1988 Chevrolet C1500 Differentials

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

• Direct replacement – this differential end yoke matches the fit and construction of the original yoke
• Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
• Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
• Validated fit – this differential end yoke has been tested to confirm accurate fit

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

• Fits GM 18.5″ with 28 spline axles
• Made from 9310 steel for added strength
• Replaces the spiders in a standard carrier case

Pro-King is the leading supplier of transmission and driveline products in the aftermarket. All products are designed to meet or exceed OE quality, form, fit and funtion.

Product Features:

• High strength steel
• Dual heat treating process

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits HM88610 race
• All steel construction

Product Features:

• Cross pin bolt
• Fits GM 9.5″ and 9.25″ IFS

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits 1998 and up GM 9.5″
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

• Premium bearing design matches OEM specifications
• Precision manufactured using premium-grade steel for outstanding durability and performance
• Crowned raceways and rollers to ensure even load distribution for maximum life
• Industry leading coverage
• Professional technicians know they can depend on National

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Unsurpassed quality you can trust
• Validated for fit, form and function
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

Pinion nut for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.0″, 8.25″, 8.5″, 8.6″, 9.25″ IFS, 9.5″ & Oldsmobile Dropouts. 1 1/4″ socket, 7/8″ x 14 thread.

Product Features:

• Pinion nut for GM 7.2″, 7.5″, 7.625″, 8.0″, 8.25″ IFS, 8.5″, 8.6″, 9.25″ IFS and 9.5″
• 7/8″ x 14 thread
• 1 1/4″ socket

Pennzoil? Synchromesh Fluid is designed to offer optimal protection for moderately loaded gears in manual transmissions. Containing a high detergent additive system, it helps cope with water, dust, dirt, and any other small deposits you might encounter on or off-road(1). Pennzoil? Synchromesh Fluid also offers synchronizer compatibility for performance in manual transmissions, specifically to fulfill the needs of Chrysler, GM, Honda and other transmission requirements. Pennzoil? Synchromesh Fluid meets General Motors specification 9985648 for use where GM part numbers 12345349 or 12345577 are called out for use. Chrysler manual transmission fluid specification MS-9224 is also met. This high quality manual transmission fluid is formulated for good low temperature flow to maintain shift characteristics even after a cold night(2). Corrosion protection is added to help protect your transmission. Pennzoil? Synchromesh fluid is a manual transmission fluid designed for certain manual trans axles and manual transmissions used by general motors or Chrysler. (1)The Anglamol 6091 additive system contains approximately twice the sulfonate detergent levels as current generation PCMO, 4500 ppm as magnesium of magnesium sulfonate. This engine oil type additive will emulsify water and polar contamination sufficiently to handle contamination levels above 0.5% water. Anglamol 6091 – Detergent, friction modifier, extreme pressure agent, seal swell, anti-wear, anti-oxidant. Chemical Composition – Magnesium sulphonate, alkenyl amide, alkenyl ester sulphide, alkenyl phosphite, alkylbenzene, hecterocyclic ether, zinc dithiophosphate. (2)Pour point is less than -39 Deg. C. Low temperature viscosity in a -40 Deg. C Brookfield test of 50,000 cPs maximum, less than a 75W gear oil and the cold cranking viscosity less than a typical conventional SAE 5W engine oil.

Product Features:

• Excellent yellow metal compatibility
• Meets GM specification 9985648 and Chrysler specification MS-9224
• Excellent synchronizer performance
• Exhibits excellent low-temperature performance

Pinion seal for GM 8.5″, 8.2″, Buick, Oldsmobile, and Pontiac.Yukon Mighty seal.

Product Features:

• Pinion seal
• Fits GM 8.5″ rear, 8.2″ and 8.2″ in Buick, Oldsmobile and Pontiac

8.25″ IFS, 8.5″, 12P, 7.5″ F, 8.8″ F, 8.25″ Chrysler pinion shim kit.

Product Features:

• Pinion depth shims for GM 8.25″ IFS, 8.5″, 8.6″, 12 bolt passenger car, Ford 7.5″ and 8.8″, Chrysler 8.25″

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

• Fits 1998 and up GM 9.5″
• Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

Yukon standard open spider gear kit for 8.5″ GM with 28 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fits GM 8.5″ open differential with 28 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects. This unit has larger bearing journals for added strength & uses heavy-duty carrier bearings & races.

Product Features:

• Fits GM 8.5″ with 28 spline axles
• 2.73 ratio and up only
• 4-spring, clutch style positraction
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

• Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
• 1/2″ head

Chrome Moly cross pin shaft for Mini-Spool for 8.5″ GM HD.

Product Features:

• Cross pin shaft
• Fits GM 8.5″
• Chromoly steel for added strength

Product Features:

• Shim kit
• Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction

Ring gear bolt for GM 7.5″, 7.6″, 7.6″ IRS, 8.0″, 8.25″ IFS, 8.5″, 8.6″ & 8.6″ IRS. 7/16″ x 20.

Product Features:

• Ring gear bolt for GM 7.5″, 7.625″, 7.6″ IRS, 8.0″, 8.25″ IFS, 8.5″, 8.6″ and 8.6″ IRS
• 7/16″ x 20

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Product Features:

• KIT SHIM SIDE 9.5″ GM

This kit uses Koyo bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. USA Standard Gear does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

• Fits GM 8.5″ rear
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, pinion nut, crush sleeve, marking compound and brush.

Product Features:

• Clutch kit
• Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
• 14 piece kit
• Carbon fiber clutches

Positraction clutch guide.

Product Features:

• Clutch guide for Chrysler 9.25″, Dana Spicer 44, Dana Spicer 50, Ford 8.8″, GM 12 bolt passenger car, GM 8.2″, 8.5″ and 8.6″, 1963-1979 Corvette and Nissan Titan
• Compatible with Dura Grip positractions only