1994 Ford Bronco Performance and Racing Products

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• PTFE offers the best in fluid and high-temperature compatibility and contact sealing surface can run on undersize shafts, seal minor imperfections and virtually eliminate shaft wear.
• Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
• Not intended for use in emission controlled vehicles.

For the person who wants a subtle custom appearance with all the benefits that a Flowmaster Cat-back exhaust system provides. S.O.S. (Single out side) systems are the perfect choice. Force II systems delivers a mild exterior tone and moderate to mild interior tone, and are suited to customers looking for efficiency improvements without a lot of noise. Especially recommended for towing applications. Like all Flowmaster systems, the benefits include improved throttle response, power and mileage. Designed for an easy fit, these systems include all necessary parts and hardware for easy installation.

MSD Ignition is a company built on Customer Satisfaction and Service. That is why all of MSD products go through regimented test procedures before they are ever packaged and shipped. MSD stands behind its products for one full year after purchase

Product Features:

• Rotor phasing can be adjusted.
• Ideal When Atomic TBI Is Controlling The Timing

Product Features:

• Non-Rotator Type
• 1.384 in. Outer Diameter
• 1.020 in. Inner Diameter
• 1.020 in. Coil Blind
• Set of 16

Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provi

Product Features:

• PerTronix D4062 Flame-Thrower HEI Distributor Rotor Blue
• Made from hi-performance 60 KV rated alkyd molding compound.

The Monro-Magnum® steering stabilizer stops vibration before it gets to the driver. Acting as a horizontal shock absorber, Monro-Magnum® steering stabilizers help reduce vibrations that travel through the steering system to the driver.

Product Features:

• 1/2 inch Piston Rod Heavy-duty nitrocarburized rod for long service life
• All Weather Fluid Contains special modifiers to reduce friction and ensure smooth rod reaction.
• Full Displaced Valving Better valving range on both the compression and extension cycles of the unit for a smooth comfortable ride.
• Micro-Cellular Gas Design Allows unit to be mounted horizontally.
• Sintered Iron Piston Stronger than traditional metals, enhances durability for longer service life.
• Special Seal ‘Self-lubricating’ fluid seal designed to retain gas without excessive wear or friction.

Mr. Gasket Harmonic Balancer Bolt for Ford V8 except 351C. Fits 221,260,289,302,351W small block Windsor engines, 332,352,360,390,406,410,427,428 FEs, and 429,460 385 series big blocks. 5/8-18 x 2 inch long heat treated black oxide coated Grade 8 alloy steel with a thick parallel ground washer to provide accurate, uniform torque.

Product Features:

• Heat treated black oxide coated Grade 8 alloy steel
• Thick parallel ground washer provides more accurate, uniform torque
• Hex Prevents Socket Slippage
• Accurate And Uniform Torque
• Black Plated Finish

This kit relocates the oil filter for quick, clean and easy access and increased filtering. It is complete with precision die cast aluminum by-pass, filter brackets and all high pressure connectors.

Product Features:

• Relocate oil filter to an easy access location

This Mr. Gasket Oil Pan comes in chrome plated steel. Complete with drain plug, washer & bolts. Stock depth and capacity. Gasket & chrome-plated dipsticks with tubes sold separately.

Product Features:

• Includes Mounting Bolts
• Includes Drain Plug/Washer/Bolts

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

• Easy to Install
• Superior Material
• Saves Your Tie Rods
• Lasts Longer
• Looks Great

Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:

• Oil Filled For Better Cooling
• Optimized Low Resistance
• Silicon Magnetic Steel E-Core
• Higher Energy/Voltage Outputs
• Quicker Starts
• Improved Idle Quality
• Resists Shock And Vibration
• Resists Corrosion

Product Features:

• MINI SPOOL 8.8 FORD 28SPL

K&N air intake systems are engineered for increased performance, outstanding durability, and sleek aesthetics – and are available in an assortment of finishes and powder coatings. K&N’s state-of-the-art High-Flow Air Filter helps to shield your engine from contaminants, while a meticulously engineered aerodynamic tube design contributes to a guaranteed increase in horsepower and torque. K&N air intake systems are designed to improve acceleration, towing, and throttle response while providing world class protection for your engine. Our intakes are dyno-tested and provide up to 50% more airflow compared to OEM intake systems. K&N intakes are easy to install and maintain with air filter cleaning required only every 100,000 miles.

Product Features:

• GUARANTEED INCREASE IN HORSEPOWER: Dyno-tested with up to 50% more airflow than restrictive factory box air filter and intake tube
• BETTER TOWING: Improves acceleration and uphill performance when towing by improving throttle response.
• IMPROVED ENGINE SOUND: Hear the power under the hood.
• WORLD CLASS PROTECTION: Pushing the limits of engine protection by protecting your engine from harmful contaminants
• EASY MAINTENANCE: No filter cleaning required for up to 100,000 miles
• EASY TO INSTALL: Bolt-on power in less than an hour with basic hand tools. K&N air intake systems are one of the easiest ways to guarantee an increase in horsepower.
• DYNO TESTED: Dyno-tested for a guaranteed increase in horsepower and acceleration with no ECU tune required
• HIGH QUALITY: Made in America.

LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:

• High Performance
• Affordable
• Durable 16 Gauge Material
• Welds Easier
• Lasts Longer
• Heat Cured
• High Heat Resistant

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 180 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

Product Features:

• Most Complete Fuel Injection System Available
• Bolt On Performance
• Ready To Run Out Of The Box
• Easy Connection And Quick Removal Connector

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.

Super Intake Manifold Bolts

The Original Pro Stick shifter delivers rock-solid performance, mixed with clean design cues and compact size. This is why you see so many Pro Stick shifters at the race track. We start off with a heavy duty steel base with a hardened steel gate plate, a reverse lockout feature that only requires one hand to operate, and complies with NHRA/IHRA safety rules. Then add the billet aluminum shift handle with classic white shift knob, lightweight aluminum trigger and finish it off with a brushed aluminum cover with quick release pins, and you end up with one good looking bullet-proof race shifter. Optional Forward and Reverse shift pattern gate plates are available for most popular 2, 3 and 4-speed transmissions. This model Pro Stick comes out of the box ready for action for most popular 3-speed transmissions, includes a 5-foot Super Duty shift cable, brackets, levers, hardware and detailed instructions for an easy installation. Be sure to check out all the optional Magnum Grip side grip plates including the one and two button 12-volt momentary switches or any of the other accessories we offer for the Pro Stick in the Shifter Accessories section. Notes: AOD requires installation kit #40496, AODE & 4R70W requires installation kit #40504, E40D & 4R100 requires installation kit #40505, 2004R & 700R4 require gate plate #80712, 4L60E – 4L85E equipped with PRNDL switch requires cable bracket kit #70499 and gate plate #80712. Overall Dimensions – 8.25L x 2.92W x 9.25H

Product Features:

• All One-Handed
• Reverse Lockout Meets NHRA And IHRA Requirements
• Mount Directly To Floor/Chassis/Or w/Quick Release
• Ultimate For Powerglide Applications
• Lightweight Brushed Alum. Cover
• Cover Removed Quickly and Easily
• Includes 5 Ft. Super Duty Race Cable
• Quick Change Plate Design

Product Features:

• Prevents Air Inclusion
• Direct Replacement
• For OE Bleeders
• One Person Bleeds Safely
• Without The Mess
• No Chance Of Air Bubbles

Product Features:

• Polished Finish
• Raised Fins w/Black Mat Background
• Detailed With Allen Hex Heads
• 2 Piece Look; 1 Piece Construction
• Clears Most Roller Rockers
• Clears Valvetrain Components
• Heavy Gauge

Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.

Product Features:

• Manufactured from cellulose/nitrile composition gasket material
• Provides excellent sealing and durability
• Silicone beading on both sides of each gasket
• Complete with manifold end seals and distributor gasket
• For OE replacement, high performance street, drag race and oval track use
• Creates Tight Leak proof Seal

Product Features:

• Firm in the Center Yet Soft on the Outside
• Allows Flex and Pivot When Needed

The Edelbrock #38183 is a single-bore 90mm throttle body designed with a 5.0L Ford-style base pad. It is fully machined and assembled by Edelbrock. It includes a Throttle Position Sensor, a progressive throttle cable lever, and cruise and kick-down attach

Product Features:

• Solid Bushing Chain Resists Stretching
• For Use with Stock or Edelbrock Camshafts
• Stressproof Steel Crank Gears
• 3 Keyway Setting Points To Ensure Accurate Timing
• True Bearing Surface Rolls with the Sprockets
• For Engine w/ 2-piece Fuel Pump Eccentric or EFI

Product Features:

• Complete Single For Flat Tappet
• 60cc Combustion Chamber Volume
• 170cc Intake/60cc Exhaust Runner Volume
• 2.02 in. Intake/1.60 in. Exhaust Valve Diameter
• 0.625 in. Deck Thickness

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
• Not intended for use in emission controlled vehicles.

The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.

Product Features:

• Helically wound conductor suppresses electro and radio noise
• Kevlar core combination for great strength and durability
• Heavy Duty Terminals For Secure Connection
• 8mm silicone and synthetic jacket resists heat and abrasion
• 500 Ohms/ft. Resistance For Improved Spark Delivery And Power
• Silicone Boots Protect Against High Exhaust Temps