat-treated for extended durability and guide plate compatibility
• Precision formed and reinforced pushrod end

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Product Features:

• Work with .530″ guides and 3/8″ valve stem diameter
• Valve stem oil seals keep unwanted oil from entering the combustion chamber
• Several different types of valve seals are offered

Roller cam lobes are ground flat rather than tapered like a flat tappet cam; it is necessary to provide some means of holding the cam back to the rear of the engine. The thrust button rides between the front of the timing gear and the back of the front cover and can be shimmed for proper end play of the cam. COMP Cams has both the solid nylon button and the roller thrust bearing available for the ultimate in performance.

Product Features:

• .810″ Length
• Ride between the front of the timing gear and the back of the timing cover
• Can be shimmed to achieve proper endplay
• Solid nylon and roller thrust bearing styles available

10 Degree Steel Retainer for 26120 Beehive Spring

Edge molded rubber water outlet gasket is reusable, great for engines that require regular disassembling for maintenance. Incorporates solid aluminum carrier for strength and rigidity. Can be used with OE replacement or aftermarket chrome water outlets. Requires no gasket sealer.

Product Features:

• Edge Molded Rubber Water Outlet Gasket Is Reusable
• Requires No Gasket Sealer
• Solid Aluminum Carrier For Strength/rigidity
• Reusable – Ideal for Engines That Are Frequently Taken Apart & Reassembled

Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:

• Precision Machined
• Case Hardened
• Give Accurate Alignment
• 2 Per Set

Product Features:

• Clean Positive Seal
• Embossed Silicone Bead Surrounding The Port
• Matched To Manifolds And Cylinder Heads

This is a high quality bolt set that is made of grade 8 steel and will meet your requirements for a quality bolt set, this set will work on original equipment, high performance street, drag or circle track applications.

Product Features:

• Has A Zinc Dichromate Finish
• Made Of High Quality Grade 8 Steel
• Has A Tall Hex Head To Prevent Wrench Slipping Off
• Extra Thick Parallel Ground Washer
• Washer Provides More Accurate And Uniform Torque

Product Features:

• 50-State Street Legal Aluminum Cylinder Head
• Out-of-the-Box Bolt-On Performance
• 70cc Combustion Chambers Improve Performance
• Retain Stock Compression Ratio

It’s easy to overlook the small details. For engine builders focused on the larger components like camshafts, cylinder heads and pistons, small parts are often forgotten until the final stages of engine assembly. COMP Cams Engine Finishing Kits include those often missing parts like woodruff keys, cylinder head alignment dowels, cam bolts, and timing cover and oil pump dowel pins that are so crucial to properly assembling your engine.

Product Features:

• Includes parts such as woodruff keys, cylinder head alignment dowels, cam bolts, timing cover and oil pump dowel pins
• Available for various engine applications

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.