from

$283.99

This differential disc kit is a low-cost, time-saving repair solution for the posi-traction function. They are designed to match the fit and performance of the original disc on specific vehicle years, makes and models.

Product Features:

Direct replacement – this differential clutch kit provides the necessary components for repairing the original equipment on specific vehicles
Quality materials – all components are built for reliable longevity and performance
Smart solution – provides original equipment fit and function for a competitive price compared to original manufacturer
Trustworthy quality – backed by team of designers and engineers in the United States

from

$22.79

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHECKER 55-82; CHEV 60-12; DODGE 57-02; FORD 55-10; GMC 63-07; INTL 57-02; ISUZU 96-01; KW 81-18; MACK 80-90; MAZDA 87-94; MITS 87-09; OLDS 90-01; PLYM 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 3 Lbs
BEARING ID / BORE: 1.3780 INCH / 35 MM
CENTERLINE: 2.28 INCH / 58 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
STYLE: ROUND FRAME
COMPLETE MOUNT

from

$8.99

Product Features:

Axle o-ring
Fits Ford 10.25″ and 10.5″

from

$5.99

Product Features:

Floater roll pin
Fits Dana Spicer 44 and Chrysler 8.75″
Powr Lok positraction only

from

$5.99

Product Features:

Outer oil slinger for Dana Spicer 60, 70, 70U and 70HD

from

$251.99

Yukon replacement trail repair kit for Dana 60 with 1310 size U/joint and u-bolts. This kit comes with a yoke, U/joint, pinion seal, U/bolt or strap kit, pinion nut, and pinion nut washer (if applicable).

Product Features:

Fits Dana Spicer 60 and 70
1310 u-joint size
Kit includes yoke, U-joint, pinion seal, pinion nut and washer, U-bolts and threadlocker

from

$73.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$274.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. Axle bearing and seal kit for 10.25″ Ford (full-floating). This kit includes Timken inner and outer bearings and races along with high quality seals. Unit is sold per side and is covered for one year against manufacturing defects. This axle bearing & seal kit services one side only.

Product Features:

Fits Ford 10.25″
Includes inner and outer bearings and races and axle seal
Services one side

from

$139.99

Dana 44 & 9.25 Chrysler TracLoc clutch kit.

Product Features:

Clutch kit
Fits Dana Spicer 44 and Chrysler 9.25″ Trac Loc positraction

from

$679.99

These heavy-duty lockouts feature all steel construction, including Chrome-Moly internals, for the ultimate in durability & strength. The hubs will not disengage under high torque applications and defaults to the locked position under use. Engagement comes from just a 1/3 turn of the all-steel, low-profile bezel. The Yukon Hardcore locking hubs are not only great looking, but features a low-profile design to minimize impact with obstacles, and a proprietary coating on the locking gears for decreased friction & long life. Yukon Hardcore Locking Hubs come with a Limited Lifetime warranty against manufacturer’s defect. This locking hub set will not fit housings with Bill of Materials numbers 610033-2, 3, 5 or 6.

Product Features:

Fits 1979-1991 GM, 1978-1997 F350 and 1979-1993 Dodge one ton fronts with Dana Spicer 60
30 spline
All steel construction
Chromoly internals for added strength
Low profile bezel to reduce impact with obstacles
Defaults to locked position
1/3 turn from disengaged to engaged

from

$11.99

Replacement ring gear bolt for Model 35, Dana 25, 27, 30 & 44. 3/8″ x 24.

Product Features:

Ring gear bolt for Dana Spicer 25, 27, 30, 44 and AMC Model 35
3/8″ x 24 thread

from

$26.99

Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.

Product Features:

Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
Left hand thread

from

$9.99

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$11.49

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$669.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

Fits Dana Spicer 44 with 30 spline axles
Made from 9310 steel for added strength
Replaces the spiders in a standard carrier case

from

$319.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 60 front
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$6.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$251.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$26.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$20.29

This drive shaft bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this engine mount bolt matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this drive shaft bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$11.99

55P Chevy Passenger Drop Out gasket.

Product Features:

Side gear thrust washer
Fits Ford 10.25″

from

$44.99

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

Includes three quarts of conventional oil

from

$374.99

Replacement front spindle for Dana 60 Ford, 5 holes, 7″ long, 6.5″ flange, 2.020×2.255bearing.

Product Features:

Fits 1978-1979 Ford F250 and 1985-1998 Ford F350 with Dana Spicer front
7.00″ tall
6.5″ flange
5 bolt holes
2.255″ and 2.020″ bearing journals

from

$3.29

Product Features:

Brand may vary by location

from

$88.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$9.49

This axle vent is designed to match the fit and function of the original vent on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this axle vent is designed to match the fit and function of the original vent on specified vehicles
Restores functionality – reliable replacement for an original vent that has failed due to blockage or fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$34.99

1310 U-bolts, 5/16″ x 1-3/8″ Dana 30, Dana 44, 8.2″, 12P, 12T, VET, Model 20.

Product Features:

u-joint u-bolt kit
Fits AMC Model 20, Dana Spicer 30 and 44, GM 8.2″, 12 bolt passenger car and truck and 1963-1979 Corvette
1310 u-joint size
Includes two u-bolts and four nuts

from

$31.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific, providing unsurpassed quality for a seal you can trust
Validated for fit, form, and function
Engineered for the sealing repair environment
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes