1989 Chevrolet Caprice Drivetrains
More 1989 Chevrolet Caprice Drivetrains Categories
If you’re looking for an original Drivetrains replacement for a 1989 Chevrolet Caprice, you can search through our selection below. You’ll also find aftermarket and OEM Drivetrains to meet your needs.
Essential 1989 Chevrolet Caprice Drivetrains
ARP Auto Racing – For Use With General Motors, 0.800" Head L, 3/8" – 24 Thread Size, Chrome Moly (Part No.230-3001)
from
$40.49
The tremendous shock loads generated at launch by most any drag racing vehicle equipped with todays sticky tire compounds or the acceleration and deceleration of oval track cars put considerable strain on the ring gear. For this reason, the fastener experts at ARP have developed the Pro Series ring gear bolts. They are forged from premium grade 8740 chrome moly steel and are heat treated to a nominal rating of 200,000 PSI tensile strength. Specially hardened, precision ground washers are included where required. Available to fit most any ring gear setup ranging from popular 9 Inch Ford GM 10 and 12 bolt rear ends to the beefy strange differentials found in top fuel and funny car applications.
Product Features:
See More
Product Features:
- Forged From Premium Grade 8740 Chrome Moly Steel
- Heat Treated
- Nominally Rated At 200,000 Psi Tensile Strength
- Specially Hardened, Precision Ground Washers
- 3/8″-24 RH Thread Size
- 0.8″ Underhead Length
- 200,000 PSI
USA Standard Gear – Master Overhaul Kit for the GM 8.5 Differential with HD Posi or Locker (Part No.37057)
from
$208.99
USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.
Product Features:
See More
Product Features:
- Fits GM 8.5″ rear with aftermarket positraction
- Uses Koyo bearings and races
- Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.
Yukon Gear – Positraction Pinion Gear Thrust Washer With Step-Lip Inside For GM 12P And 12T – Fits New Eatons (Part No.33382)
from
$14.99
Positraction pinion gear thrust washer with step-lip inside for GM 12P and 12T. fits new Eatons.
Product Features:
See More
Product Features:
- Pinion gear thust washer for GM 12 bolt passenger car and truck
- Fits positraction designs only
- Has inside lip
Yukon Gear – Super Carrier Shim Kit For Ford 7.5", GM 7.5", 8.2" & 8.5" (Part No.55001)
from
$59.99
Product Features:
See More
- Super carrier shim kit for Ford 7.5″, GM 7.5″, 7.625″, 7.6″ IFS, 7.6″ IRS, 7.75″, 8.2″, 8.2″ Buick, Oldsmobile and Pontiac and GM 8.5″ front and rear
- Interlocking design makes installation much easier
Yukon Gear – Yoke For GM 8.2" With A 1310 U/Joint Size – This Yoke Uses U-Bolts (Part No.41094)
from
$219.99
Yukon yoke for GM 8.2″ with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits GM 8.2″
- 25 spline
- 1310 u-joint size
- 3.219″ snap ring span
- 1.062″ cap diameter
- Outside snap ring design
- U-bolt style
Dorman – Spindle Nut (Part No.K1002831647DOR)
from
$5.57
Spindle Nut
SKF – Pinion Seal (Part No.J7010211355SKF)
from
$16.53
Pinion Seal
Dorman – Spindle Washer – I.D. 3/4 In. O.D. 1-21/32 In. Thickness 3/32 In. (sold by each) (Part No.618-005)
from
$3.49
This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Felpro – Differential Cover Gasket (Part No.RDS 30031)
from
$8.79
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Driveworks – Tapered Roller Bearing (Part No.S-A-9)
Yukon Gear – Standard Open Spider Gear Kit For GM 12 Bolt Car And Truck With 30 Spline Axles (Part No.16043)
from
$207.99
Yukon standard open spider gear kit for GM 12P and 12T with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Spider gear kit
- Fits GM 12 bolt passenger car and truck open differential with 30 spline axles
- Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
Driveworks – Tapered Roller Bearing (Part No.S-LM-603012)
Pro-King – Differential Internal Nest Kit (Part No.742G717A)
from
$179.99
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.
Product Features:
See More
Product Features:
- All products are designed to meet or exceed OE quality, form, fit and funtion.
Motive Gear – Differential Gear Install Kit (Part No.GM8.2IK)
Yukon Gear – Pinion Nut Washer (Part No.33167)
from
$14.99
Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.5″, 8.6″ & 9.5″.
Product Features:
See More
Product Features:
- Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.625″, 7.6″ IFS, 8.5″, 8.6″ and 9.5″.
Motive Gear – Differential Mini Spool (Part No.MS10-28)
Yukon Gear – Replacement Bare Case For GM 8.5" & 8.6" Dura Grip (Part No.20107)
from
$386.99
Replacement bare case for GM 8.5″ & 8.6″ Yukon Dura Grip. Fits both 28 & 30 spline applications. This carrier case is for a Yukon Dura Grip ONLY. It is NOT a replacement carrier for a stock positraction.
Product Features:
See More
Product Features:
- Dura Grip positraction carrier case
- Does not include spider gears
- Fits GM 8.5″ and 8.6″
- Fits 2.76 and up ratios only
Motive Gear – Differential Mini Spool (Part No.MS7.5-28)
Yukon Gear – Positraction Internals For 7.5" And 7.625" GM With 28 Spline Axles (Part No.16117)
from
$279.99
Yukon positraction internals for 7.5″ and 7.625″ GM with 28 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects. This kit fits Yukon Dura Grip & Eaton positraction cases. It is not compatible with any other positractions.
Product Features:
See More
Product Features:
- Spider gear kit
- Fits GM gm 7.5″ and 7.625″ with 28 spline Dura Grip positraction
- Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.
Yukon Gear – Billet Yoke For GM 12P And 12T With A 1350 U/Joint Size (Part No.41154)
from
$359.99
Yukon billet yoke for GM 12P and 12T with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits GM 12 bolt passenger car and truck
- 30 spline
- 1350 u-joint size
- Outside snap ring design
- 3.625″ snap ring span
- 1.188″ cap diameter
- U-bolt style
Yukon Gear – 8.6" GM 12P 12T & F8.8 Carrier Installation Kit (Part No.57010)
from
$121.99
Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.6″, 12 bolt car and 12 bolt truck differential. This kit contains carrier bearings, races and shims.
Product Features:
See More
Product Features:
- Fits GM 12 bolt passenger car and truck and 8.6″
- Includes carrier bearings and races and “super” carrier shim kit
National – Bearings (Part No.M88010)
from
$10.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – R1563Tav Rear Axle Bearing And Seal Kit (Part No.10004)
from
$42.99
Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1563TAV axle bearing and seal kit, TorringtonBrand, 2.250″ OD, 1.400″ ID. This axle bearing & seal kit services one side only.
Product Features:
See More
Product Features:
- Includes axle bearing and seal
- Services one side
- Torrington Brand
- 2.250″ O.D.
- 1.400″ I.D.
Dorman – Spindle Washer – I.D. 3/4 In. O.D. 1-21/32 In. Thickness 3/32 In. (Part No.618-005.1)
from
$3.79
This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
National – Multi Purpose Seal (Part No.8660S)
from
$8.99
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Low swell in hydrocarbon fluids
- Design type: spring loaded; multi-lip
- Provides good low temperature capability
- Temperature range: -40°F to 225°F; -40°C to 107°C
- Delivers quality and reliable performance for every type of repair
Yukon Gear – Posi Shim Kit For GM 7.5" & 7.625" Eaton Positraction (Part No.16047)
NTN – Axle Shaft Bearing (Part No.K4010212752NTN)
from
$42.90
Axle Shaft Bearing
Driveworks – Axle Repair Bearing (Part No.S-RP-6408)
from
$24.29
Value-priced bearing meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
Popular 1989 Chevrolet Caprice Drivetrains Categories
1989 Chevrolet Caprice Drivetrains
You count on your 1989 Chevrolet Caprice to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 357 Drivetrains ranging in price from $1.99 to $1,153.99, you’re sure to find everything you need for your 1989 Chevrolet Caprice.
Brands matter. If you want to shop a specific Drivetrains brand, we stock 19 different brands like Valvoline, Moog, and Driveworks. 1989 Chevrolet Caprice Drivetrains start as low as $1.99!
One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 8,911 extensive product reviews on 1989 Chevrolet Caprice Drivetrains. Some of the top-rated Drivetrains products we carry are Universal Joint with 4.6 stars and Greaseable Super Strength Universal Joint with 4.2 stars.
Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 1989 Chevrolet Caprice below to get started!
Top-Rated Drivetrains Brands For Your 1989 Chevrolet Caprice
Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1989 Chevrolet Caprice running right for years to come. In our inventory you’ll find brands like Valvoline, Moog, Driveworks, and even more.
Popular Powertrax Drivetrains
You’ll find popular Powertrax brand products across Differentials. All are waiting to get your 1989 Chevrolet Caprice back on the road. Some of the top-rated Powertrax products in these categories are:
Top-Rated Drivetrains
If are what you’re looking for, our inventory holds plenty. We stock brand Drivetrains for your 1989 Chevrolet Caprice, and some of our most reviewed parts include:
from
$12.79
(446)
MaxLife Multi-Vehicle (ATF) Full Synthetic Automatic Transmission Fluid, 1 Quart
Differential Oil
FAQs for 1989 Chevrolet Caprice Drivetrains
What are the most purchased Drivetrains for the 1989 Chevrolet Caprice?
Out of 357 Drivetrains for the 1989 Chevrolet Caprice, the most popular in our inventory are:
What are the top-rated 1989 Chevrolet Caprice Drivetrains?
Top-rated Drivetrains for your 1989 Chevrolet Caprice based on customer reviews/ratings are:
from
$34.99
(48)
Greaseable Super Strength Universal Joint
“Moog and advanced auto got me out of a bad situation with an amazing part ( u”
from
$7.99
(45)
DIFFERENTIAL GASKET
“Some say no need for a gasket and to use gasket sealer only its just as good. I like to make sure that the cover is installed properly to avoid any l”
