from

$5.99

Dana 60 pinion gear Thrust washer, standard Open & TracLoc (also 8.75″ Chrysler STD) Dana 70 2PC.

Product Features:

Pinion gear thrust washer for Dana Spicer 60
Fits standard open and Trac Loc applications

from

$198.99

Product Features:

Spider gear kit
Fits Dana Spicer 60, 30 spline open differential
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$42.99

11.5″ Chrysler & GM cover gasket.

Product Features:

Cover gasket
Fits GM and Chrysler 11.5″

from

$31.99

11.5″ GM standard Open side gear Thrust washer.

Product Features:

Side gear thrust washer
Fits GM 11.5″

from

$7.99

Repleacement ring gear bolt for Dana 80. 9/16″ x 18.

Product Features:

Ring gear bolt for Dana Spicer 80
9/16″ x 18 thread

from

$66.99

Dana 70 & Dana 80 standard Open cross pin shaft, one piece case.

Product Features:

Cross pin shaft
Fits Dana Spicer 70 and 80

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$273.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Chrysler 9.25″ front
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$1119.99

Differential

from

$8.29

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$11.29

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$97.99

Product Features:

INSTALL KIT-CHRYSTLER 11.5″

from

$479.99

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

Fits Dana Spicer 70U
Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, oil baffles and slingers , thread locker, marking compound with brush, and gasket.

from

$349.99

Yukon replacement yoke for Dana 80 with a 1550 U/joint size. 4.964″ snap ring span, 1.375″ cap diameter. Outside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

from

$47.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$619.99

Yukon replacement axle for Dana 60, 18.31″ inner, right hand, (15spline disconnect). Yukon front axles come with a one year warranty against manufacturing defects.

Product Features:

15 spline
18.31″ long
Fits Dana Spicer 60 disconnect in 1994-1999 Dodge 3/4 ton and 1 ton
Right hand inner
5-332X U-joint size

from

$16.99

Standard Open cross pin bolt lock ring for 11.5″ GM.

Product Features:

Cross pin bolt lock ring
Fits GM 11.5″

from

$7.99

Replacement pinion nut for Dana 44 JK, 44HD, 60, 70, 70U, 70HD & Nissan Titan rear. 1 5/16″ nut, 7/8″ x 14 thread.

Product Features:

Pinion nut for Jeep JK rear, Dana Spicer 44HD, 60, 70, 70U, 70HD and Nissan Titan rear
7/8″ x 14 thread
1 5/16″ socket

from

$1929.99

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The factory spindles will need to be machined in order to accept the axles this locker uses. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000!

Product Features:

Fits GM and Chrysler 11.5″ with 38 spline axles
Patented internal design reduces common locker failures
8620 internals for added strength
Assembled in the USA

from

$9.99

Product Features:

Preload spacer
Fits Dana Spicer 70

from

$1168.99

Differential

from

$1487.99

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years. This is a narrow case locker. If you have a wide housing, please order two DS 42563 with your locker. This locker is ABS compatible.

Product Features:

Fits Dana Spicer 60 with 35 spline axles
4.56 and up ratio only
Forged case and 8620 internals for added strength
Works with a variety of air delivery systems
Assembled in the USA

from

$72.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$25.99

10.5″ & 11.5″ GM & Dodge pinion seal.Yukon Mighty seal.

Product Features:

Pinion seal
Fits Chrysler 10.5″ and 11.5″

from

$6.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$1037.99

All Spicer ring and pinion gears are designed and tested to meet original equipment specifications. When you purchase genuine Spicer ring and pinion gear sets, you can be confident the ring and pinion set will meet or exceed the exact Dana standards that original equipment manufacturers have relied upon for more than a hundred years.