from

$288.99

Set-up carrier bearing kti (2 bearings, no races) for Dana 70 HD and Dana 80. 469. No return.

Product Features:

Set up bearing kit
Fits Dana Spicer 80
Easily slips on and off carrier journals to allow for easier carrier shim adjustment

from

$211.99

Product Features:

GM10.5″ 14 BOLT OPEN EMPTY CASE 4:10 & DWN

from

$12.99

10.5″ GM 14 bolt truck crush sleeve, 1989 & newer. Approx 0.920″ long.

Product Features:

Crush sleeve for 1989 and up GM 10.5″ 14 bolt truck
0.920″ tall

from

$5.99

DiffrlPinSupportBolt

from

$436.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 1998 and up GM 10.5″ 14 bolt truck
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$8.99

14T pinion gear Thrust washer.

Product Features:

Pinion gear thrust washer
Fits GM 10.5″ 14 bolt truck

from

$198.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket. All products are designed to meet or exceed OE quality, form, fit and funtion.

Product Features:

High strength steel
Dual heat treating process

from

$15.99

O-ring for left hand carrier bearing adjuster for 9.25″ GM IFS.

Product Features:

Axle o-ring
Fits Chrysler 9.25″ IFS

from

$323.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$188.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M802011 race
All steel construction

from

$249.99

Product Features:

Spider gear kit
Fit Dana Spicer 70 and 80 open differential with 35 spline axles
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$181.99

Dana 60 & Dana 70 Power Lok clutch set (steel & fiber).

Product Features:

Clutch kit
Fit Dana Spicer 60, 70, 70U and 70HD Powr Lok positraction

from

$12.99

GM 9.5″ ring gear bolt. 12mm x 1.5.

Product Features:

Ring gear bolt for GM 9.2″
12mm x 1.5

from

$939.99

Differential

from

$1168.99

Differential

from

$7.99

Product Features:

Oil baffle
Fits Dana Spicer 70 and 70HD

from

$99.99

Standard Open cross pin shaft for four pinion design for GM 14T.

Product Features:

Cross pin shaft
Fits GM 10.5″ 14 bolt truck

from

$287.99

Yukon mini spool for GM 10.5″ 14 bolt truck.

Product Features:

Fits 10.5″ GM 14 bolt truck
Provides 100% traction to both wheels at all times
Installs into standard open carrier case

from

$7.99

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
0.225″ diameter
1.870″ long

from

$288.99

Product Features:

Nodular iron for added strength
Thick design
Durable powder coat finish
Magnetic drain plug
Made in USA
High strength stainless steel fasteners

from

$13.99

Product Features:

Carrier shim kit for Dana Spicer 60, 70, 70HD, 70U and 80

from

$9.99

Product Features:

Preload spacer
Fits Dana Spicer 70

from

$39.99

Replacement pinion seal for Dana 44HD, Dana 60 & Dana 70 .Yukon Mighty seal.

Product Features:

Pinion seal
Pinion seal
Fits Dana Spicer 44HD, 60, 70, 70U and 70HD

from

$117.99

Product Features:

PINION YOKE
CAST:1310
U-BOLT STYLE

from

$487.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

Product Features:

Powertrax® proves that you don’t have to choose between the superior traction of a locking differential and smooth handling and drivability of an open differential. Powertrax Lock-Right Lockers, No-Slip Traction Systems and GRIP limited slip differentials and lockers give you the best of both worlds!
The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.
Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.
Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.
Powertrax® = Extreme Traction Systems!

from

$567.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

Fits Dana Spicer 70
10.50″ ring gear diameter
29 spline pinion
12 ring gear bolts
4.56 ratio

from

$77.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$446.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits Dana Spicer 80 with 4.125″ O.D. pinion bearing
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, oil baffles and slingers, thread locker, marking compound with brush and silicone.