1990 Chevrolet V3500 Drivetrains

Below you will find various in-demand Chevrolet Drivetrains, components and accessories for your 1990 V3500. Advance Auto Parts has popular V3500 parts like Differentials, 4WD Components, Universal Joints and more. You’ll also find aftermarket and OEM Drivetrains for other V3500 model years including 1989 1991 and more. Select a category of 1990 Chevrolet V3500 Drivetrains below and start saving instantly.

Please Select your Vehicle to See Exact Fit Parts

Popular 1990 Chevrolet V3500 Drivetrains Categories

Differential Oil

Axle Shaft Universal Joints

4WD Actuator Switches

U-Joints

Drive Shaft and Axles

4WD Hubs

Miscellaneous CV and U-Joint Parts

Drive Shaft Center Supports

Differential Open Unit and Components

Differential Covers

Center Support Bearings

U-Joint Strap Kits

Drive and Prop Shaft Assemblies

Differential Bearings

Differential Axle Shafts

U-Joint CV Repair Kit

Spindle Hub Seals

Axle Shaft Seals

Drive Shaft Slip Yoke Sleeves

Differential Pinion Pilot Bearings

Axle Spindle Seals

Axle Shaft Bearings

Transfer Case Output Shaft Seals

Differential Carriers

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Axle Spindle Bearings

Axle Flange Gaskets

Differential Clutch Packs

Differential Ring and Pinions

U-Joint U-Bolt Kits

Differential Cases

Differential End Yokes

Spindle Lock Nuts

Differential Lock Assemblies

Rear Differential Pinion Bearings

Differential Spools

Differential Carrier Bearings

Front Differential Cover Gaskets

Rear Housing Cover Gaskets

Transfer Case Output Shaft Bearings

Transfer Case Differential Bearings

Drive Shaft Seals

Axle Shaft Lock C-Clips

Bearing and Seal Overhaul Kits

Differential Ring Gear Bolts

Axle U-Bolt Kits

Input Shaft Seals

Spindle Retainers

Differential Crush Sleeves

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Gear Install Kits

Mounting Adapter Seals

Oil Pump Housing Seals

Limited Slip Differential Assemblies

Differential Spider and Pinion Gear Kits

Essential Drivetrains for 1990 Chevrolet V3500s

from

$13.99

This transfer case adapter seal matches the fit and function of worn or damaged original equipment part. This seal should be replaced as part any service that requires the transfer case and transmission to be separated.

Product Features:

Ideal replacement – this transfer case adapter O-ring is a direct replacement for a worn or damaged original equipment seal between the transfer case and transmission
Convenient on-hand part – this seal should be replaced whenever the transfer case is removed for service
Application-specific design – this O-ring has been designed of durable materials specifically for this vehicle application
Quality tested – this part has undergone try-on and material testing to ensure a quality fit and long service life

from

$889.99

Differential

from

$487.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

Product Features:

Powertrax® proves that you don’t have to choose between the superior traction of a locking differential and smooth handling and drivability of an open differential. Powertrax Lock-Right Lockers, No-Slip Traction Systems and GRIP limited slip differentials and lockers give you the best of both worlds!
The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.
Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.
Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.
Powertrax® = Extreme Traction Systems!

from

$211.99

Product Features:

GM10.5″ 14 BOLT OPEN EMPTY CASE 4:10 & DWN

from

$11.29

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$40.99

The components in this leaf spring axle U-bolt kit are designed to securely hold the leaf spring or leaf spring bundle to the underside of an axle of a vehicle or trailer. Check the leaf spring dimensions and other relevant application details to select the right type and size U-bolt kit for your needs.

Product Features:

Reliable hardware – the components in this leaf spring axle U-bolt kit are designed to securely hold the leaf spring or leaf spring bundle to the underside of a vehicle or trailer axle
Check fit – carefully review the dimensions of the leaf springs that will be used and other relevant application details to select the right type and size U-bolt kit for your needs
Durable construction – the components in this kit are engineered from quality materials for reliable performance and long service life
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$24.99

Manufactured with premium-grade steel, National cylindrical bearings are designed and engineered to meet OE specifications.

Product Features:

STRONG AND DURABLE: Controlled heat treatment process for strength and durability
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for durability and performance
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
Professional technicians know they can depend on National

from

$14.29

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$46.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$44.99

Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.

Product Features:

BUILT TO LAST – Advanced heat treatment process for strength
PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$232.99

Full-floating, 35 spline diameter, non-drilled blank axle shaft for Dana 60. 40″ inches long. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H axles come with a one year warranty against manufacturing defects.

from

$596.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

from

$25.49

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$869.99

Differential

from

$17.99

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$94.99

Product Features:

BW1356 BEARING & SEAL KIT ALSO 1370 (W/O THE CENTER PLATE)

from

$46.99

This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.

Product Features:

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$9.99

With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.

Product Features:

Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.

from

$43.99

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$15.99

Design type: spring loaded; multi-lip
Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$181.99

Product Features:

FULL SPOOL DANA 60 35 SPLINE 4.56 & UP

from

$28.49

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$112.99

Product Features:

CARRIER BEARING KIT FORD 10.5″

from

$323.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

Meets or exceeds OE specifications

from

$18.99

Product Features:

CARRIER SHIM-DANA 60 & 70

from

$279.99

Worn or damaged differential end yoke causing driveline vibrations- This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$23.99

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

For U-Joints 353, 354, 361, 369 & 497
Fits 1-1/16″ bearings

from

$17.99

Product Features:

NUT PINION – 14 BOLT

Upgrade your 1990 Chevrolet V3500 with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 1990 Chevrolet V3500, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Chevrolet or enhancing its overall performance, Drivetrains are key to keeping your V3500 functioning at its best. At Advance Auto Parts, we offer a wide selection of 198 Drivetrains for the 1990 Chevrolet V3500, designed to meet your needs without breaking the bank. From Differential replacements to 4WD Components upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 1990 Chevrolet V3500 at great prices. Our Drivetrains inventory for this model ranges from just $1.89 to $1,008.00, with an average price of $143.59. Our 198 Drivetrains in stock come from 21 trusted brands, so you’re sure to find the right part for your 1990 Chevrolet V3500 without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1990 Chevrolet V3500, we stock popular OEM and aftermarket Drivetrains from top names like Spicer, Moog, National, and more. Spicer Drivetrains start at just $31.99 and boast an impressive 4.6 stars average rating from customers. Moog and National also bring quality to the table, with Drivetrains available starting at $12.99, and at an average 4.5 stars rating. With 4,518 customer reviews and counting, our 1990 Chevrolet V3500 Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1990 Chevrolet V3500 is always ready to roll. We’re committed to providing you with everything you need to keep your V3500 in top shape, all in one place. Start shopping confidently below for your 1990 Chevrolet V3500!

Best-Selling Differentials for 1990 Chevrolet V3500s

Enhance the driving experience in your Chevrolet with 99 quality Differential components, starting at $1.89.

show more show less

from

$35.99

Valvoline MaxLife Multi-Vehicle ATF is a full-synthetic formulation with advanced additives to prevent the major causes of transmission breakdown and help extend transmission life. Developed to help prevent leaks, maximize transmission performance, reduce transmission wear, and maintain smooth shifting longer than conventional fluids. It is suitable for use in a broad range of ATF applications including most Ford, GM, Toyota, Honda, Nissan, Hyundai, BMW, Mercedes, Volvo, VW & Audi. Recommended for use in the following applications: GM DEXRON-II, DEXRON-III, DEXRON-VI, Ford MERCON LV, Toyota/Lexus Type T, T-II, T-IV, WS, Honda/Acura, ATF-Z1, Nissan/Infiniti Matic-D, Matic-J, Matric-K, Matic-S, Hyundai/Kia SP-II, SP-III, SP-IV, SPH-IV, BMW 7045E, ETL 8072B, LA2634, LT71141, Allison C-4, Mercedes Benz NAG-1, Volvo 1161521, 1161540, 97340, 1273.41, and VW/Audi G-052-025-A2, G-052-162-A1. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.

Product Features:

Formulated with full-synthetic base oils and long life friction modifiers to help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks in high mileage transmissions
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$12.99

Valvoline High Performance Gear Oil is an extreme pressure gear lubricant formulated with quality base oils and superior additives that helps protect against severe temperatures, shock loads, scuffing, scouring, corrosion and pitting in high speed, high load, high torque and high horsepower conditions.

Product Features:

Formulated for reliable gear protection
Protects against severe temperatures to help extend service life
Formulated with extreme-pressure additives to minimize gear wear from shock loads
Helps protect against gear wear from scuffing, scouring, corrosion and pitting
Recommended for conventional hypoid differentials and non-synchronized manual transmissions in passenger cars, light trucks, sport utility vehicles, vans and heavy-duty trucks where an API-GL5 or GL-4 fluid is specified
PLEASE NOTE: Valvoline recommends SynPower Full Synthetic Gear Oil for limited slip differentials

from

$13.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$17.99

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$43.99

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$8.29

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Validated for fit, form and function
Unsurpassed quality you can trust

from

$46.99

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$9.49

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Validated for fit, form and function
Unsurpassed quality you can trust

from

$57.99

3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.

Product Features:

Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive

from

$44.99

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

Includes three quarts of conventional oil

from

$5.99

This differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles
Required replacement – when servicing the differential
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$17.49

Design type: spring loaded; multi-lip
Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$117.99

Product Features:

PINION YOKE
CAST:1310
U-BOLT STYLE

from

$37.99

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$11.29

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

from

$19.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$16.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

from

$6.99

Product Features:

DANA PRELOAD SHIMS (D60 & D70)

from

$43.99

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$99.99

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

Includes three quarts of Redline Shockproof oil

from

$43.99

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$28.49

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$26.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Most Popular 1990 Chevrolet V3500 4WD Components

Customize your Chevrolet with 3 4WD Components products like 4WD Actuator Switches and 4WD Hubs, all priced under $323.99.

show more show less

from

$323.99

Product Features:

Ideal For OEM Hub Replacement
4140 Steel Clutch Ring
Inner Drive Gear
Precision Cast Hub Body

from

$93.99

Carquest Premium Vehicle Solutions provides high-quality solutions for a wide range of applications. The 4WD Actuator ensures seamless transition between 2WD and 4WD modes, providing enhanced traction and stability on challenging terrains without manual intervention. Engineered for maximum performance and durability, our products are built to excel in even the most demanding conditions, ensuring reliable operation and long-lasting value.

Product Features:

Durable Construction: Designed with high-quality materials to withstand harsh environmental conditions, ensuring long-lasting performance in extreme temperatures, vibrations, and moisture exposure.
Precision Engineering: Accurate sensing and switching capabilities provide reliable performance, reducing the risk of malfunctions and improving vehicle safety and efficiency.
Easy Installation & Maintenance: Designed for quick installation and minimal upkeep, reducing downtime and repair costs for both manufacturers and consumers.
Fit/Form/Function: Each vehicle electronic component is engineered to meet or surpass OEM standards, ensuring precise fit, optimal functionality, and reliable performance.

from

$92.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

Meets or exceeds OE specifications

Top Picks for 1990 Chevrolet V3500 Universal Joints

Upgrade Chevrolet V3500s with top-quality Universal Joints parts, including 32 OEM and aftermarket selections for your 1990 model.

show more show less

from

$67.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE – Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN – Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR – Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE – Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$31.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.

Product Features:

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$29.99

For U-Joints 330, 330A, 331 & 331A
Contains two 1.66″ bolt center clamps and four 5/16-24 x 1-5/16″ cap screws

from

$23.99

For U-Joints 353, 354, 361, 369 & 497
Fits 1-1/16″ bearings

from

$33.49

Designed for ease of installation
Includes necessary hardware
Designed for superior performance
Designed for ultimate strength
Increased tolerance for a performance fit
Meets deflection parameters

from

$15.99

Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$42.99

Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASEABLE DESIGN – Greaseable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$35.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE – Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN – Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR – Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE – Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging to provide higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting allows for easy maintenance and the flexible use of the entire assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals are applied to optimize grease retention and reduce contamination

from

$25.99

For U-Joints 355, 372 & 534G
Contains two 1.81″ bolt center clamps and four 5/16-24 x 1-5/16″ cap screws

from

$29.49

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$33.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$41.49

Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASEABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$33.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$48.99

You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.

from

$37.99

Backed by superior materials and rigorous testing, MOOG Super Strength® universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASEABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$34.49

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASEABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$31.49

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$41.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE – Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN – Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR – Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE – Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$36.99

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$16.99

This universal joint strap kit is designed to match the original components required to repair and resecure universal joints on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this universal joint strap kit is designed to match the original components required to repair and resecure universal joints on specified vehicles
Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

In-Demand Drive Shafts and Axles for 1990 Chevrolet V3500s

Select from 28 premium Drive Shafts and Axles parts for your 1990 Chevrolet V3500, with prices ranging from $5.79 to $761.99.

show more show less

from

$38.99

from

$40.99

Anchor 6038 Center support bearings support a driveshaft between transmission and differential. This mount relieves stress on driveline components. Each part is engineered and designed to OE Standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 4 Lbs
BEARING ID / BORE: 1.5750 In. / 40 mm
CENTERLINE: 2.48 In. / 63 mm
Mount Width: 6.62 In. / 168 mm
Style: Round Frame
Not Pictured: Two Dust Shields

from

$45.99

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$5.79

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$24.99

Manufactured with premium-grade steel, National cylindrical bearings are designed and engineered to meet OE specifications.

Product Features:

STRONG AND DURABLE: Controlled heat treatment process for strength and durability
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for durability and performance
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
Professional technicians know they can depend on National

from

$6.99

This drive axle shaft lock C-clip is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this drive axle shaft lock C-clip matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this clip is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$44.99

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$86.99

from

$45.99

from

$44.99

Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.

Product Features:

BUILT TO LAST – Advanced heat treatment process for strength
PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$155.99

Carquest Premium constant velocity (C.V.) axle shaft assemblies are 100% new units that are designed to meet or exceed OE specifications. Every part number is tested to guarantee a proper fit and reliable performance. Carquest Premium CV axles are assembled with a specially formulated high-temperature moly grease to resist friction and wear of the bearings and joints. Our strict engineering and quality specifications ensure a long-lasting repair that is guaranteed with an industry-leading warranty.

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
100% new axle and components
New axle nut or attaching hardware included when applicable
Bearings, races and housings are heat-treated for longer life
Precision-engineered seal mating surfaces for leak-free performance
High moly CV joint grease with stainless-steel boot bands

from

$21.99

Anchor 6056 Center support bearings support a driveshaft between transmission and differential. This mount relieves stress on driveline components. Each part is engineered and designed to OE Standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 3 Lbs
BEARING ID / BORE: 1.3780 In. / 35 mm
CENTERLINE: 2.28 In. / 58 mm
Mount Width: 6.62 In. / 168 mm
Style: Round Frame
Complete Mount

from

$19.99

Value-priced bearing meets all cataloged application requirements.

from

$50.99

Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.

Product Features:

BUILT TO LAST – Advanced heat treatment process for strength
PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$162.99

Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.

Product Features:

BUILT TO LAST – Advanced heat treatment process for strength
PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$16.99

from

$25.49

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$279.99

Direct replacement – this differential end yoke matches the fit and construction of the original yoke
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$761.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$175.99

Schaeffler hanger bearings are engineered and built to provide precise driveshaft alignment, support shafts and axles with the least possible friction and wear under the harshest conditions. This vital component also increases driveline integrity by absorbing and isolating vibration to protect the driveline and provide a smooth, comfortable ride.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$147.99

Drive Axle Shaft Universal Joint

from

$101.99

from

$98.99

Reliable hardware – the components in this leaf spring axle U-bolt kit are designed to securely hold the leaf spring or leaf spring bundle to the underside of a vehicle or trailer axle
Check fit – carefully review the dimensions of the leaf springs that will be used and other relevant application details to select the right type and size U-bolt kit for your needs
Durable construction – the components in this kit are engineered from quality materials for reliable performance and long service life
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$44.49

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

Most Sold 1990 Chevrolet V3500 Transfer Cases

Explore our best-selling Chevrolet parts for the 1990 V3500 among 20 OEM and aftermarket options starting from $7.99.

show more show less

from

$12.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$12.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$7.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$15.99

Design type: spring loaded; multi-lip
Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$8.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$11.49

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$43.49

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$20.49

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$17.49

Product Features:

Brand may vary by location

from

$18.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$43.99

Product Features:

BUILT TO LAST: Advanced heat treatment process for strength
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$94.99

Product Features:

BW1356 BEARING & SEAL KIT ALSO 1370 (W/O THE CENTER PLATE)

from

$94.99

Product Features:

BUILT TO LAST: Advanced heat treatment process for strength
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$319.99

TCaseBrg-SealKit

from

$248.99

TCaseBrg-SealKit

from

$242.99

TCaseBrg-SealKit

from

$52.99

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$11.29

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$10.99

Design type: spring loaded; single-lip
Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$9.59

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

Top-Rated Drivetrains Brands For Your 1990 Chevrolet V3500

Shop for the best-rated brands offering Drivetrains and other products for your 1990 Chevrolet V3500s. Below you’ll find some of our best rated Drivetrains from Spicer, Moog, and National, and more. Drivetrains from these brands that fit a 1990 V3500 start at just $12.99 and are rated as high as 4.6 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular Spicer 1990 Chevrolet V3500 Drivetrains

When it comes to maintaining or upgrading your 1990 Chevrolet V3500, using quality Drivetrains is essential to ensure durability and a perfect fit. Spicer ticks all of those boxes. We offer a wide selection of Spicer Drivetrains, specifically designed for the 1990 Chevrolet V3500. With over 3 Spicer brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $31.99, with an average price of just $39.99. Plus, with over 17 customer reviews and an average rating of 4.6 stars, you can trust that our Spicer Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from $48.99

(3)

Universal Joint

“Worked fine. Good service. They only pulled 1 part but the counter person went back retrieved what was necessary and completed the order quickly.”

from $31.99

(12)

Universal Joint, Greaseable 1310 Series OSR

“No problems with Installation and appears to be quality part! Great for my old School Street Car!”

from $38.99

(2)

Universal Joint

“I use this on a 4×4 off-road. It’s always a tough trade-off between the greaseable and non-greasable u-joints. The non-greaseable is stronger. The”

Popular Moog 1990 Chevrolet V3500 Drivetrains

Moog auto parts is one of the highest quality Drivetrain brands in the market. Any 1990 Chevrolet V3500 owner should feel confident when installing genuine Moog parts in their vehicle. To ensure the best fit and performance for your 1990 V3500, Advance Auto Parts carries a full inventory of 3 Moog Drivetrains. Plus you will be keeping your Chevrolet in peak condition while saving money because prices on these Moog Drivetrains range from $23.99 to $67.99, plus, with more than 31 customer reviews and an impressive 4.5 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from $29.99

(2)

Universal Joint Strap Kit

“Fit just like new. One difference I noticed was that the thread ran up the bolt farther but I doubt that will effect performance.”

from $67.99

(25)

Greaseable Premium Universal Joint

“I trust Moog I’m sure it will be on my truck for a while.”

from $23.99

(4)

Universal Joint U-Bolt Kit

“I used these to replace the factory originals that had over 80K miles on a 1964 Chevelle Malibu. I had a strange click in the differential area and s”

FAQs for 1990 Chevrolet V3500 Drivetrains

Which Drivetrains are best-sellers for 1990 Chevrolet V3500s?

Out of 198 Drivetrains that fit 1990 Chevrolet V3500s, the following parts are the top sellers:

Greaseable Premium Universal Joint (10086738) – $42.99
Greaseable Premium Universal Joint (10086900) – $35.99
Universal Joint (10265505) – $15.99

What’s the price range for 1990 Chevrolet V3500 Drivetrains?

Drivetrain prices for the 1990 Chevrolet V3500 start at $1.89 and go up to $1,008.00 for the most premium parts.

What’s the average price of a Drivetrain for a 1990 Chevrolet V3500?

The average price for Drivetrains for the 1990 Chevrolet V3500 is $143.59. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Chevrolet V3500 model years?

Yes, we currently carry Drivetrains for 1 model years of Chevrolet V3500s between 1989 and 1991. Drivetrains are bought most frequently for the following model years: 1991 and 1989.

What are the cheapest Drivetrains for my 1990 Chevrolet V3500?

The cheapest 1990 Chevrolet V3500 Drivetrains we carry in stock are:

Differential Ring Gear Bolt (10282457) – $1.89
Multi-Purpose Seal (3270890) – $3.99
Differential Crush Sleeve (10593146) – $3.99
Universal Joint (5270111) – $4.59
Universal Joint (5270049) – $5.39

What are the top-rated Drivetrains that fit the 1990 Chevrolet V3500?

Out of 4,518 reviews by customers, our 1990 Chevrolet V3500 Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 1990 Chevrolet V3500 and their top-rated products:

Universal Joints
- Universal Joint (10265508) – $15.99
- Greaseable Premium Universal Joint (10086919) – $67.99
- Universal Joint U-Bolt Kit (10086968) – $23.99
Spindles
- Universal Joint (10265508) – $15.99
- Greaseable Premium Universal Joint (10086919) – $67.99
- Universal Joint U-Bolt Kit (10086968) – $23.99

What types of Drivetrains do you sell for my 1990 Chevrolet V3500?

As of 3/1/26, these are some of the most in-demand types of Drivetrains for a 1990 Chevrolet V3500:

Can I get help with 1990 Chevrolet V3500 Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Chevrolet Drivetrains and more.

What is your return policy for Chevrolet V3500 Drivetrains?

Advance Auto Parts keeps returns simple. For new Chevrolet V3500 Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1990 Chevrolet V3500 Drivetrains

Dorman – Transfer Case Adapter O-Ring (Part No.926-831)

Yukon Gear – Differential (Part No.26042)

Powertrax – Lock Right Locker (Part No.1950-LR)

Motive Gear – Differential Carrier (Part No.6258336)

Schaeffler – Cup (Part No.M88010)

Dorman – U-Bolt Repair Kit (Part No.929-715)

National – Wheel Bearing (Part No.5707)

Schaeffler – Shaft Seal (Part No.SS3163)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.289)

National – Drive Shaft Center Support Bearing (Part No.HB-88107-A)

Yukon Gear – Full-Floating, Blank 35 Spline Diameter, Non-Drilled Axle Shaft For Dana 60 (Part No.21005)

Powertrax – Grip PRO Traction System (Part No.GT436035)

National – Multi-Purpose Seal (Part No.470682)

Yukon Gear – Differential (Part No.26039)

Felpro – Axle Housing Cover Gasket Irregular Shaped 10 Bolt Hole Gasket (Part No.RDS 6014)

Motive Gear – Transfer Case Bearing and Seal Kit (Part No.T1356R)

Dorman – Differential Cover (Part No.697-703)

Victor Reinz – Differential Cover Gasket (Part No.71-14868-00)

National – Shaft Repair Sleeve (Part No.99193)

National – Multi-Purpose Seal (Part No.710928)

Motive Gear – Differential Spool (Part No.FSD60-35L)

National – Bearing Race (Part No.HM903210)

Motive Gear – Differential Carrier Bearing Kit – Koyo (Part No.R10.5CK)

Pro-King – Differential Internal Nest Kit (Part No.744A717)

Motive Gear – Differential Carrier Shim Kit (Part No.1106)

Dorman – Differential Pinion Yoke Assembly (Part No.697-547)

MOOG Driveline Products – Universal Joint U-Bolt Kit (Part No.329-10)

Motive Gear – Differential Pinion Nut (Part No.15994582)

Valvoline – MaxLife Multi-Vehicle Automatic Transmission Fluid, 1 Gallon (Part No.773775)

Valvoline – High Performance Transmission & Differential Gear Oil: Conventional 80W-90, 1 Quart (Part No.VV831)

National – Bearing Race (Part No.382A)

Felpro – Axle Housing Cover Gasket Irregular Shaped 10 Bolt Hole Gasket (Part No.RDS 6014)

National – Shaft Repair Sleeve (Part No.99193)

Felpro – Axle Housing Cover Gasket: Irregular Shaped 14 Bolt Hole Gasket (Part No.RDS 55063)

Dorman – Differential Cover (Part No.697-703)

Felpro – Axle Housing Cover Gasket Irregular Shaped 10 Bolt Hole Gasket (Part No.RDS 6095-1)

Yukon Gear – 3 Qt – 80W90 Conventional Gear Oil With Posi Additive (Part No.15003)

Yukon Gear – 3 Qt – Penzoil 80W90 Conventional Gear Oil (Part No.15002)

Dorman – Help – Pinion Crush Sleeves (Part No.81057)

National – Multi-Purpose Seal (Part No.9316)

Motive Gear – Drive Shaft Pinion Yoke (Part No.MG1310-6010)

National – Tapered Roller Bearing Cone (Part No.HM803146)

National – Bearing Race (Part No.HM88510)

Yukon Gear – Redline Synthetic "Shock Proof" Oil With Positraction Additive – 4 Quarts (Part No.15005)

National – Bearing Race (Part No.HM803110)

Motive Gear – Differential Pinion Seal (Part No.9316)

Motive Gear – Differential Pinion Shim Kit (Part No.1118)

National – Tapered Roller Bearing Cone (Part No.HM903249)

Yukon Gear – Redline Synthetic "Shock Proof" Oil – 3 Quarts (Part No.15000)

National – Tapered Roller Bearing Cone (Part No.469)

National – Bearing Race (Part No.HM903210)

National – Bearing Race (Part No.HM807010)

Warn – Hubs – 4WD (Part No.11690)

Carquest Premium – 4WD Actuator (Part No.FWC1088)

Pro-King – Differential Shift Actuator (Part No.742D421A)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.374)

Spicer – Universal Joint, Greaseable 1310 Series OSR (Part No.5-153X)

MOOG Driveline Products – Universal Joint Strap Kit (Part No.492-10)

MOOG Driveline Products – Universal Joint U-Bolt Kit (Part No.329-10)

MOOG Driveline Products – Double Cardan CV Ball Seat Repair Kit (Part No.606)

Driveworks – Universal Joint (Part No.DW-331BL)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.534G)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.369)

Driveworks – Universal Joint (Part No.DW-534G)

MOOG Driveline Products – Universal Joint Strap Kit (Part No.530-10)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.234)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.269)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.280)

Driveworks – Universal Joint (Part No.DW-374)

Spicer – Universal Joint (Part No.5-795X)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.232)

Driveworks – Universal Joint (Part No.DW-369)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.235)

Driveworks – Universal Joint (Part No.DW-331)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.231)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.331)

Spicer – Universal Joint, Greaseable S44/3R Series (Part No.5-3147X)

Driveworks – Universal Joint (Part No.DW-235)

Dorman – Help – U-Joint Repair Assortment 2 Pc (Part No.81020)