Name: ThermoMaster Power Chip
Brand: Hypertech
SKU: 121262
Price: 168.89 USD

from

$168.89

Hypertech ThermoMaster Power Chips are engineered for stock 1995-1981 GM vehicles (premium octane fuel required). The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. ThermoMaster Power Chips are designed for daily street driving or competition in unmodified vehicles using a 160 Deg. or 180 Deg. thermostat. Hypertech Power Chips(TM) are emissions certified 50-state legal (application specific).

Product Features:

Use w/Low-Temp 160-180 Deg. PowerStat Thermostat
Controls Engines Air/Fuel Ratio
Controls Spark Advance For Max Power
Potential Gas Mileage Improvements
No Wiring Or Soldering Required
Installs In Less Than 30 Minutes
Product might not be available in all states due to local laws.

from

$26.99

Mechanical Advance Curve Ki tPrecision machined chromoly weights and center plate eliminate erratic timing. Three sets of springs, guide bushings and complete installation instructions make recurving your distributor easy.

Product Features:

PerTronix D9001 Flame-Thrower HEI Distributor Advance Curve Kit
Precision machined chromoly weights and center plate.

from

$83.99

A true performance application component for cars, trucks, hot rods, racing/competition, yet popularly used for street vehicles when more horsepower is added. Soft running enough to absorb vibrations for street use yet rugged for racing use. Helps control torque on high performance vehicles. Maintains proper drive shaft angle to help prevent early wear and unexpected power train damage. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal transmission mounts. Resistant to under vehicle fluid oils, coolants and road contaminants. Made of Energy’s Hyper-Flex performance polyurethane and heavy duty hardware – for added durability.

Product Features:

Unique Safety Interlock Design
Impervious to Vehicle Oils and Chemicals
Strong Enough Too Handle High Performance

from

$184.99

Product Features:

Remote Thermostat Housing

from

$90.99

The B&M Shift Plus, recalibrates your transmission’s hydraulic system electronically which firms up the shifts and reduces heat and slippage. A simple flip of the switch allows you to choose which shift firmness setting you want to run.

Product Features:

Installs In Minutes
Reduces Slippage and Heat
50 State Emissions Legal
Recalibrates Hydraulic System
Recalibrates Electronically
Fun and Pleasurable Drive
Extends Transmission Life
Simple Flip Of Switch

from

$32.09

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

Features 12-point Smaller-than-standard Bolt Head
Thick Flat Washers Distribute Optimum Clamp Load
Ideal Use Where Space Is Minimal On Race Manifolds
Bolts And Washers Zinc Plated For Protection
Zinc Plated For Protection

from

$87.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$222.99

Product Features:

GM 10BL 8.5 R/P 4.10 FRT/REAR MGP

from

$89.99

ACCEL Heavy-Duty Caps offer superior protection from arc-thru and crossfire. Features hi-performance 60,000 volt alkyd compound, stress-relieved at molding to ensure stability.

Product Features:

Fits Most Stock And Modified Distributors
Brass inserts provide for high spark energy flow
Polyester Glass Filled For Durability
Heavy duty for maximum energy transfer

from

$368.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$399.99

The street Pro-Billet is a popular route for people looking for proven race performance for their street cars. A vacuum advance canister provides economy and the proven MSD mechanical advance gives you the opportunity to dial-in a timing curve to fit your needs. Inside, an oversized steel shaft is QPQ coated for low friction and rides in a sealed ball bearing at the top of the distributor with an extra-long sintered bushing at the bottom. This combination keeps the shaft steady creating accurate spark delivery at any RPM. The street Pro-Billet relies on a magnetic pick-up to trigger the MSD Ignition control which delivers the powerful sparks to the coil. This pick-up is extremely accurate and never needs adjusting.

Product Features:

Designed for street/performance use w/mechanical or vacuum adv.
Must Be Used w/An MSD Ignition Control
Supplied w/An HEI Style Distributor Cap And Rotor
Accepts Cap-A-Dapts
O-ring seals can be installed for oil press. control (Mods only)
Special oil tract improves lubrication to the dist./cam gear
Nylon pads ensure smooth operation of the advance weights
Advance weight pins are staked and tig welded to the plate

from

$10.49

This chrome plated breather, embossed with a Mr. Gasket logo, is perfect for race car vacuum balance systems and OEM use. It fits any 1 1/4 inch diameter hole. It has metal baffle/foam element with 1 inch outer diameter neck and 5/8 inch outer diameter breather tube.

Product Features:

Internally battled
High-porosity filter
Ideal for high performance
Includes rubber grommet

from

$999.99

Product Features:

Designed For Today’s Larger Cubic Inch Big Block
Perfect For Hard Core Drag Racers
Permanent Mold Casting Process
For Lighter And More Consistent Castings
Dyno Proven To Make 17hp More Than Competitors

from

$204.49

Hypertech Power Chips are engineered for stock 1981-1995 GM vehicles. The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. Street Runner Power Chips are designed for daily street driving or competition in unmodified vehicles using a stock thermostat.

Product Features:

Designed For Daily Street Driving
For Unmodified Vehicles w/Stock Thermostat
Controls Engines Air/Fuel Ratio
Controls Spark Advance For Max Power
Potential Gas Mileage Improvements
No Wiring Or Soldering Required
Installs In Less Than 30 Minutes
Product might not be available in all states due to local laws.

from

$349.99

K&N air intake systems are engineered for increased performance, outstanding durability, and sleek aesthetics – and are available in an assortment of finishes and powder coatings. K&N’s state-of-the-art High-Flow Air Filter helps to shield your engine from contaminants, while a meticulously engineered aerodynamic tube design contributes to a guaranteed increase in horsepower and torque. K&N air intake systems are designed to improve acceleration, towing, and throttle response while providing world class protection for your engine. Our intakes are dyno-tested and provide up to 50% more airflow compared to OEM intake systems. K&N intakes are easy to install and maintain with air filter cleaning required only every 100,000 miles.

Product Features:

GUARANTEED INCREASE IN HORSEPOWER: Dyno-tested with up to 50% more airflow than restrictive factory box air filter and intake tube
BETTER TOWING: Improves acceleration and uphill performance when towing by improving throttle response.
IMPROVED ENGINE SOUND: Hear the power under the hood.
WORLD CLASS PROTECTION: Pushing the limits of engine protection by protecting your engine from harmful contaminants
EASY MAINTENANCE: No filter cleaning required for up to 100,000 miles
EASY TO INSTALL: Bolt-on power in less than an hour with basic hand tools. K&N air intake systems are one of the easiest ways to guarantee an increase in horsepower.
DYNO TESTED: Dyno-tested for a guaranteed increase in horsepower and acceleration with no ECU tune required
HIGH QUALITY: Made in America.

from

$43.99

Fits Chevy small block 265-400 CID, Chevy big block 396-454 CID, & 90 degree Chevy V6. The Starter Motor Heat Shield is built with heat-resistant material sandwiched between two aluminum plates. The shield protects the starter from heat buildup from the exhaust system, especially important when using headers.

Product Features:

Designed to prevent starter overheat due to extreme exhaust temperature
Heat resistant material sandwiched between 2 aluminum plates
Protects Starter From High Temperatures
Made Of 2 Sheets Of Aluminum Heat Resistant Center
Natural Finish

from

$30.99

This Spectre Alternator Bracket is an upper mount designed to fit 1969 and later Chevrolet Big Block engines with a long water pump. Featuring a triple chrome-plated finish and high quality steel construction, this part is an OEM replacement that mounts on the passenger’s side.

Product Features:

Fits Big Block Chevy engines with a long water pump from 1969 and later
Manufactured from high quality steel
Upper bracket for passenger side mounting
Features a triple chrome-plated finish
Stock replacement part

from

$60.29

The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.

Product Features:

Helically wound conductor suppresses electro and radio noise
Kevlar core combination for great strength and durability
Heavy Duty Terminals For Secure Connection
8mm silicone and synthetic jacket resists heat and abrasion
500 Ohms/ft. Resistance For Improved Spark Delivery And Power
Silicone Boots Protect Against High Exhaust Temps

from

$68.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
Raises combustion sealing force to roughly three times that of standard head gaskets.
Steel wire rings for the greatest combustion seal strength.
Not intended for use in emission controlled vehicles.

from

$74.99

Made from quality materials for durability, DynoMax® pipe is manufactured with precision benders and fixture checked to ensure a precise fit for quick and easy installation.

Product Features:

IMPROVED FLOW CAPACITY — Mandrel bends (where applicable) improve flow capacity over traditional bends while increased pipe diameter from OE sizes increases flow and power
DESIGNED TO PERFORM — Fixture checked to ensure a precise fit for quick and easy installation
AVAILABLE IN DIFFERENT SIZES — Offered in a variety of styles and sizes for a quality vehicle repair
PREMIUM MATERIALS – Made from aluminized steel for durability and long life
BETTER TOGETHER — Use premium DynoMax® accessories when installing DynoMax mufflers and exhaust systems for a complete performance exhaust system upgrade

from

$449.99

The Hurst truck Pro-Matic 2 ratchet action shifter is ideal for street or strip performance. It features a lighted gear indicator, NHRA approved reverse lockout, chrome stick and a black knob.

Product Features:

Extended Shifter Stick
Forward and Reverse Ratchet Action
Cable Operated
Illuminated Gear Indicator
Neutral Safety and Back Up Light Switch

from

$27.49

Secure the harmonic balancer or dampener on your Chevy. Works on original equipment, high performance street, drag or circle track applications. Features a heat treated black oxide coated Grade 8 alloy steel bolt for strength with a tall hex head to prevent wrench from slipping. An extra thick parallel ground washer provides accurate, uniform torque, and a lock washer is also included.

Product Features:

Heat treated black oxide coated Grade 8 alloy steel
Tall hex head bolt to prevent wrench from slipping
Extra thick parallel ground washer provides accurate, uniform torque
Washers Provides More Accurate And Uniform Torque
Grade 8 Alloy Steel

from

$87.19

Designed to keep the rocker arms positively locked for precise and critical valve train adjustments. Manufactured from quality grade steel, then heat-treated for extra strength and plated with a durable finish. Kits include 16 rocker arm nuts with socket head set screws and one hex key wrench.

Product Features:

(16) Rocker Arm Nuts w/ Locks 3/8″-24 Threads
Shank O.D. .540″
Includes Locks and Hex Wrench
High-Quality Grade Steel
Heat-Treated For Ex Strength
Plated With Durable Gold Tone Finish

from

$461.99

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:

6.25 in. Diameter
Absolutely the most accurate way to trigger the ignition.
The non-magnetic pickup cannot be false triggered.
Powerful magnets are embedded in a billet aluminum trigger wheel.

from

$91.99

Adds a dramatic amount of performance and durability to any vehicle, cars, trucks and SUVs. Helps the vehicle be in control – when maneuvering through turns, during standing start accelerations, braking, even over bumps and berms. Made of Energy’s Hyper-Flex performance polyurethane which lasts 5 -10 times longer than conventional rubber components.

Product Features:

Made of Superior Hyper-Flex+ Material
Adds Dramatic Amount of Performance/Durability
Helps Vehicle Be in Control
Allows the Suspension to Function Properly

from

$89.99

K&N performance High-Flow Air Filters are engineered to improve engine performance. Unlike disposable paper filters which must be frequently replaced, K&N Air Filters are washable, reusable, and engineered to last for the life of your vehicle or outdoor power small engine. Engineered to fit easily into your factory air box, installation can be completed in a matter of minutes! K&N develops and tests each product on the world┐s toughest race tracks, so we can bring the highest level of performance to your daily driving. Join the millions of customers who have saved money and improved vehicle performance by upgrading to K&N filtration.

Product Features:

ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (based on the average miles driven per year of 15,000 miles)
ULTIMATE LONGEVITY: No-hassle lifetime warranty on stock replacement K&N air filters- limitations apply
EASY INSTALLATION: K&N Air Filters are pre-treated and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
ECO-FRIENDLY: Using a washable, reusable engine air filter helps reduce replacement air filter waste- a K&N air filter is designed to last longer than 10 or more disposable filters
MADE IN USA: K&N Air Filters are proudly made in the USA for trusted quality & reliability

from

$25.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Die cut silicone rubber gaskets conform to out-of-flat covers
Great for on-again/off-again situations
Not intended for use in emission controlled vehicles.

from

$198.99

The Super 50 series muffler is a larger version of Flowmaster’s 50 series Delta Flow muffler. Originally designed for trucks and SUV’s, it is also well suited to muscle car and high performance applications. In addition, the larger case size significantly reduces interior resonance and provides a deep, rich tone along with mileage and power gains. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.