Name: Hei Remote Mount Super Coil
Brand: Accel
SKU: 140024
Price: 65.99 USD
Rating: 5.0 (7 reviews)

from

$65.99

Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, crisper throttle response and more high RPM power. Compatible with late model GM computer controlled remote mount HEI systems. Direct bolt-in, plug-in replacement. Can also work with CD ignition systems. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy transfer and resists corrosion better than aluminum. Comes complete with new mounting hardware. High dielectric strength ACCEL yellow over molded housing. Output is 48,000 volts with 0.2ohms resistance.

Product Features:

Remote Mount Ignition Coil
Higher Energy/Voltage Outputs
Quicker Starts
Improved Throttle Response
More High RPM Power
Increase Energy Transfer
Resist Corrosion
W/New Mounting Hardware

from

$499.99

Power Train

from

$43.99

Fits Chevy small block 265-400 CID, Chevy big block 396-454 CID, & 90 degree Chevy V6. The Starter Motor Heat Shield is built with heat-resistant material sandwiched between two aluminum plates. The shield protects the starter from heat buildup from the exhaust system, especially important when using headers.

Product Features:

Designed to prevent starter overheat due to extreme exhaust temperature
Heat resistant material sandwiched between 2 aluminum plates
Protects Starter From High Temperatures
Made Of 2 Sheets Of Aluminum Heat Resistant Center
Natural Finish

from

$16.99

FRAM Racing® filters are designed with a heavy-gauge tapping plate and an extra-thick* steel can that is able to withstand the high pressure flexing caused by demanding driving conditions. A spiral-shaped center tube provides protection against collapse, and tough steel end caps add even more durability. A screen-over 22psi filter bypass valve provides additional protection against larger contaminants.**

Product Features:

Proven protection for up to 10,000 miles
Engineered for use with synthetic or conventional motor oils
Filter media is a blend of fiber and resin that captures 95% of the dirt particles
The perfect balance of dirt-trapping efficiency and dirt-holding capacity

from

$184.99

Product Features:

Remote Thermostat Housing

from

$74.99

Made from quality materials for durability, DynoMax® pipe is manufactured with precision benders and fixture checked to ensure a precise fit for quick and easy installation.

Product Features:

IMPROVED FLOW CAPACITY — Mandrel bends (where applicable) improve flow capacity over traditional bends while increased pipe diameter from OE sizes increases flow and power
DESIGNED TO PERFORM — Fixture checked to ensure a precise fit for quick and easy installation
AVAILABLE IN DIFFERENT SIZES — Offered in a variety of styles and sizes for a quality vehicle repair
PREMIUM MATERIALS – Made from aluminized steel for durability and long life
BETTER TOGETHER — Use premium DynoMax® accessories when installing DynoMax mufflers and exhaust systems for a complete performance exhaust system upgrade

from

$154.99

Product Features:

Aluminized Steel Construction
3in. Inner Pass Tubes
Reduce Backpressure
Increase Horsepower
No Glass To Burn Or Blow Out
Will Flow In Either Direction
Welded For Strength/Durability

from

$249.99

Product Features:

Fuel Economy From The Engine
Leak Test For Max Performance
Mandrel-Formed Power Plenum
Leakproof O-Ringed Port Seals
Include All Mounting Hardware

from

$109.99

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

Less than 50 ohms per foot for superior spark
Ferro-magnetic impregnated core creates an effective EMI choke
40 ft. Of Conductor Wound Into A Single Foot Of Wire
For high EMI suppression
Conductor core features Dupont Kevlar material
Proprietary compound sleeves for resistance to high heat/abrasion

from

$38.49

Ultra-Seal is Mr. Gasket premium valve cover gasket material. It’s manufactured from a high density cork and rubber blend with a black latex coat applied to the outside to help seal minor flange irregularites and eliminate oil leakage. It creates a positive seal by controlled swelling of the gasket material when exposed to hot oil. For original equipment replacement, high performance street, drag race and oval track use. Sold as a pair, these gaskets are .187 inch thick. They fit both 1987-2002 Gen I Chevrolet Small Blocks as well as 1992-1997 Gen II LT-Based Small Blocks.

Product Features:

Manufactured from high-density cork /rubber blend gasket material
A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage
Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil
For OE replacement, high performance street, drag race and oval track
.187″ thick
Handles Ex Flange Pressure
Forms Leak Proof Seal
Black Latex Coating

from

$443.99

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:

7 in. Diameter
Absolutely the most accurate way to trigger the ignition.
The non-magnetic pickup cannot be false triggered.
Powerful magnets are embedded in a billet aluminum trigger wheel.

from

$222.99

Product Features:

GM 10BL 8.5 R/P 4.10 FRT/REAR MGP

from

$31.99

ACCEL high performance standard size caps offer superior protection from arc-thru and crossfire. Features hi-performance. 60kV- rated alkyd compound, stress-relieved at molding to ensure stability. Brass inserts provide for high spark energy flow.

Product Features:

Brass Inserts Provide For High Spark Energy Flow

from

$39.99

Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.

Product Features:

Allows Sway Bar System to Work At 100% Efficiency
Zerk Type Fittings
Allows for Periodic Greasing
Lasts Much Longer Than OEM Rubber Bushings
Handling Characteristics Improve Dramatically

from

$34.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

from

$80.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets
For OEM Hydraulic Roller Lifter Cams Only

from

$60.29

Copperseal exhaust gaskets are unique gaskets made from .043 inch solid copper. They feature an embossed O-ring design for a leak proof seal. They won’t shrink, deteriorate or blowout. Header bolts stay tight. Ideal for motor homes and towing.

Product Features:

Will Not Shrink/Deteriorate
Creates A Tight Leak Proof Seal
Helps Lower Under hood Temps
Seals Irregular Surfaces
Seals Slightly Damaged Surface
Ideal For Tow Vehicles
Ideal For Motor Homes

from

$78.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$27.49

Secure the harmonic balancer or dampener on your Chevy. Works on original equipment, high performance street, drag or circle track applications. Features a heat treated black oxide coated Grade 8 alloy steel bolt for strength with a tall hex head to prevent wrench from slipping. An extra thick parallel ground washer provides accurate, uniform torque, and a lock washer is also included.

Product Features:

Heat treated black oxide coated Grade 8 alloy steel
Tall hex head bolt to prevent wrench from slipping
Extra thick parallel ground washer provides accurate, uniform torque
Washers Provides More Accurate And Uniform Torque
Grade 8 Alloy Steel

from

$148.99

Constructed of thicker than stock steel plate to withstand the stress of high stall speed converters and high RPM engine. Zinc dichromate plated to resist rust and corrosion. Meets SFI specification 29.1 for racing.

Product Features:

Thicker Than Stock Steel Plate
Ring Gear Securely Welded
Dual Bolt Patterns
Zinc-Dichromate Plated To Resist Corrosion
Withstands High Torque and RPM

from

$336.99

Easy to install one piece 16-gauge powder-coated heat shield requires no cutting or drilling. Stylish powder-coated steel or brushed aluminum cover blocks heat and directs cold air to the filter while quieting intake noise. The precision designed molded plastic intake tube maximizes airflow volume and speed for optimum power gains. 360 degree flow, washable and reusable, limited lifetime filters are high flow and high performance.

Product Features:

Uses Pro 5R Filter For Maximum Air Flow
Rotomolded Plastic Tube For Maximum Air Flow
13% cfm Flow Gain
Increased Horsepower And Torque

from

$149.99

K&N performance High-Flow Air Filters are engineered to improve engine performance. Unlike disposable paper filters which must be frequently replaced, K&N Air Filters are washable, reusable, and engineered to last for the life of your vehicle or outdoor power small engine. Engineered to fit easily into your factory air box, installation can be completed in a matter of minutes! K&N develops and tests each product on the world┐s toughest race tracks, so we can bring the highest level of performance to your daily driving. Join the millions of customers who have saved money and improved vehicle performance by upgrading to K&N filtration.

Product Features:

ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (based on the average miles driven per year of 15,000 miles)
ULTIMATE LONGEVITY: No-hassle lifetime warranty on stock replacement K&N air filters- limitations apply
EASY INSTALLATION: K&N Air Filters are pre-treated and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
ECO-FRIENDLY: Using a washable, reusable engine air filter helps reduce replacement air filter waste- a K&N air filter is designed to last longer than 10 or more disposable filters
MADE IN USA: K&N Air Filters are proudly made in the USA for trusted quality & reliability

from

$204.49

Hypertech Power Chips are engineered for stock 1981-1995 GM vehicles. The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. Street Runner Power Chips are designed for daily street driving or competition in unmodified vehicles using a stock thermostat.

Product Features:

Designed For Daily Street Driving
For Unmodified Vehicles w/Stock Thermostat
Controls Engines Air/Fuel Ratio
Controls Spark Advance For Max Power
Potential Gas Mileage Improvements
No Wiring Or Soldering Required
Installs In Less Than 30 Minutes

from

$349.99

K&N air intake systems are engineered for increased performance, outstanding durability, and sleek aesthetics – and are available in an assortment of finishes and powder coatings. K&N’s state-of-the-art High-Flow Air Filter helps to shield your engine from contaminants, while a meticulously engineered aerodynamic tube design contributes to a guaranteed increase in horsepower and torque. K&N air intake systems are designed to improve acceleration, towing, and throttle response while providing world class protection for your engine. Our intakes are dyno-tested and provide up to 50% more airflow compared to OEM intake systems. K&N intakes are easy to install and maintain with air filter cleaning required only every 100,000 miles.

Product Features:

GUARANTEED INCREASE IN HORSEPOWER: Dyno-tested with up to 50% more airflow than restrictive factory box air filter and intake tube
BETTER TOWING: Improves acceleration and uphill performance when towing by improving throttle response.
IMPROVED ENGINE SOUND: Hear the power under the hood.
WORLD CLASS PROTECTION: Pushing the limits of engine protection by protecting your engine from harmful contaminants
EASY MAINTENANCE: No filter cleaning required for up to 100,000 miles
EASY TO INSTALL: Bolt-on power in less than an hour with basic hand tools. K&N air intake systems are one of the easiest ways to guarantee an increase in horsepower.
DYNO TESTED: Dyno-tested for a guaranteed increase in horsepower and acceleration with no ECU tune required
HIGH QUALITY: Made in America.

from

$30.99

Wiring Harness and CapacitorPremium quality wire harness and capacitor insure good connection and “static free” operation.

Product Features:

PerTronix D9007 Flame-Thrower HEI Distributor 4-Pin Wire Harness/Capacitor
Premium quality wire harness and capacitor.

from

$65.99

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$203.99

Edelbrock part #9646 Pushrods are designed for small-block Chevy V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise forme

Product Features:

7.25 in. Length
0.312 in. Diameter
4130 Chromoly Steel Material
Black Oxide Finish
Made In The USA

from

$399.99

The street Pro-Billet is a popular route for people looking for proven race performance for their street cars. A vacuum advance canister provides economy and the proven MSD mechanical advance gives you the opportunity to dial-in a timing curve to fit your needs. Inside, an oversized steel shaft is QPQ coated for low friction and rides in a sealed ball bearing at the top of the distributor with an extra-long sintered bushing at the bottom. This combination keeps the shaft steady creating accurate spark delivery at any RPM. The street Pro-Billet relies on a magnetic pick-up to trigger the MSD Ignition control which delivers the powerful sparks to the coil. This pick-up is extremely accurate and never needs adjusting.

Product Features: