from

$45.99

Synthetic technology low-friction motor oil with the latest wear-protection technology and extremely high power reserve for maximum performance. Good dirt suspending and cleaning capacity ensures optimum engine cleanliness. Assures reliable operation and maximizes the operating life of the diesel particulate filter (DPF). Exceeds the highest test requirements of well-known vehicle manufacturers.An all-season oil for gasoline and diesel engines including common rail technology. Particularly suited for vehicles with a diesel particulate filter (DPF), also for retrofits.

Product Features:

Modern premium low friction engine oil
All season use reliable at high and low temperatures
Provides exceptional protection against wear
Reduces oil and fuel consumption
Ensures fast oil penetration of the engine
Made in germany

from

$31.99

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

MAXLIFE TECHNOLOGY PREVENTS engine breakdown with 40% better wear protection than the industry standard
REFRESH AGING SEALS AND PREVENT LEAKS with seal conditioners
REDUCE SLUDGE, DEPOSITS, CORROSION, AND RUST with added detergents – keep motors clean inside
ENHANCED FRICTION PERFORMANCE HELPS MAXIMIZE POWER with advanced friction-fighting agents
MEETS OR EXCEEDS ALL REQUIREMENTS of ILSAC GF-6A, API SP, API SN with SN PLUS, API SN

from

$85.99

PENTOSIN ATF 44 5L

from

$13.49

Only compatible with R134a refrigerant; Tools required for installation; Plastic bottle; Universal applications

from

$13.49

Certified A/C Pro R-134a PAG 46 Refrigerant Oil with ICE 32. This product contains approximately 8 fluid ounces of PAG refrigerant oil with ICE32. Low viscosity PAG oil for R-134a auto A/C systems; ISO 46 viscosity. R-134a PAG 46 AC Oil Lubricant: with ICE 32 Lubricant Enhancer features advanced chemistry to help extend compressor life and improve cooling capacity. The PAG oil helps quiet noisy compressors. Meets OEM specifications.

Product Features:

Low viscosity PAG oil for R-134a auto A/C systems; ISO 46 viscosity
ICE32 Lubricant Enhancer: advanced chemistry to help extend compressor life and improve cooling capacity
Meets OEM specifications

from

$96.99

FRAM DEX III/MERC ATF is formulated for older model Ford and General Motors vehicles requiring MERCON®, DEXRON-I®, DEXRON-II® and DEXRON-III®. It is also recommended for transmissions, power steering systems, and hydraulic systems requiring a DEXRONIII® or Caterpillar TO-2 fluid. FRAM DEX III/MERC ATF may also be used in compressors, pumps, and hydraulic systems. FRAM DEX III-H/M ATF is recommended for use in all transmissions, hydraulic systems, and power steering units manufactured by American, European, Korean, Japanese and other manufactures from around the world specifying DEXRON®III H/Mercon® and earlier DEXRON®/Mercon® type transmission fluids.

Product Features:

Good foam and corrosion prevention
Safe for seals
Promotes smooth shifting
ALWAYS REFER TO YOUR VEHICLES OPERATING MANUAL TO SELECT THE CORRECT GRADE FLUID FOR YOUR TRANSMISSION
TRANSMISSION FLUIDS ALSO APPLICABLE IN POWER STEERING UNITS; CHECK OWNERS’ MANUAL

from

$25.99

Castrol Transmax ATF/CVT Universal is a technologically advanced full-synthetic formulation designed to deliver excellent performance in most of the traditional stepped automatic transmissions and Continuously Variable Transmissions currently in use. It is also suitable for use in hybrids.

Product Features:

Coverage of over 300 specs/95% of vehicles in operation
Broad scope of vehicle applications improves workshop efficiency and inventory management
Enhanced friction durability for smooth transmission performance
Superior high temperature protection to effectively resist oxidation

from

$8.79

FRAM DEX III/MERC ATF is formulated for older model Ford and General Motors vehicles requiring MERCON®, DEXRON-I®, DEXRON-II® and DEXRON-III®. It is also recommended for transmissions, power steering systems, and hydraulic systems requiring a DEXRONIII® or Caterpillar TO-2 fluid. FRAM DEX III/MERC ATF may also be used in compressors, pumps, and hydraulic systems. FRAM DEX III-H/M ATF is recommended for use in all transmissions, hydraulic systems, and power steering units manufactured by American, European, Korean, Japanese and other manufactures from around the world specifying DEXRON®III H/Mercon® and earlier DEXRON®/Mercon® type transmission fluids.

Product Features:

Good foam and corrosion prevention
Safe for seals
Promotes smooth shifting
ALWAYS REFER TO YOUR VEHICLES OPERATING MANUAL TO SELECT THE CORRECT GRADE FLUID FOR YOUR TRANSMISSION
TRANSMISSION FLUIDS ALSO APPLICABLE IN POWER STEERING UNITS; CHECK OWNERS’ MANUAL

from

$14.29

Mobil 1 Synthetic ATF is a multi-vehicle, fully synthetic automatic transmission fluid that helps to improve overall transmission durability and cleanliness. Has exceptional thermal and oxidation stability and long-term frictional properties that help to improve and extend transmission efficiency, smooth shifting performance, and fuel economy. Mobil 1 ATF provides excellent low-temperature fluidity to promote reliable lubrication at temperatures down to -51C, and exceptional shear stability to help supports viscosity retention under the most severe heavy-duty, high-temperature operating conditions. Compatibile with mineral ATF fluids and all common seal materials to help provide excelent leakage control and reduce concern in top-off emergencies. Meets or exceeds the requirements of JASO 1-A and Ford MERCON V.

Product Features:

Multi-vehicle, fully synthetic automatic transmission fluid that helps to improve overall transmission durability and cleanliness
Exceptional thermal and oxidation stability to improve and extend transmission efficiency, smooth shifting performance, and fuel economy
Excellent high and low-temperature fluidity to help support viscosity retention under extreme, heavy-duty operating conditions
Compatibile with mineral ATF fluids and all common seal materials to help provide excelent leakage control
Meets or exceeds the requirements of JASO 1-A and Ford MERCON V
Manufacturer Part Number: 112980

from

$38.49

Valvoline DEXRON-VI/MERCON LV ATF is a full-synthetic transmission fluid formulated with advanced additive technology to meet and exceed the requirements of the General Motors DEXRON-VI specification. It is officially licensed and approved by GM and is fully back-serviceable and can be used wherever DEXRON-II and/or DEXRON-III are recommended. Recommended for use in the following applications: DEXRON-VI, DEXRON-III, DEXRON-II, MERCON LV and Allison C-4.

Product Features:

Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$5.99

Prestone® DOT 3 Motor Vehicle Brake Fluid delivers enhanced performance vs. DOT standards, benefitting all vehicles calling for DOT 3. This synthetic fluid starts with a higher dry boiling point than the DOT minimum standard to protect against overheating, brake fade and performance decline due to water absorption. This extended life (50,000 mile) fluid is also formulated to prevent corrosion of all metals within the braking system. This formula is safe to use in all DOT 3 braking systems (ABS, disc or drum) and can mix with any DOT 3 fluid. It is recommended to only use the DOT fluid specified for your car, as using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

50,000 Mile Fluid Life
Prevent Overheating & Brake Fade with High Grade Formula*
Protects against performance decline due to water absorption. Prevents corrosion of all metals within the braking system.
Synthetic, Extended Fluid Life Formula

from

$12.49

Prestone® MAX DOT 3 Motor Vehicle Brake Fluid is our highest grade formula, maximizing performance vs. DOT standard. Prestone MAX is our best brake fluid at protecting against overheating and brake fade. With 100,000 mile fluid life, our longest life fluid has 2X more miles between replacement than regular Prestone DOT 3. Prestone MAX has superior performance in severe braking conditions when compared to regular Prestone DOT 3, which means even more piece of mind about the braking system. This synthetic fluid starts with our highest dry boiling point giving our best protection against performance decline due to water absorption. Prestone MAX DOT 3 is safe to use in all DOT 3 braking systems, ABS, disc or drum, and can mix with any DOT 3 fluid. Mixing Prestone MAX with other fluids will lower the performance rating for miles and boil points, for best results replace completely with Prestone MAX DOT 3. It is recommended to only use the DOT fluid specified for your car. Using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

100,000 Mile Fluid Life
Prevent Overheating & Brake Fade with Our Highest Grade Formula. Prevents corrosion of all metals within the braking system.
Superior Protection in Extreme Braking Conditions
Synthetic, Long Life Formula – 2X Longer than regular Prestone DOT 3

from

$18.99

FRAM Conventional Green Concentrate is an ethylene glycol-based product for use in car and light duty trucks that are already using a conventional coolant. The inhibitors prevent rust, corrosion, and provide freeze-up and boil-over protection. When used as directed, the Prime Green Concentrate Low Silicate formula provides full protection for a minimum of one year.

Product Features:

Low Silicate Formula
When used as directed, will provide protection for a minimum of 1 year
Meets or exceeds ASTM requirements for cars, light duty trucks
Concentrated formula. Must mix with high quality (distilled/deionized) water to the desired ratio. Can be used for top-off, complete drain and refill or flush and refill of the cooling system.

from

$22.99

ZEREX Asian Vehicle Antifreeze/Coolant is specifically formulated to meet the requirements of Asian vehicle manufacturers (Toyota®, Lexus®, Scion® and others) requiring a red, silicate free Hybrid Organic Acid Technology (HOAT) with a phosphate additive. This patented formula is designed to replace the original fluid and provides protection from rust, corrosion, boil overs and freezing.

Product Features:

Formulated to replace the OEM fluid in Asian make vehicles such as Toyota®, Lexus®, Scion® and others requiring a red, silicate free HOAT antifreeze/coolant
Silicate-free, long-life, phosphate Hybrid Organic Acid Technology chemistry
The long life formula provides protection for all cooling system metals from rust and corrosion. The silicate free, borate free formula helps protect against harmful scale and deposits
Meets the following OEM and industry specifications: JIS K 2234-1994, Hyundai/KIA MS 591-08, Mitsubishi ES-64217, Ford WSS-M97B55-A, ASTM 3306, ASTM D4985, Federal Specification A-A-870A

from

$18.99

All Anitfreeze + Coolants are not the same. Prestone® MAX antifreeze + coolant is GUARANTEED to provide MAXIMUM ENGINE PROTECTION in all Vehicle Makes, Models & Years. It delivers the widest range of temperature protection, industry leading protection from engine damaging rust & corrosion and the longest lasting protection in the industry. Trust Prestone for maximum, year-round engine protection.

Product Features:

Can top off or replace all antifreeze + coolant colors and formulations in all Vehcile Makes, Models & Years – Guaranteed.
Our patented, advance formula provides extreme temperature protection from the worst of winter deep freezes and scorching summer heat.
We deliver industry leading protection from engine damaging rust, corrosion & buildup. Prestone MAX completely stops the formation of rust & corrosion for better engine performance and longer engine life.
Prestone Max is guaranteed to protect your vehicle for 15+ years and/or 350,000 miles. It¿s the longest fluid life in the industry.
Prestone Max is guaranteed to protect your vehicle for 15+ years and/or 350,000 miles. It┐s the longest fluid life in the industry.
This is a Concentrated Formula. Must mix with high quality water to the desired ratio.

from

$15.99

Antifreeze Conventional Green 50/50 is an ethylene glycol-based product for use in car and light duty trucks that are already using a conventional coolant. The inhibitors prevent rust, corrosion, and provide freeze-up and boil-over protection. Prime Green 50/50 can be used to top-off cooling systems in vehicles using conventional AF/C, will not harm rubber parts, and meets ASTM D3306 and D4985 standards.

Product Features:

Low Silicate Formula.
When used as directed, will provide protection for a minimum of 1 year
Meets or exceeds ASTM requirements for cars, light duty trucks
Ready to Use formula (prediluted to a 50% Eg & 50% distilled water mix). Perfect for small volume top-off or complete drain and refill of the cooling system

from

$10.49

Prestone® Power Steering Fluid + Stop Leak (PSF+SL) delivers increased system life and prevents & stops system leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. The stop leak additives also prevent leaks by rejuvenating seals before they leak. Also designed with Anti-wear System Protection, Prestone PSF+SL protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

50,000 Mile Fluid Life
Includes Stop Leak Additives to prevent and stop power steering system leaks.
Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber & gasket components.
Conventional Formula – For use in all manufacturers

from

$9.99

Prestone® Power Steering Fluid (PSF) delivers increased system life. Designed with Anti-wear System Protection, Prestone PSF protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

50,000 Mile Fluid Life
Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber & gasket components.
For use in all manufacturers
Conventional Formula – For use in all manufacturers

from

$6.26

Power Steering Fluid

from

$14.99

Prestone® MAX American Vehicles Power Steering Fluid (PSF) + Stop Leak maximizes and increases system life + the power to stop leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. This formula is also great at preventing leaks by rejuvenating seals before they leak. This synthetic fluid is designed with 2X Anti-wear System Protection, which means more protection against pump failure, squeals and clogs. 100,000 mile fluid life, 2X more than conventional fluid, extends the time between replacement. This fluid is formulated for American vehicle manufacturers: Ford, Lincoln, Mercury, Dodge, Ram, Jeep, Chrysler, GMC, Chevrolet, Buick, Cadillac, Pontiac, Oldsmobile and others. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

100,000 Mile Fluid Life. Synthetic Formula for longer life and more protection
MAX + Stop Leak. Stop Leak Additives to prevent and stop power steering system leaks.
For use in American vehicle manufacturers: Ford, Lincoln, Mercury, Dodge, Ram, Jeep, Chrysler, GMC, Chevrolet, Buick, Cadillac, Pontiac, Oldsmobile and other
2X Anti-Wear Protection for enhanced System Life vs. conventional fluid. More protection against pump failure, squeals and clogs

from

$18.99

We’ve squeezed innovation into every ounce of Valvoline FlexFill SAE 75W-90 Full Synthetic Gear Oil, the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Our unique new flexible pouch makes getting into the tightest places to lubricate gears easier than ever and with less waste. The superior detergent package-based formulation contains fully synthetic basestocks and special additives that help protect parts from rust and corrosion while providing exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity, wear resistance additives that assist in protecting gear teeth, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. Valvoline FlexFill SAE 75W-90 Full Synthetic Gear Oil is recommended for use in axle applications requiring factory-fill or drain-and-fill levels for limited slip performance.

Product Features:

FLEXIBLE POUCH FOR EASIER USE WITH LESS WASTE in tight, hard to reach undercarriage situations
EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -30F to 300F degrees for dependable coverage year-round
REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4 or MT-1 fluid
MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Mack GO-H and GO-J; API GL-5 and API MT-1; MIL-PRF-2105E; and SAE J2360

from

$10.29

Formulated to meet the specific requirements of Subaru vehicles equipped with conventional (non-CVT) transmissions up to model year 2005. Recommended for service-fill in all Subaru automatic transmissions where SUBARU ATF HP is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. IDEMITSU is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. IDEMITSU application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.

Product Features:

Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
Provides superior cleanliness, maintaining the transmission free of sludge and varnish deposits
Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
Advanced anti-wear technology provides maximum protection to gears and bearings

from

$19.99

We’ve squeezed innovation into every ounce of Valvoline FlexFill SAE 75W-140 Full Synthetic Gear Oil, the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Our unique new flexible pouch makes getting into the tightest places to lubricate gears easier than ever and with less waste. The superior detergent package-based formulation contains fully synthetic basestocks and special additives that help protect parts from rust and corrosion while providing exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity, wear resistance additives that assist in protecting gear teeth, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. Valvoline FlexFill SAE 75W-140 Full Synthetic Gear Oil is recommended for use in axle applications requiring factory-fill or drain-and-fill levels for limited slip performance.

Product Features:

FLEXIBLE POUCH FOR EASIER USE WITH LESS WASTE in tight, hard to reach undercarriage situations
EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -30F to 300F degrees for dependable coverage year-round
REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4
MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Ford M2C-192A, GM 12346140, Chrysler MS-8985 and API GL-5

from

$35.99

Valvoline DEX/MERC ATF is a high-quality transmission fluid formulated to meet the challenging demands many automatic transmissions. Its responsive low-temperature fluidity is beneficial in both electronic and hydraulic controlled transmissions and transaxles. Recommended for use in the following applications: MERCON®, DEXRON®-III, Ford M2C138-CJ and M2C166-H, Allison C-4 and TES-389, and Caterpillar TO-2.

Product Features:

Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$13.99

Valvoline Import Multi-Vehicle Automatic Transmission Fluid is specifically formulated for use in most Toyota, Nissan, Honda and other imported vehicles. It is formulated with all synthetic base stocks and a proprietary additive system to ensure optimal transmission performance in a wide variety of vehicles. Valvoline Import Multi-Vehicle ATF can also be used in many domestic vehicles. It meets requirements of General Motors and Ford vehicles. Recommended for use in the following applications: Ford MERCON®, GM DEXRON®-II and DEXRON®-III, BMW LT 71141 and ETL-7045E, Nissan/Infiniti Nissan ATF, Matic-D, Matic-K and Matic-J, Mitsubishi Diamond SP-II and SP-III, Subaru ATF-HP, Hyundai/ KIA SP-II and SP-III , Toyota/Lexus Type T, T-III and T-IV , Honda/Acura ATF-Z1 (except in CVTs) , Mercedes Benz NAG1 , Volvo passenger car (except AW-1), and Volkswagen/Audi TL52162. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.

Product Features:

Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

1996 Infiniti J30 Fluids and Chemicals

More 1996 Infiniti J30 Fluids and Chemicals Categories

Essential 1996 Infiniti J30 Fluids and Chemicals

LIQUI MOLY – Longtime High Tech Full Synthetic 5W-30 Engine Oil: Wear Protection, Maximum Performance, 5 Liter (Part No.2039)

Valvoline – High Mileage with MaxLife Technology Synthetic Blend 5W-30 Motor Oil: Maximize Engine Life, 5 Quart (Part No.782256)

Pentosin – PENTOSIN ATF 44 5L (Part No.1058212)

Factory Air – 8 oz. Bottle Premium PAG 46 Oil w/o Dye (Part No.59007)

Certified A/C Pro – R-134a PAG 46 AC Oil Lubricant: With ICE 32 For Improved Cooling, 8 oz (Part No.GPL-5)

FRAM – Dexron III / Mercon Multi-Vehicle Automatic Transmission Fluid: 5 Gallon (Part No.F420-5)

Castrol – Transmax ATF / CVT Universal Automatic Transmission Fluid, 1 Gallon (Part No.15E0C8)

FRAM – Dexron III / Mercon Multi-Vehicle Automatic Transmission Fluid: 1 Quart (Part No.F420)

Mobil 1 – Full Synthetic Automatic Transmission Fluid, 1 Quart (Part No.25201)

Valvoline – DEXRON®-VI ATF Full Synthetic Automatic Transmission Fluid, 1 Gallon (Part No.883572)

Prestone – DOT 3 Brake Fluid: Synthetic, Prevents Corrosion, Safe For ABS, Disc, Drum Brakes, 50k miles, 12 oz (Part No.AS400)

Prestone – DOT 3 Brake Fluid: MAX Synthetic, Highest Grade, Superior Protection, 100k miles, 32 oz (Part No.AS410)

FRAM – Antifreeze & Coolant: Concentrate, Conventional Green, 1 Gallon (Part No.F101)

ZEREX – Asian Vehicle Red 50/50 Ready-to-Use Antifreeze / Coolant, 1 Gallon (Part No.675130)

Prestone – MAX Antifreeze + Coolant: All Vehicles, Concentrate, 1 Gallon (Part No.AF2800)

FRAM – Heavy Duty Antifreeze and Coolant: 50/50 Ready To Use, Universal , 1 Gallon (Part No.F201)

Prestone – Power Steering Fluid: All Vehicles, With Stop Leak, Restores & Conditions Seals, 50k miles, 32 oz (Part No.AS263Y)

Prestone – Power Steering Fluid: All Vehicles, Anti-Wear Protection, 50k miles, 32 oz. (Part No.AS261Y/1)

Idemitsu Lubricants – Power Steering Fluid (Part No.3J100424800IDE)

Prestone – MAX Power Steering Fluid: American Vehicles, With Stop Leak, Enhances System Life, 100k miles, 12 oz (Part No.AS277)

Valvoline – Flex Fill Transmission & Differential Gear Oil: Full Synthetic 75W-90, 1 Quart (Part No.889785)

Idemitsu – Type HP Automatic Transmission Fluid – 1 qt (Part No.10107-042F)

Valvoline – Flex Fill Transmission & Differential Gear Oil: Full Synthetic 75W-140, 1 Quart (Part No.889787)

Valvoline – DEX/MERC Automatic Transmission Fluid, 1 Gallon (Part No.773636)

Valvoline – Import Multi-Vehicle Synthetic Automatic Transmission Fluid, 1 Quart (Part No.822389)

Popular 1996 Infiniti J30 Fluids and Chemicals Categories

1996 Infiniti J30 Fluids and Chemicals

Top-Rated Fluids and Chemicals Brands For Your 1996 Infiniti J30

Popular Castrol Fluids and Chemicals

Top-Rated Valvoline Fluids and Chemicals

FAQs for 1996 Infiniti J30 Fluids and Chemicals

What are the most purchased Fluids and Chemicals for the 1996 Infiniti J30?

What are the top-rated 1996 Infiniti J30 Fluids and Chemicals?

More Popular Parts for All Makes