from

$4.79

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$12.99

Product Features:

Cross pin shaft for Dana Spicer 30
Fits standard open differentials only

from

$26.99

Product Features:

Carrier shim kit for Dana Spicer 30 and Dana Spicer 44 with 19 spline axles

from

$13.99

Product Features:

O-ring for seal housing
Fits Dana Spicer 30 and AMC Model 35

from

$3.99

Replacement pinion nut washer for Dana 25, 27, 30, 36, 44 & 53.

Product Features:

Pinion nut washer for Dana Spicer 25, 27, 30, 44 and 50

from

$155.99

Yukon replacement standard open spider gear kit for Dana 30 with 27 spline axles and with or without quick disconnect. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fit Dana Spicer 30 open differential with 27 spline axles
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$312.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits Ford 7.5″
7.50″ ring gear diameter
28 spline pinion
10 ring gear bolts
4.56 ratio

from

$42.99

Chrome cover for 7.5″ Ford.

Product Features:

Fits Ford 7.5″
Chrome

from

$444.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$6.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$123.99

Product Features:

CLUTCH PACK KIT 8.8″ FORD 1 KIT PER UNIT

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$307.99

Yukon replacement yoke for Dana 30, 44, and 50 with 26 spline and a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 30 and 44
26 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
Strap style

from

$1.99

Product Features:

Ford 7.5″, 8.8″ Ring Gear Bolt

from

$383.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits AMC Model 35 IFS
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, axle seals, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

from

$13.79

Formulated to meet the specific requirements of Subaru vehicles equipped with conventional (non-CVT) transmissions up to model year 2005. Recommended for service-fill in all Subaru automatic transmissions where SUBARU ATF HP is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. IDEMITSU is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. IDEMITSU application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.

Product Features:

Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
Provides superior cleanliness, maintaining the transmission free of sludge and varnish deposits
Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
Advanced anti-wear technology provides maximum protection to gears and bearings

from

$10.99

Replacement pinion nut for Model 20 & 35, Dana 30 JK, 44 JK front, Ford 10.25″, 10.5″ & some 9.75″. 7/8-20 thread, 1 1/8 socket.

Product Features:

Pinion nut for Jeep JK front, Jeep Liberty front, Ford 9.75″, 10.25″, 10.5″ and AMC Model 20 and Model 35
7/8″ x 20 thread
1 1/8″ socket

from

$37.99

7.5″, 8″, 8.8″, 9″, 10.25″ Ford REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Ford 7.5″, 8.8″, 9″ and 10.25″

from

$7.99

Dana 28 & Dana 30 pinion gear Thrust washer. Also fits AMC Model 35 with 1.560″ side gear bore only.

Product Features:

Pinion gear thrust washer for Dana Spicer 25, 27 and 30

from

$10.99

Dana 25, Dana 27, & Dana 30 side gear Thrust washer.

Product Features:

Side gear thrust washer for Dana Spicer 25, 27, 30 and AMC Model 35
1.560″ I.D.
Fits standard open differentials only

from

$356.99

Yukon 1541H alloy 5 lug right hand rear axle for 7.5″ and 8.8″ 2WD van (left hand for Aerostar) with a length of 32-1/4″ inches and 28 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a C-clip axle.

Product Features:

28 spline
5 lug
32.25″ long
Fits Ford 7.5″ and 8.8″ in 1986-1997 Aerostar
Left hand side

from

$109.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.2″ & 8.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits GM 7.5″, 7.625″ 8.2″ and 8.5″
Includes carrier bearings and races and “super” carrier shim kit

from

$259.99

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

Fits AMC Model 35 IFS
Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, marking compound and brush.

from

$17.99

Precision cut and high quality materials. Reusable.

Product Features:

Precision cut
High-quality materials
Reusable

from

$17.99

Yukon 1541H alloy right hand rear axle for Model 35 (drum brakes) with a 54 tooth, 2.7″ ABS ring. axle has a length of 29-1/4″ inches and 27 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H allo

Product Features: