1998 Dodge Dakota Fluids and Chemicals

Castrol Transmax ATF+4® is a technologically advanced, full synthetic automatic transmission fluid designed for superior transmission life and superb low and high temperature performance. Commonly called ATF4, it is certifi Castrol Transmax ATF+4® is a technologically advanced, full synthetic automatic transmission fluid designed for superior transmission life and superb low and high temperature performance. Commonly called ATF4, it is certified for use in all Fiat Chrysler cars and trucks (License Number: 40630033) that require ATF+4®, ATF+3® or a previous Chrysler transmission specification such as ATF+2®, ATF+2 Type 7176®, or ATF+.

FRAM Chrysler ATF+4 is formulated for Chrysler and DaimlerChrysler transmissions  recommending ATF+4, ATF+3 or ATF+2, and covered by specifications MS-9602 and  MS-7176E/D. FRAM Chrysler ATF+4 fluid is recommended for use in all transmissions,  hydraulic systems, and power steering units manufactured by American, European,  Korean, Japanese and other manufactures from around the world specifying Chrysler  ATF+4, ATF+3 or ATF+2 Type Fluids.

Product Features:

• Excellent flow properties at low start-up temperatures
• Improved shift performance in Chrysler vehicles
• Good viscosity stability
• Excellent oxidation stability
• Rust and corrosion prevention
• Better wear protection for maximum transmission life
• ALWAYS REFER TO YOUR VEHICLES OPERATING MANUAL TO SELECT THE CORRECT GRADE FLUID FOR YOUR TRANSMISSION
• TRANSMISSION FLUIDS ALSO APPLICABLE IN POWER STEERING UNITS; CHECK OWNERS’ MANUAL

Prestone® MAX DOT 3 Motor Vehicle Brake Fluid is our highest grade formula, maximizing performance vs. DOT standard. Prestone MAX is our best brake fluid at protecting against overheating and brake fade. With 100,000 mile fluid life, our longest life fluid has 2X more miles between replacement than regular Prestone DOT 3. Prestone MAX has superior performance in severe braking conditions when compared to regular Prestone DOT 3, which means even more piece of mind about the braking system. This synthetic fluid starts with our highest dry boiling point giving our best protection against performance decline due to water absorption. Prestone MAX DOT 3 is safe to use in all DOT 3 braking systems, ABS, disc or drum, and can mix with any DOT 3 fluid. Mixing Prestone MAX with other fluids will lower the performance rating for miles and boil points, for best results replace completely with Prestone MAX DOT 3. It is recommended to only use the DOT fluid specified for your car. Using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 100,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with Our Highest Grade Formula. Prevents corrosion of all metals within the braking system.
• Superior Protection in Extreme Braking Conditions
• Synthetic, Long Life Formula – 2X Longer than regular Prestone DOT 3

Prestone® DOT 3 Motor Vehicle Brake Fluid delivers enhanced performance vs. DOT standards, benefitting all vehicles calling for DOT 3. This synthetic fluid starts with a higher dry boiling point than the DOT minimum standard to protect against overheating, brake fade and performance decline due to water absorption. This extended life (50,000 mile) fluid is also formulated to prevent corrosion of all metals within the braking system.  This formula is safe to use in all DOT 3 braking systems (ABS, disc or drum) and can mix with any DOT 3 fluid.  It is recommended to only use the DOT fluid specified for your car, as using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 50,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with High Grade Formula*
• Protects against performance decline due to water absorption. Prevents corrosion of all metals within the braking system.
• Synthetic, Extended Fluid Life Formula

Product Features:

• Reduces heat & wear
• Eliminates TQ converter shudder & clutch pack chatter
• For all automatic transmissions & 4×4 transfer cases

Trans Fluid Additive

PENTOSIN ATF 44 5L

Prestone® Power Steering Fluid (PSF) delivers increased system life. Designed with Anti-wear System Protection, Prestone PSF protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 50,000 Mile Fluid Life
• Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber & gasket components.
• For use in all manufacturers
• Conventional Formula – For use in all manufacturers

Only compatible with R134a refrigerant; Tools required for installation; Plastic bottle; Universal applications

High Performance Motor Oil API LICENSED MOTOR OIL Royal Purple High Performance Motor Oil combines premium base oils with proprietary additive technologies to create a high performance synthetic engine oil that optimizes performance and protection. Royal Purple High Performance Motor Oils carry the current API and ILSAC engine oil licenses, as well as the GM dexos1 gasoline engine oil approval. ILSAC GF-6 AND GM DEXOS1 Modern gasoline direct injection (GDI) engines have achieved levels of power and fuel economy never before possible in passenger car engines. As a result, smaller engines operate at much higher loads across all engine speeds. This has caused increased wear in critical areas of the engine, and created a destructive phenomenon called low-speed pre-ignition (LSPI). The unique, state-of-the-art additive technology in Royal Purple High Performance engine oils is designed specifically to address these issues, and help engines maintain performance and reliability.

Product Features:

• Better Wear Protection
• Increased Protection against Low Speed Pre-Ignition
• Increased Fuel Efficiency
• Better Protection for Vehicle Exhaust Emissions Equipment
• Improved Compatibility with Fuels Containing Ethanol
• Superior Corrosion Protection
• Made in USA

Valvoline SAE 75W-140 Full Synthetic Gear Oil provides the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Engineered to outperform, our formulation provides exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity and wear resistance, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. It’s recommended for conventional rear axles and transmissions requiring EP gear lubes under high speed, high load, high torque and high horsepower conditions.

Product Features:

• EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -22F to 390F degrees
• REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
• FIGHTS CORROSION AND RUST with emulsifying agents and safeguards against impurities, oxidation and thermal breakdown
• MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-3
• MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Ford M2C-192A, GM 12346140, Chrysler MS-8985 and API GL-4

Valvoline SAE 75W-140 Full Synthetic Gear Oil provides the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Engineered to outperform, our formulation provides exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity and wear resistance, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. It’s recommended for conventional rear axles and transmissions requiring EP gear lubes under high speed, high load, high torque and high horsepower conditions.

Product Features:

• EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -22F to 390F degrees
• REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
• FIGHTS CORROSION AND RUST with emulsifying agents and safeguards against impurities, oxidation and thermal breakdown
• MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4
• MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Ford M2C-192A, GM 12346140, Chrysler MS-8985 and API GL-5

Certified A/C Pro R-134a PAG 46 Refrigerant Oil with ICE 32. This product contains approximately 8 fluid ounces of PAG refrigerant oil with ICE32. Low viscosity PAG oil for R-134a auto A/C systems; ISO 46 viscosity. R-134a PAG 46 AC Oil Lubricant: with ICE 32 Lubricant Enhancer features advanced chemistry to help extend compressor life and improve cooling capacity. The PAG oil helps quiet noisy compressors. Meets OEM specifications.

Product Features:

• Low viscosity PAG oil for R-134a auto A/C systems; ISO 46 viscosity
• ICE32 Lubricant Enhancer: advanced chemistry to help extend compressor life and improve cooling capacity
• Meets OEM specifications

Certified A/C Pro R-134a PAG 100 Refrigerant Oil with ICE 32. This product contains approximately 8 fluid ounces of PAG refrigerant oil with ICE32. Medium viscosity PAG oil for R-134a auto A/C systems; ISO 100 viscosity. R-134a PAG 100 AC Oil Lubricant with ICE32 Lubricant Enhancer features advanced chemistry to help extend compressor life and improve cooling capacity. The PAG oil helps quiet noisy compressors. Meets OEM specifications.

Product Features:

• Medium viscosity PAG oil for R-134a auto A/C systems; ISO 100 viscosity
• ICE32 Lubricant Enhancer: advanced chemistry to help extend compressor life and improve cooling capacity
• Meets OEM specifications

Only compatible with R134a refrigerant; Tools required for installation; Plastic bottle; Universal applications

Valvoline ATF+4® is a full-synthetic transmission fluid specifically engineered to protect and prolong the life of (FCA) Fiat Chrysler automatic transmissions. It is officially licensed and approved by FCA and is fully back-serviceable and can be used wherever ATF+3, ATF+2 or ATF+ is specified. Recommended for use in the following applications: Mopar ATF+ MS 7176®, ATF+2® MS 7176, ATF+3 and ATF+4.

Product Features:

• Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Valvoline DEX/MERC ATF is a high-quality transmission fluid formulated to meet the challenging demands many automatic transmissions. Its responsive low-temperature fluidity is beneficial in both electronic and hydraulic controlled transmissions and transaxles. Recommended for use in the following applications: MERCON®, DEXRON®-III, Ford M2C138-CJ and M2C166-H, Allison C-4 and TES-389, and Caterpillar TO-2.

Product Features:

• Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• Maxlife technology prevents engine breakdown with 40% better wear protection than the industry standard
• Refresh aging seals and prevent leaks with seal conditioners
• Reduce sludge, deposits, corrosion, and rust with added detergents – keep motors clean inside
• Enhanced friction performance helps maximize power with advanced friction-fighting agents
• Meets or exceeds all requirements of ilsac gf-6a, api sp, api sn with sn plus, api sn
• Synthetic Blend: Our unique combination of synthetic and premium conventional oils provides superior protection against wear, friction, heat, and deposits.

Help keep positraction chatter down with posi additive from Yukon Gear & Axle.

Product Features:

• positraction additive
• For use in any clutch-style limited slip

Crown Automotive continues to be the leader in quality replacement parts for Jeep(R) vehicles. Crown has the largest stock of replacement parts for Jeep(R) vehicles, including factory discontinued parts. In fact, many of the older Jeeps are still on (and off) the road thanks to Crown parts. The Crown line consists of axle, body, brake, clutch, cooling, driveline, electrical, engine, exhaust, fuel, steering, suspension, transmission And transfer case components. Crown Automotive also offers an exclusive line of component kits And accessory products.

Product Features:

• Limited 12 Month Or 12,000 Mile Warranty

3 oz. tube, carded – OEM specified. Specially formulated to withstand the harsh gear oil environment found in differentials and transfer cases. Because gear oil has friction modifiers that break down normal RTV and cause leaking, this specialty silicone has been tested to OEM specifications to ensure complete sealing. As a gasket maker, it seeks and seals leak paths that cut gaskets cannot. It can also be used to seal cut gaskets. Suggested Applications: Differentials and transfer cases. DIRECTIONS:

Product Features:

• For best results, clean and dry all surfaces with a residue-free solvent, such as Permatex® Brake and Parts Cleaner.
• Cut nozzle to desired bead size: gaskets are best formed using a 1/16? to 1/4? (2 to 6 mm) bead.
• Apply a continuous and even bead of silicone to one surface; surround all bolt holes. Assemble parts immediately. Finger tighten bolts until material begins to squeeze out around flange. Allow to dry for one hour then re-tighten 1/4 to 1/2 turn.
• Silicone dries in 1 hour, and fully cures in 24 hours. Allow more time in cold or very dry conditions.
• Replace cap after use. Note: Not recommended for use on head gaskets or parts in contact with gasoline. Store below 80°F (27°C). TECHNICAL DATA SHEET

PEAK ORIGINAL EQUIPMENT TECHNOLOGY ANTIFREEZE + COOLANT for NORTH AMERICAN VEHICLES is a line of premium coolants specifically designed to match the technology and color requirements of North American vehicles. Each coolant is formulated with the same corrosion inhibitor technology that protected your vehicle straight from the factory. Color cues on the packaging and a list of covered vehicles on the front label make it easy to identify the right match for your specific vehicle. PEAK ORIGINAL EQUIPMENT TECHNOLOGY ANTIFREEZE + COOLANT for NORTH AMERICAN VEHICLES – GOLD is an extended life antifreeze/coolant based on proprietary hybrid organic acid technology (HOAT). The ethylene glycol-based formula combines a mixture of organic acid corrosion inhibitors, stabilized silicate and a nitrite/nitrate combination to provide complete corrosion protection to both gasoline and diesel engines. Its low silicate formula with deposit control additives protects against wet sleeve liner cavitation and scale formation. This product’s gold color distinguishes its unique chemistry and ensures easy selection for Ford and Chrysler vehicles requiring this type of technology and coolant color. PEAK ORIGINAL EQUIPMENT TECHNOLOGY ANTIFREEZE + COOLANT for NORTH AMERICAN VEHICLES – GOLD is free of phosphate, amines and 2-ethyl hexanoic acid (2-EHA) and is safe for non-metallic cooling system components. It is fully compatible with other gold hybrid coolants and meets the performance requirements of ASTM D3306, D4985 and D6210. With a complete flush and fill, PEAK guarantees this coolant will provide the service life specified by the OEMs utilizing this specific technology, typically up to 5 years or 150,000 miles.

Product Features:

• Matches technology and color requirements of North American OEMs specifying a Green Conventional coolant
• Protects all cooling system metals, including aluminum, against damaging rust and corrosion
• Compatible with other conventional green antifreeze + coolant formulations
• Easy-to-pour bottle with color-coding and vehicle applications listed on the front to simplify selecting the right antifreeze + coolant
• Available as both concentrate and 50/50 prediluted products to do the job right
• Testing Requirements: For proper freeze and boil over protection, use a traditional refractometer or hydrometer to measure the percentage of ethylene glycol by volume.

Prestone All Vehicles antifreeze+coolant (ready to use) is truly designed to work with all vehicles; all makes, models, years & fluid colors. It is designed to work with all new engines while also being backwards compatible improving protection in all older engines. The patented Cor-Guard technology (the best innovation in the category in decades) instantly protects parts from corrosion, buildup, pitting, scaling, rust and other damage. These fluids are specially designed to not only manage the engine temp and protect from freezing up (like competitors), but they also potect the engine from damage. Internal damage can cause engine part failure, leading to expensive repairs and serious inconveniences. Avoid costly repairs and vehicles in the shop with Prestone All Vehicles antifreeze+coolant. This fluid is designed to last 10yrs / 300,000 miles and also to protect the internal parts of the engine for 10yrs / 300,000, offically patented by Prestone.

Product Features:

• Formulated to work with All Vehicles. Works with all fluid colors; All OAT, POAT, HOAT & IAT.
• Longer Engine Life Guarantee – 10 Yr., 300,000 mile Extended life formula.
• Includes patented Prestone CorGuard technology, the best advancement in cooling system parts protection that protects against rust and corrosion of all cooling system metals, including aluminum. Protection for 300,000 miles.
• Ready to Use formula (prediluted to a 50% Eg & 50% distilled water mix). Perfect for small volume top-off or complete drain and refill of the cooling system

All Anitfreeze + Coolants are not the same. Prestone® MAX antifreeze + coolant is GUARANTEED to provide MAXIMUM ENGINE PROTECTION in all Vehicle Makes, Models & Years. It delivers the widest range of temperature protection, industry leading protection from engine damaging rust & corrosion and the longest lasting protection in the industry. Trust Prestone for maximum, year-round engine protection.

Product Features:

• Can top off or replace all antifreeze + coolant colors and formulations in all Vehcile Makes, Models & Years – Guaranteed.
• Our patented, advance formula provides extreme temperature protection from the worst of winter deep freezes and scorching summer heat.
• We deliver industry leading protection from engine damaging rust, corrosion & buildup. Prestone MAX completely stops the formation of rust & corrosion for better engine performance and longer engine life.
• Prestone Max is guaranteed to protect your vehicle for 15+ years and/or 350,000 miles. It¿s the longest fluid life in the industry.
• Prestone Max is guaranteed to protect your vehicle for 15+ years and/or 350,000 miles. It┐s the longest fluid life in the industry.
• This is a Concentrated Formula. Must mix with high quality water to the desired ratio.

Prestone All Vehicles antifreeze+coolant (concentrate) is truly designed to work with all vehicles; all makes, models, years & fluid colors. It is designed to work with all new engines, while also being backwards compatible improving protection in all old

Product Features:

• Formulated to work with All Vehicles. Works with all fluid colors; All OAT, POAT, HOAT & IAT.
• Longer Engine Life Guarantee – 10 Yr., 300,000 mile Extended life formula.
• Includes patented Prestone CorGuard technology, the best advancement in cooling system parts protection that protects against rust and corrosion of all cooling system metals, including aluminum. Protection for 300,000 miles.
• Concentrate formula. Must mix with distilled to the desired mix ratio of EG & water. Can be used for top-off, complete drain and refill or flush and refill of the cooling system.

FRAM Conventional Green Concentrate is an ethylene glycol-based product for use in car and light duty trucks that are already using a conventional coolant. The inhibitors prevent rust, corrosion, and provide freezeup and boil-over protection. When used as directed, the Prime Green Concentrate Low Silicate formula provides full protection for a minimum of one year.

Product Features:

• Low Silicate Formula
• When used as directed, will provide protection for a minimum of 1 year
• Meets or exceeds ASTM requirements for cars, light duty trucks
• Concentrated formula. Must mix with high quality (distilled/deionized) water to the desired ratio. Can be used for top-off, complete drain and refill or flush and refill of the cooling system.

Prestone American Vehicles (Orange) antifreeze+coolant is specially designed to work with these specific vehicles: Ford 2002 and newer; Chrysler 2000 and newer; GM 1995 and newer. Prestone’s Antifreeze+Coolants are designed to the highest standards using state of the art technology. These fluids are designed to not only manage the engine temp and protect from freezing up, but they also protect the engine from rust, corrosion, buildup, pitting and engine damage. All of those can cause engine part failure and expensive repairs. Avoid costly repairs and vehicles in the shop with Prestone Asian vehicles antifreeze+coolant. This fluid is designed to last 10yrs / 300,000 miles and also to protect the internal parts of the engine for 10yrs / 300,000, offically patented by Prestone.

Product Features:

• Specially formulated to work with vehicles using multiple colors of fluid; OAT, HOAT, G05. Ford 2002 and newer; Chrysler 2000 and newer; GM (Chevrolet, Buick, GMC, Cadillac, Oldmobile, Pontiac, Saturn) 1995 and newer.
• Superior protection guarantee – 10 Yr., 300,000 mile Extended life formula
• Includes patented Prestone CorGuard technology, the best advancement in cooling system parts protection that protects against rust and corrosion of all cooling system metals, including aluminum. Protection for 300,000 miles.
• Ready to Use formula. Perfect for small volume top-off or complete drain and refill of the cooling system.

FRAM Orange Concentrate is formulated for cars and light duty trucks that use Orange extended life coolant. Prime Orange Concentrate meets or exceeds ASTM D3306 and D4985 standards for corrosion protection, while providing reliable freeze-up and boil-over protection.

Product Features:

• Work with vehicles using orange colored fluid. 5 Yr., 150,000 mile Extended life formula
• All GM® vehicles 1995 & newer /GM approved (GMC, Chevrolet, Buick, Cadillac, Pontiac, Saturn, Oldsmobile, Hummer), most Ford® vehicles 2011- 2018 (Ford, Lincoln, Mercury) and most Chrysler® vehicles 2013 & newer (Ram, Dodge, Jeep, Chrysler)
• Meets or exceeds ASTM D3306 & D4985 for corrosion protection.
• Concentrated formula. Must mix with high quality (distilled/deionized) water to the desired ratio. Can be used for top-off, complete drain and refill or flush and refill of the cooling system.