Name: Intake Manifold Bolts
Brand: Mr. Gasket
SKU: 6091
Price: 32.09 USD
Rating: 4.5 (5 reviews)

from

$32.09

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

Features 12-point Smaller-than-standard Bolt Head
Thick Flat Washers Distribute Optimum Clamp Load
Ideal Use Where Space Is Minimal On Race Manifolds
Bolts And Washers Zinc Plated For Protection
Zinc Plated For Protection

from

$43.99

Fits Chevy small block 265-400 CID, Chevy big block 396-454 CID, & 90 degree Chevy V6. The Starter Motor Heat Shield is built with heat-resistant material sandwiched between two aluminum plates. The shield protects the starter from heat buildup from the exhaust system, especially important when using headers.

Product Features:

Designed to prevent starter overheat due to extreme exhaust temperature
Heat resistant material sandwiched between 2 aluminum plates
Protects Starter From High Temperatures
Made Of 2 Sheets Of Aluminum Heat Resistant Center
Natural Finish

from

$214.49

Hypertech ThermoMaster Power Chips are engineered for stock 1995-1981 GM vehicles (premium octane fuel required). The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. ThermoMaster Power Chips are designed for daily street driving or competition in unmodified vehicles using a 160 Deg. or 180 Deg. thermostat. Hypertech Power Chips(TM) are emissions certified 50-state legal (application specific).

Product Features:

Use w/Low-Temp 160-180 Deg. PowerStat Thermostat
Controls Engines Air/Fuel Ratio
Controls Spark Advance For Max Power
Potential Gas Mileage Improvements
No Wiring Or Soldering Required
Installs In Less Than 30 Minutes
Product might not be available in all states due to local laws.

from

$850.99

Holley designed these throttle bodies with all relevant emission provisions and hook-ups for a true 50 state legal installation. They are engineered for a bolt-on installation on stock factory Manifolds for the applications cataloged. The one barrel throttle bodies have been assigned California Air Resources Board (C.A.R.B.) Executive Order (E.O.) number D-115-4. The two barrel throttle replacement bodies are considered to be the functional equivalent of the original equipment throttle body and, as such, are considered to be 50-State legal.

Product Features:

Direct Replacement For OE Units
2 in. Throttle Bore
42 percent Area Increase Over Stock TBI
Including Air Distribution Ring
Increased Torque and Horsepower
50 State Legal

from

$576.99

Product Features:

6500-10000 RPM Range
Dual Plane Quad Type – 4150 Style Flange
7.13 in. Front Height, 7.13 in. Center Height, 7.13 in. Rear Height
Satin Finish
Base Only

from

$339.99

Torque Converter – Tork Master 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best value priced street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New alloy steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required. Due to torque converter core availability, the actual converter size may vary but performance functionality will be as advertised.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$83.99

The Edelbrock #4680 Signature Series Valve Covers are designed for Chevrolet 396-502 V8 ’65 & later applications. Engineered for function and styled for great looks, Signature Series valve covers have stock-style breather baffles that prevent oil passage to the PCV valve. These quality valve covers accept all emissions equipment, including PCV valve holes. Rubber grommets for the breather and PCV valve holes are included. Matching breathers sold separately.

Product Features:

Big Block Chevy 396-502 1965 & Up
Tall
Chrome Steel
Set Of Two
Rubber Grommets For Breather

from

$111.99

Will replace distorted and worn-out original rubber mounts to maintain car body and truck cab to bed alignment. Original rubber mounts are so soft they often crack, distort, and crush so badly they often fall off and aluminum body mounts are too harsh for street use that they tend to break and cause other components to break. Energy’s specially formulated Hyper-Flex polyurethane cab and body mounts combine the best qualities of both: they’re soft enough for a smooth ride, yet rugged enough for the most demanding road or track. Most sets have a strong zinc plated steel ring molded into them – for added durability and when the application requires it.

Product Features:

Assures Longer Lasting Cab to Bed Alignment
Replace to Restore Ride Height
Gain Durability
Stronger Than Original Rubber Mounts

from

$284.99

HYDRAULIC – High Energy: Vans, pickups, 4WD and towing, in 350c.i., good idle, strong mid-range torque. OR High Energy Marine: Single or dual engine with inboard/outboard drive for ski and economy.

Product Features:

HYDRAULIC – High Energy: Vans, pickups, 4WD and towing, in 350c.i., good idle, strong mid-range torque. OR High Energy Marine: Single or dual engine with inboard/outboard drive for ski and economy.
260/260 Advertised Duration, 212/212 Duration @ .050″, .440″/.440″ Lift, 110 Lobe Separation
Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

from

$499.99

Power Train

from

$129.99

Designed to reduce wheel shimmy and end vibration caused by larger tires, the Rancho® steering stabilizer kit cuts down on steering arm fatigue to improve handling. The kit includes one Rancho RS5000® steering stabilizer and installation brackets.

Product Features:

COMPATIBILITY — Designed for a variety of Chevrolet® and GMC® trucks and SUVs
IMPROVED HANDLING AND PERFORMANCE — Reduces wheel shimmy, bump steer and vibration which helps minimize on- or off-road driver fatigue
ACCOMMODATES LARGER TIRES — Engineered for vehicles with oversized wheels and tires.
ENGINEERED TO LAST — Features protective boot to shield shock rod and oil seal and 0.25-in. high-strength, low-alloy steel bracket construction for long life
EASY TO INSTALL — Includes one Rancho RS5000® steering stabilizer and brackets that bolt directly to factory steering linkage with included mounting hardware, no modifications needed
RESISTS CORROSION — Durable black powder-coated and/or zinc-plated brackets resist rust and corrosion
PRECISION DESIGN — Brackets are CNC cut and bent to exact specifications for a perfect fit

from

$203.99

Edelbrock part #9646 Pushrods are designed for small-block Chevy V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise forme

Product Features:

7.25 in. Length
0.312 in. Diameter
4130 Chromoly Steel Material
Black Oxide Finish
Made In The USA

from

$20.29

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Steel core gasket construction
Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
Not intended for use in emission controlled vehicles.

from

$368.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$109.99

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

Less than 50 ohms per foot for superior spark
Ferro-magnetic impregnated core creates an effective EMI choke
40 ft. Of Conductor Wound Into A Single Foot Of Wire
For high EMI suppression
Conductor core features Dupont Kevlar material
Proprietary compound sleeves for resistance to high heat/abrasion

from

$79.99

Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Compatible with late model GM computer controlled remote mount HEI systems. Direct bolt-in, plug-in replacement. Brass coil wire contact increases energy transfer and resists corrosion better than aluminum. Complete with new mounting hardware.

Product Features:

10-15% More Energy
Direct Plug In Replacement Direct OE Fit
Advanced Bobbin Technology
Highly Specialized Silicone Magnetic Steel Cores
Standard Motor Products SMP DR-37
MSD 8226
Resist Corrosion
W/New Mounting Hardware

from

$99.99

Product Features:

Use W/ Valve Springs Part #5703, 5794
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$39.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$349.99

K&N air intake systems are engineered for increased performance, outstanding durability, and sleek aesthetics – and are available in an assortment of finishes and powder coatings. K&N’s state-of-the-art High-Flow Air Filter helps to shield your engine from contaminants, while a meticulously engineered aerodynamic tube design contributes to a guaranteed increase in horsepower and torque. K&N air intake systems are designed to improve acceleration, towing, and throttle response while providing world class protection for your engine. Our intakes are dyno-tested and provide up to 50% more airflow compared to OEM intake systems. K&N intakes are easy to install and maintain with air filter cleaning required only every 100,000 miles.

Product Features:

GUARANTEED INCREASE IN HORSEPOWER: Dyno-tested with up to 50% more airflow than restrictive factory box air filter and intake tube
BETTER TOWING: Improves acceleration and uphill performance when towing by improving throttle response.
IMPROVED ENGINE SOUND: Hear the power under the hood.
WORLD CLASS PROTECTION: Pushing the limits of engine protection by protecting your engine from harmful contaminants
EASY MAINTENANCE: No filter cleaning required for up to 100,000 miles
EASY TO INSTALL: Bolt-on power in less than an hour with basic hand tools. K&N air intake systems are one of the easiest ways to guarantee an increase in horsepower.
DYNO TESTED: Dyno-tested for a guaranteed increase in horsepower and acceleration with no ECU tune required
HIGH QUALITY: Made in America.

from

$439.99

The B&M Quicksilver features a ratcheting action for positive shifts, Chrome Knob, neutral safety switch, NHRA/IHRA approved Reverse Lockout. Fits Most 3 and 4 speeds.

Product Features:

Universal Floor Mount Application
Base Trimmed For Custom Fit
Cable Operated
Quick Installation
Accurate Shifting

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$184.99

Product Features:

Remote Thermostat Housing

from

$16.99

FRAM Racing® filters are designed with a heavy-gauge tapping plate and an extra-thick* steel can that is able to withstand the high pressure flexing caused by demanding driving conditions. A spiral-shaped center tube provides protection against collapse, and tough steel end caps add even more durability. A screen-over 22psi filter bypass valve provides additional protection against larger contaminants.**

Product Features:

Proven protection for up to 10,000 miles
Engineered for use with synthetic or conventional motor oils
Filter media is a blend of fiber and resin that captures 95% of the dirt particles
The perfect balance of dirt-trapping efficiency and dirt-holding capacity

from

$158.89

Hypertech Power Chips are engineered for stock 1981-1995 GM vehicles. The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. Street Runner Power Chips are designed for daily street driving or competition in unmodified vehicles using a stock thermostat.

Product Features:

Designed For Daily Street Driving
For Unmodified Vehicles w/Stock Thermostat
Controls Engines Air/Fuel Ratio
Controls Spark Advance For Max Power
Potential Gas Mileage Improvements
No Wiring Or Soldering Required
Installs In Less Than 30 Minutes
Product might not be available in all states due to local laws.

from

$126.99

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

Product Features:

Seat pressure: 105 lbs. @ 1.700″, Open Pressure: 273 lbs. @ 1.250″
O.D.: 1.254″, I.D.: .880″
Single valve springs with damper
Approximately .490″ max lift at recommended installed height

from

$78.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$31.99

ACCEL high performance standard size caps offer superior protection from arc-thru and crossfire. Features hi-performance. 60kV- rated alkyd compound, stress-relieved at molding to ensure stability. Brass inserts provide for high spark energy flow.

Product Features:

Brass Inserts Provide For High Spark Energy Flow

from

$443.99

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features: